0
What is the fabricated pipe and pipe-fitting industry dependent on?
Wiki User
∙ 13y ago
The U.S. fabricated pipe and pipe-fitting industry is strongly dependent on the health of the domestic construction industry, which, after enduring rough economic conditions in the late 1980s and early 1990s, rebounded in the mid-1990s.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is a heat no on pipe?
Used for inspection. Heat numbers make it possible to trace pipe from spools fabricated on a job to material documentation from a given melt. The matching documents will tell when and where the pipe was made, the material used and the pipe grade etc.
What is the difference between elbow and bend in piping?
" All bends are elbows but all elbows are not bends." Infact, the pipe is bent to form an elbow. Elbows are pre-fabricated and are firm in design. There are issues with bends since the tickness at the bend radius reduces as we bend the pipe. Sharp bends are normally called Elbows. Bends typically have a minimum bending radius of 1.5 times pipe radius (R). If this bending radius is less than 1.5R, it is called Elbow. Reference to any international / industry standard need to be traced. 1.5, 3 & 4.5 R are the most common bending radii in industry.
What is the weld hardness in welded pipe?
The answer is entirely dependent on the material/s you are welding. Consult ASME for your specific application.
What is the effective life of the GI pipe and fittings?
Gi pipe is climate dependent. Someone who lives on the coast with Gi pipe will find that their pipes will deteriorate quicker than someone who lives more inland because of the higher salt content in the air, the Gi pipe rusts. Also burying Gi in the sand or installing the Gi pipe in concrete also doesnt allow the pipe to breath.
Indian standard for pipe line color code?
what is the color code for all the pipeline used in standard hotel industry
How do you Pipe fit?
It can be a single word "pipefitting" (done by pipefitters and plumbers). It also appears in the two-word form in some sources.
How do you spell pipe fitting?
It can be a single word "pipefitting" (done by pipefitters and plumbers). It also appears in the two-word form in some sources.
What has the author Vern E Hase written?
Vern E. Hase has written: 'Marine pipefitting' -- subject(s): Marine engineering, Pipe fitting
What does run and travel mean in pipefitting terms?
the terms are part of the offset dimensions: set=perpeendicular distance run=linear distance Travel=Hypotenuse of the 2 dimensions (or true length) for further info on this and other pipefitting resource : www.pipefitter.co.uk
How do you calculate the size of the pipe for water flow?
Most plumbing or pipefitting suppliers have charts that show what size pipes you need to provide the proper flow rates at various pressures.
What is a heat no on pipe?
Used for inspection. Heat numbers make it possible to trace pipe from spools fabricated on a job to material documentation from a given melt. The matching documents will tell when and where the pipe was made, the material used and the pipe grade etc.
What is the difference between eccentric and concentric pipe intersection in oil and gas industry piping?
Let me know about the usage of Eccentric and Concentric pipe intersection in oil and gas industry? What are the major differences and concerns about Eccentric and Concentric pipe intersection in oil and gas industry?
What is the manufacturing process of seamless pipe?
fertilizing industry
What is khurras?
Khurras (mouth/ inlet of rainwater pipe on the roof) were fabricated in such a way to prevent clogging during rain. This doesn't allow sudden clogging.
What is rtr pipe?
Reinforced Thermosetting Resin Plastic (RTRP) Pipe.
What is the difference between elbow and bend in piping?
" All bends are elbows but all elbows are not bends." Infact, the pipe is bent to form an elbow. Elbows are pre-fabricated and are firm in design. There are issues with bends since the tickness at the bend radius reduces as we bend the pipe. Sharp bends are normally called Elbows. Bends typically have a minimum bending radius of 1.5 times pipe radius (R). If this bending radius is less than 1.5R, it is called Elbow. Reference to any international / industry standard need to be traced. 1.5, 3 & 4.5 R are the most common bending radii in industry.
What is the colour code in indian standards for pipe lines in automobile industry?
What is colour code for Poly vinyl acetate pipe line
