0
What is the value of compensating resistor needed for a non inverting op-amp circuit using 10k resistors for both ri and rf?
In a non-inverting op-amp circuit, the gain (A) is determined by the ratio of the feedback resistor (Rf) to the input resistor (Ri) using the formula ( A = 1 + \frac{R_f}{R_i} ). With both Ri and Rf set to 10kΩ, the gain would be ( A = 1 + \frac{10kΩ}{10kΩ} = 2 ). If you are looking for a compensating resistor to balance or adjust this gain, it would depend on the specific requirements of your circuit, but typically, no additional compensating resistor is needed if the desired gain is already achieved with the chosen resistors. Adjustments can be made if a different gain is required.
What else can I help you with?
Circuit diagram of a binary weighted resistor network digital to analog converter?
this network can be made by using summing amplifier + inverting or non-inverting configuration
What is the meaning of resistor?
Resistors are one of the three basic electronic components. They restrict the flow of current in an electrical circuit. Fixed resistors have a fixed value of resistance, and are used in almost every electronic circuit for lots of different reasons.
What products use Variable resistor?
Toasters and lightbulbs.AnswerA resistor is an circuit component. So, while toasters and light bulbs have resistance, they are not resistors!
How is the stepped resistor differ from the fixed resistor?
A stepped resistor, also known as a variable resistor or rheostat, allows for adjustable resistance levels, enabling fine-tuning of current flow in a circuit. In contrast, a fixed resistor has a constant resistance value and does not change. While stepped resistors can be used for applications requiring variable resistance, fixed resistors are typically used in applications where a specific resistance is needed. The ability to adjust resistance in stepped resistors offers greater flexibility in circuit design.
How op-amp can be used as adder?
An operational amplifier (op-amp) can be configured as an adder using a summing amplifier circuit. In this configuration, multiple input voltages are fed into the inverting terminal through resistors. The op-amp produces an output voltage that is proportional to the negative sum of the input voltages, scaled by the resistor values. By using feedback and appropriate resistor ratios, the circuit can be designed to add the input voltages with desired gain or weighting.
What is true of a series circuit that has two resistors?
Which is true of a series circuit that has two resistors?A.The resistors are on different branches of the circuit.B.Neither resistor has current flowing through it.C.One resistor has no voltage across it.D.Both resistors have current flowing through them.
Circuit diagram of a binary weighted resistor network digital to analog converter?
this network can be made by using summing amplifier + inverting or non-inverting configuration
Did the the total voltage across the resistors does not depend on the resistor value?
It depends on where and how the resistor is placed in a circuit. A string of series resistors will split the voltage across all them depending on their values. All of the resistors in parallel will have the same voltage across all of them no matter what their resistance is.
A circuit has a battery connected to resistor 1 and resistor 1 is connected to resistor 2 which is then connected back to the battery what can be said about this circuit?
This circuit is a series circuit, as the current flows sequentially through resistor 1, then through resistor 2, before returning to the battery. The same current passes through both resistors, and the total resistance is the sum of their individual resistances. The voltage across the circuit is divided between the two resistors according to their resistance values. Additionally, if one resistor fails, the entire circuit will be interrupted, stopping the current flow.
What is the meaning of resistor?
Resistors are one of the three basic electronic components. They restrict the flow of current in an electrical circuit. Fixed resistors have a fixed value of resistance, and are used in almost every electronic circuit for lots of different reasons.
What happens in a series circuit if one of the resistors is replaced with a resistor having a lower resistance value?
In a series circuit, if one resistor is replaced with a resistor of lower resistance, the total resistance in the circuit decreases. This leads to an increase in the overall current flowing through the circuit.
How calculated the value of resistor that is to be used in particular circuit?
To read the value of a resistor: Resistors are color coded, you can use the chart found below And how accurate the values of resistors are is their tolerance, also found in the chart
What products use Variable resistor?
Toasters and lightbulbs.AnswerA resistor is an circuit component. So, while toasters and light bulbs have resistance, they are not resistors!
How do resistors reduce voltage in an electrical circuit?
Resistors reduce voltage in an electrical circuit by impeding the flow of electric current, which causes a drop in voltage across the resistor. This drop in voltage is proportional to the amount of resistance in the circuit.
How do resistors drop voltage in an electrical circuit?
Resistors drop voltage in an electrical circuit by impeding the flow of current, causing a voltage drop across the resistor according to Ohm's Law (V I R). This results in a decrease in voltage across the resistor, allowing for control and regulation of the electrical current in the circuit.
How does a voltage divider work to distribute voltage across multiple resistors in a circuit?
A voltage divider is a circuit that uses two or more resistors to divide the input voltage into smaller voltages across each resistor. The voltage across each resistor is proportional to its resistance compared to the total resistance in the circuit. This allows for distributing the input voltage across multiple resistors in a controlled manner.
What is the total voltage in a series circuit when multiple resistors are connected in series?
In a series circuit with multiple resistors connected in series, the total voltage is equal to the sum of the individual voltages across each resistor.
