0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the ratio of average shear stress to maximum shear stress for a circular section?
the average shear stress is 3/4 the maximum shear stress for a circular section
Introduction of chip thickness ratio and shear plane angle during machining?
shear plane angle is Eric siangco + hulian lastontas = shear plane angle
How does shear strength of fine sand effect by void ratio?
Shear strength of fine sand is determined by the angularity of the sand particles, the grading of the sand. These two features governs the critical state shear strength parameters of the sand. Density, however, dictates the peak shear strength of the sand. i.e. the denser the sand, the higher the peak shear strength. But the critical shear strength remain the same. The denser the sand, the lower the void ratio. Shear strength of fine sand is determined by the angularity of the sand particles, the grading of the sand. These two features governs the critical state shear strength parameters of the sand. Density, however, dictates the peak shear strength of the sand. i.e. the denser the sand, the higher the peak shear strength. But the critical shear strength remain the same. The denser the sand, the lower the void ratio.
Which types of soils the vane shear test is applicable?
how use the result of vane shear test
Why is the maximum bending moment of a structural member as the point of zero shear?
Shear is the rate at which bending moment changes or shear is its derivative with respect to span. The integral, bending moment, goes through a maximum when shear goes from positive to negative or vice-versa.
What is function of drop panel?
Drop panels are used to thicken the slab around the column in flat slabs to avoid punching shear. Since flat slabs have no stirrups shear is resisted by thickening the slab around the column to increase the concrete in shear. Beams can also be used, but generally drop panels are preferred to avoid conflicts with the electromechanical works of the structure.
What has the author Antti Hanhijarvi written?
Antti Hanhijarvi has written: 'Computational optimisation of test specimen for planar shear strength tests of wood based panels' -- subject(s): Shear (Mechanics), Plates (Engineering)
What has the author Dave Sharp written?
Dave Sharp has written: 'Novel composites for wing and fuselage applications' -- subject(s): Mechanical properties, Panels, Buckling, Tensile stress, Load carrying capacity, Shear strain, Tensile strength, Shear strength, Composite structures, Shear stress
Did that unscrupulous builder fleece the tornado victims out of hundreds of dollars by using inferior construction materials?
shear
What has the author T Nicholas written?
T. Nicholas has written: 'Determination of the complex shear modulus of a filled elastomer from a vibrating sandwich beam' -- subject(s): Composite construction, Elastomers, Girders, Shear (Mechanics)
What is the approved location of the construction joints in the raft foundation?
The best location to set the construction joint is less shear force impact. e.g:In slabs;it is better to locate between the supports.
What has the author J A Ramirez written?
J. A. Ramirez has written: 'Review of design procedures for shear and torsion in reinforced and prestressed concrete' -- subject(s): Concrete beams, Prestressed concrete construction, Reinforced concrete construction, Shear (Mechanics), Torsion 'Robust Speech Recognition and Understanding' 'Transfer, development, and splice length for strand/reinforcement in high-strength concrete' 'Experimental verification of design procedures for shear and torsion in reinforced and prestressed concrete' -- subject(s): Concrete beams, Shear (Mechanics), Testing, Torsion 'Proposed design procedures for shear and torsion in reinforced and prestressed concrete' -- subject(s): Concrete beams, Prestressed concrete beams, Shear (Mechanics), Torsion
Special form of of pre-cast walls construction in which wall panels are cast horizontally at the job site and then erected?
the common term for this type of construction is "tilt-up".
Why are open plains oceans and mountains good places for windmills?
The wind shear is lower than over forest or broken terrain. Wind shear is the difference in wind speed at different heights above ground. Little wind shear is important to have low mechanical stress on the turbine, the blades, and other construction elements.
Suggest alternative examples of modern technology that could benefit the construction organisation?
wind turbines and solar panels
Relationship between the shear stress and angle of shear?
Shear Stress divided by the Angle of Shear is equals to Shear Stress divided by Shear Strain which is also equals to a constant value known as the Shear Modulus. Shear Modulus is determined by the material of the object.
radiant heating panels?
form_title=radiant heating panels form_header=10563 What types of panels were you thinking about?*= [] Floor panels for heating [] Floor panels for cooling [] Ceiling panels for heating [] Ceiling panels for cooling [] Wall panels for heating [] Wall panels for cooling How much is the area (in sq.ft) would the system cover?*= {Select One,Less than 1500 sq ft,1500 - 2500 sq ft,More than 2500 sq ft} At which location is the radiant system to be installed?*= () Individual room(s) of existing home () New construction or addition () Entire existing home
