132kv MOCB acceptable value of somthing 150 micro ohms.
220v, 415v, 6.6 kv, 11kv,33kv,132kv,400kv
it depends on the specification,,,,,,in saudi arabia as per sec standards 152kv voltage should be applied for a period of one hour.
Its just a matter of standard. In my area, for instance, we use 13.2 KV for distribution lines, and 69 KV / 138 KV for transmission lines.
These are the nominal voltages used by the UK's distribution system, although (to comply with European Harmonisation requirements, 415 V has now been 'replaced' with 400 V. Incidentally, the symbol for the volt is a capital 'V', not a lower-case 'v'.
132kV substation is part of transmission and distribution of power in which the transmission voltage is 132kV. The substation is for stepping down or stepping up of the voltages to the required voltage. the substation also serves as a place where the transmission lines can be isolated, controlled and monitored. The substation consists of different equipment that is used to regulate, monitor and distribute the required power.Another AnswerIn the UK, 132 kV voltages are considered to be the lowest transmission voltages. Other transmission voltages are 275 kV and 400 kV. A '132-kV substation' is normally one in which this voltage is stepped down to a primary distribution voltage, usually 33 kV but, sometimes, 66 kV. As the previous answer points out, substations contain transformers, switchgear, busbars, and protection equipment.
9 insulators
it means..it is stepping up the power of 132KV to 380KV on the transmission lines.
The safety distance from a 132 kv powerline is 1.4 metres
220v, 415v, 6.6 kv, 11kv,33kv,132kv,400kv
Refer IEEE 80- 2003 For Design of grounding of 132kV substation.
Usually HV is 33KV and 66KV, EHV is 132KV, 220KV and 400KV and UHV is 800KV and 1200KV
it depends on the specification,,,,,,in saudi arabia as per sec standards 152kv voltage should be applied for a period of one hour.
the general height is 25-27mts,the first conductor is placed 17mts above the ground and rest of conductors placing 1st-2nd is 3.1mts and 2nd-3rd is 2.6mts
Its just a matter of standard. In my area, for instance, we use 13.2 KV for distribution lines, and 69 KV / 138 KV for transmission lines.
its consist of 2 meters 1 is main meter 2 is check meter , actually this consumption was depend on CT, PT's and by this can find out multiplication factor (M.F).consumption = (check meter reading KWH)*M.F ------1Ex for M.F cal: system-C.T=200/1A, P.T=132Kv/110V,Load- C.T=100/1A, P.T=132Kv/110v.M.F=System C.T*P.T/Load C.T*P.Tthere fore (200/1*132/110)/(100/1*132/110) = 2.-------2Sub 2 in 1 then u got consumption.
These are the nominal voltages used by the UK's distribution system, although (to comply with European Harmonisation requirements, 415 V has now been 'replaced' with 400 V. Incidentally, the symbol for the volt is a capital 'V', not a lower-case 'v'.
132kV substation is part of transmission and distribution of power in which the transmission voltage is 132kV. The substation is for stepping down or stepping up of the voltages to the required voltage. the substation also serves as a place where the transmission lines can be isolated, controlled and monitored. The substation consists of different equipment that is used to regulate, monitor and distribute the required power.Another AnswerIn the UK, 132 kV voltages are considered to be the lowest transmission voltages. Other transmission voltages are 275 kV and 400 kV. A '132-kV substation' is normally one in which this voltage is stepped down to a primary distribution voltage, usually 33 kV but, sometimes, 66 kV. As the previous answer points out, substations contain transformers, switchgear, busbars, and protection equipment.