answersLogoWhite

0


Best Answer

Bottom hole Temperature is 85F + (0.015 x Depth in feet)

User Avatar

Wiki User

11y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is the formula for bottom hole temperature in oil well?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Why is the bottom hole on your well pump capped off?

Depends on type of pump.


Can you use a deep well jet pump as a shallow well pump by plugging the top hole off and just using the bottom hole in the pump?

yes


Can you use a deep jet well pump as a shallow well pump by plugging off the top hole and only using the bottom?

yes


A girl went to the well to get a bucket of water there was a hole in the bottom of the bucket but she made it home with water in the bucket how did she do it?

There was a bucket at the well that she picked up and used


What is the temperature during a thunderstorm?

Depending on many different conditions the temperature on the ground during a thunderstorm can be well below freezing (<32F) to over 100F. Inside the thunderhead clouds themselves the temperature at the bottom is above freezing but at the top the temperature is often well below freezing.


How do you play E on the recorder?

Low E: Put your fingers on all first five holes and the hole at back as well. High E: Put your fingers on all first five holes and HALF the hole at back.


What do you call the bottom of a well?

bottom of a well


What is it like being at the bottom of a hole?

Similar to being in a well, dark with light above unless it is either too deep or too dark to see the light


How do you get water from an aquifer with a well?

An aquifer is a layer of water in the soil. A well is a hole drilled into that soil that will permit water to fill the lower levels of that hole. Water is then pumped from the well. A pump connected to a metal pipe is lowered to the bottom of the well. The pump is generally operated by a motor located at the surface. The pump forces water from the aquifer up the pipe and to the distribution point at the surface.


What do you need to do to prepare the soil for a holly bush?

Excavate a hole twice the size of the rootball. Break up the bottom of the hole and incorporate some compost or other fibrous material. Scatter some fertiliser on the loose soil place the holly in the hole so that the soil level is the same as the soil mark on the bush. Fill in the hole and firm the soil down with your feet water well and stake. Keep well watered until you are sure it is growing.


If you add water in a bottle than add oil and punch a hole in the bottom would the water taste like oil?

Well i just tested it myself interestingly when i punch a small hole in the bottom of the bottle and taste the water it did not have any taste of oil in it not only that the bold that i used to sit the bottle in so far doesn't have any trace of oil in it.


What is a thermometric well?

Ans. Thermometric Well Fig. 3.6 shows an arrangement which is used to measure the temperature of gas flowing through a pipeline. A small tube called thermometric well is welded radially into the pipeline.The well is partially filled with some liquid and the thermometer is immersed into this liquid. When the temperature of the gas flowing through the pipeline is higher than the ambient temperature, the heat flows from the hot gases towards the tube walls along the well.This may cause temperature at the bottom of well to become colder than the gas flowing around. Obviously the temperature indicated by the thermometer will not be the true temperature of the gas. The error in the temperature measurement is estimated with the help of the theory of fins.The protective tube (well) can be considered as a hollow fin (internal diameter d,thickness ö and length 1), and the temperature distribution obtained by using the relation applicable to a fin with tip insulated:where is the temperature of the pipe wall, ta is the temperature of hot gas or air flowing through the pipeline, and is the temperature at any distance x measured from pipe wall along the thermometric well.If x = 1 then,where t1 is the temperature recorded by the thermometer at the bottom of well and represents error in temperature measurement.The perimeter of the protective well P = and its cross-sectional area Therefore,then,