0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Draw a flow chart to calculate simple interest with 10 percent rate if time is greater than 2 yrs otherwise calculate simple interest with 5 percent?
Draw a flow chart to calculate simple interest with 10% rate if time is greater than 2 yrs otherwise calculate simple interest with 5%.
Why does the small intestine increases after death by 50 percent?
Because gases can build up and nothing will flow through it because the life has gone out of the body.
A patient is prescribed 0.4 percent lidocaine infusion to run at rate of 4mg min for 30 minutes What is the flow rate in mls hr?
30ml/hr
What is the term used for a common point in a circuit with the lowest electrical potential?
AMPERE - A unit of measure for the flow of current in a circuit. ... the same direction along a conductor from a point of high potential to one of lower potential​.
What is the difference between a stock variable and a flow variable?
A stock variable is measured at one specific time, and represents a quantity existing at that point in time (say, December 31, 2004), which may have accumulated in the past. A flow variable is measured over an interval of time. Therefore a flow would be measured per unit of time (say a year). Flow is roughly analogous to rate or speed in this sense
What sterling silver to use for soldering jewelry?
Typically one solders sterling silver with silver solders. There is not a solder called "sterling solder." You can choose from an array of silver solders ranging from easy (extra soft) through hard. Soft solders have lower silver content and melt at a lower temperature. Hard solders have higher silver content and flow at higher temperatures. If you are doing multiple solder joints on a single piece of solder you will need to use several grades of solder. However, if you are just creating a single solder joint than it is best to use a soft or medium solder.
What is a solder reel?
A reel of solder used for joining electrical circuits together on circuit boards. Solder is made of a mixture of tin and lead and sometimes has has flux (a form of acid) in the core of the solder to ensure a clean surface for the solder to flow into.
Is solder a lead alloy?
Most commonly, but antimony is another basic component of some solders. The European Union, China, and California are areas where lead solder is banned in consumer products. Tin-lead solders were most often used because they are easily melted and inexpensive. Lead-based solders have a few problems which are reducing their popularity: - Environmental concerns about e-waste - Worker safety concerns for people who constantly work with solder - The low melting point, which is not suitable for modern microprocessors Any metal which is melted to bond to another metal is a solder. Silver solder is used to repair silver jewelry, and gold solder to repair gold. Silver solder is also used in food-grade plumbing. Drinking water is soldered with lead-free solder (but lead was used in nearly all plumbing soldering until the late 1980s).
How do solder copper pipes with water in them?
That cant be done because as long as there is water in them the temperature of the pipe wont go up enough to allow the solder to flow. you have to remove the water.
What is the purpose of core in hollow solder wire?
To facilitate the soldering process, a chemical material called flux can be used to remove oxidation from the surface, keep the air from oxidizing the surfaces during soldering, and to aid in the flow of solder through the joint. Fluxes can be found within the solder (cored solder) or separately in paste form.
What is cold flow?
It is a term used when soldering with a soldering iron. It means that the solder is not completely up to temperature to make a proper joint. A good solder joint is very silvery in colour and shines when it is done right.
Why is flux required for soldering?
flux acts as a wetting agent in the soldering process, reducing the surface tension of the molten solder and causing it to better wet out the parts to be joined.
What is flow of electricity?
flow of electrcity is nothing but the flow of electrons from one point to another point ina conductor
What flow of electricity?
flow of electrcity is nothing but the flow of electrons from one point to another point ina conductor
how do weld GI pipe to GI pipe?
A GI pipe is welded to a GI pipe by using solder and flux. The pipe is heated up, flux applied, and then solder allowed to flow into the joints to create a secure bond.
What is soldering wire?
Solder is a group of metallic alloys that melts at a relatively low temperature and is generally used to connect other pieces of metal together. The low melting point makes it useful for some applications, especially electronic circuitry and some plumbing applications, though it should be noted that plumbing solder is a different alloy than electronic solder and plumbing solder has little or no lead to minimize lead exposure to the people who drink the water. Having described what solder IS, soldering wire is just that, its a wire that is made of solder. Solder wire is useful when working on electronic circuits since it allows the user to control how much will be put on an electronic connection. Solder wire comes in several sizes, as well as with or without a flux core. Flux is a material (usually either acidic or rosin) that encourages melted solder to flow onto other metals, usually copper, iron or brass. Other types of solder are available for use on materials such as aluminum, but solders should match the application to match the type of metals you are joining.
What is the function of the flux in soldering?
Flux can be in many different forms. it can be in the solder, it can be in a soft form like butter, or it can be in a pen like a tide stain stick. it is used on the solder iron and on the thing you're soldering to make a good surface for the solder to stick to. Basically it makes soldering easier, it can be done with out it.
