0
The purpose of splicing wire is to extend the wiring to further the distance of the circuit. A main feeder from a distribution panel can be spliced to supply voltage to more that one circuit. This is a money saving procedure as each separate circuit does not have to be brought back to the distribution panel. In underground direct burial feeds that have been dug up by a back hoe, a splice is the only way to restore power short of installing new cable. Special underground splice kits are used to restore the insulation factor of the cable, which usually leaves the cable with a better insulation factor at the break than that of the original cable insulation.
Wiki User
∙ 12y ago
Wiki User
∙ 6y agoSplicing a method to connect two wires. If the slicing is not correct, it may lead to localized heating, burn out, break in the circuit, disconnection of the two wires.
Add your answer:
Earn +20 pts
What is electrical cable splicing?
Splicing is the joining of cable , rope , wire , or any other type of strand-like material.
Can you junction box 8ga wire with 10ga wire?
There is no restriction on different size wires being spliced in the same junction box. If your question involves splicing 8ga. to 10ga, this also is not a problem so long as the circuit allows for 10ga wire.
How much electrical wire loop be left on wires before entering the outlet and switch box?
From where the wires enter the junction box there should be 6 inches of wire left for the electrician to complete the splicing of the circuits. NM cables must be supported within 12 inches of a box. There is no loop of extra wire allowed such as you might find with data or low voltage cables. Most conduits must be supported within 36 inches of a box.
When splicing high voltage cables what is the minimum distance between splices?
30 cm
True or false stranded wire has a slightly smaller diameter than solid wire?
They should be the same but have different purposes. Stranded wire will flex easier than solid wire. And if one strand breaks there are sufficient numbers of other strands to continue the electrical current. When a solid wire breaks all connection is lost.
What is electrical cable splicing?
Splicing is the joining of cable , rope , wire , or any other type of strand-like material.
How is wire splicing related to specialization?
In the high voltage linesman trade there is a branch that just specialize in cable splicing. There is special training on different types of splicing. Mostly having to do with the equipment that is used to make the splices and cable strength after a splice is made.
What is duplex wire splicing?
for instance, breaking into a series run of cable to install a switch for a device.
Is rubber an electrical insulator and its uses?
Yes, rubber is a insulator and is used as wire insulation and is also used as tape for splicing wire connections.
Will splicing a 3 wire 240 volt compressor with a 4 wire 240 volt male end damage compressor motor?
It could if you don't get the terminals and motor wires on the correct terminals.
What does wire splicing mean?
Electrical wire splicing is the act of removing the outer shell of a wire, exposing the inside and connecting to another wire that is also spliced. This also allows you to add length to wiring.
What do you mean by splicing in electronics?
Splicing means joining in optical fibers.a process called splicing takes place to join two fibers.
What is the process called which removes introns from RNA?
RNA splicing
Can copper speaker wire be spliced with silver speaker wire?
Splicing Different WiresYes, IF the rules of proper splicing are followed, dissimilar metals can be successfully spliced.Some of those rules that I can recall at the moment include:The part of the wires to be connected by splicing MUST be clean and free of any grease, dirt, corrosion, or deleterious material.A "sound" mechanical connection MUST be made. That means either the wires properly twisted together, OR a mechanical device [connector, wire nut, or some type of terminal used].If a twisted mechanical splice is used, then the splice joint should be soldered to both "lock" the twisted splice, and to prevent the atmosphere from getting into the wire interface, causing corrosion which will degrade the current carrying ability of the splice joint.
Must bare ground wire splices or connections be in a box?
I thought so. A buyers home inspecter says the splices,connections must be in a box "as per code".
What is the procedure for splicing home service wires?
The electrical code states that any splice in a wire, the insulation over the splice has to be equal to or greater than the insulation on that of the rest of the wire. So what ever type of splice that you use make sure that you insulate it well.
How do you hot-wire a car?
WikiAnswers will not provide information that can be misused for illegal purposes.
