0
What else can I help you with?
What is the different between gG fuse and aM fuse and FF fuse and gR fuse and etc?
gG FUSES IS FAST ACTING BUT THE mA FUSES ARE TIME DELAY FUSES
What does a 4a 250v slow blow fuse normally LOOK LIKE and Is it supposed to look like a fast blow with a bead of solder in the middle?
The information of, if the fuse is a slow blow or not, is printed on the fuse. In electrical terminology it is known as a time delay fuse. Smaller glass envelope time delay fuses will have a spring mechanism that can be seen through the glass envelope. Time delay fuses are used in circuit that have a high inrush current when the device is first switched on. A good example of this would be an electric motor. The bead of solder on the end of glass fuses is how the spring is supported to the end cap of the fuse.
What is time delay valve?
time delay valve is nothing but when a certain pressure is reached the valve will actuate it when the delay reaches
Fuse size for 7.5 HP 3 Phase 440 Volt Motor?
The electrical code states that a 7.5 HP 460 volt three phase motor draws 11 amps. For fuse sizes, non time delay - 30 amps, time delay type D - 20 amps and if using a breaker it will be 30 amps. Minimum wire size is #12 and the maximum setting of overload devices will be 13.75 amps
How do time delay grenades work?
time delay grenades work by pulling the pin to active its explosion then throwing it immediately before it blows your hand off!
Where do you used a time delay fuse?
we use a time delay fuse at furnace area where heaters are used ect,
What is the difference between a slo-blo fuse and a time delay fuse?
There is no difference. Slo-Blo is just a trademarked name for a time delay fuse.
Why use a Time delay fuse versus non time delay?
A time delay fuse will allow for a temporary spike in the current (up to 100 or 200% of the fuse rating), such as when starting a motor. A regular (non-time delay fuse) will not allow for any spike over the current rating of the fuse. If you have a motor that pulls 2 amps while running, but pulls 6 ampls while starting, then you will want to use either a 6 amp non time delay fuse, or a 2 amp time delay fuse. If you are talking about pyrotechnics, a time delay (properly called a slow burning) fuse will give you more time to run for cover.
What is the difference between a fuse and a time delay fuse?
A time delay fuse will not blow at the first sign of an overload. It will delay blowing just long enough to allow a motor to start or a compressor to startup.
What do the letters mdl stand for on a fuse?
Time delay fuse.
Can you use a time delay fuse in your central air conditioner of the same amp rating?
Yes, and you should use a time delay fuse.
Should you use time delay fuse when installing a range?
No, use a standard fuse.
What does T stand for in a fuse labeled T 2A 250V?
time delay
What is a time delay fuse used for?
A standard fuse will blow in just milliseconds when excess current flow or a short is detected. A time delay fuse on the other hand may take 5-10 seconds to blow under the same conditions. You would want to use a time delay fuse in a device that uses lots of current at startup but then uses less after it is started. An electric motor or compressor is an example.
What is the different between gG fuse and aM fuse and FF fuse and gR fuse and etc?
gG FUSES IS FAST ACTING BUT THE mA FUSES ARE TIME DELAY FUSES
Can time delay house fuse replace an ordinary fuse?
You could, but it would be safest not to. A time delay fuse will allow for a short (12 seconds or less) spike in the current (up to three times the rated current for the fuse). This happens when you start up a motor, or a compressor, etc... If you were to replace a regular fuse (say 2 amp) with a time delay fuse (also 2 amp), then instead of breaking the circuit at 2 amps, the circuit will go 12 seconds at 6 amps before shutting down. This could easily start a fire, so for your safety, it is best to replace a fuse with the exact same kind that came out of it.
What makes a time delay fuse burn out?
Short in circuit wiring or circuit overloaded.
