0
What size wire do you need for 440 three phase welder on an eight foot run?
Wiki User
∙ 13y ago
The wire size depends on the amperage, not the voltage. The fact that the welder runs on 440 volts does not affect the wire size!
You need to ask this question instead:
What size wire do you need for a three phase welder on an eight foot run if the nameplate amps are 45A?
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Wrought in a sentence?
What hath God wrought? The palatial estate was bordered by an eight-foot wrought iron fence.
What is a foot valve?
A foot valve is something that you eat with your foot
Where does you neutral come from single phase transformer?
In a single phase system the neutral wire is the return path of the circuit and may be near ground potential, in multiphase systems it carries the unbalanced current.In a single phase system where only one "hot" wire supplies current to the load, the "neutral" wire completes the circuit and carries the current flowing from the load back to the power station.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How much does US railroad rail iron weight in lbs per ft?
Anywhere between 75 and 175 pounds per Yard devide by three for foot weight
How tall is 3 stories?
It varies. Some have 8 foot ceiling with 1 foot floors=9 foot some have 8 foot ceiling with 2 feet floors=10 feet
Would using a 200 foot extension cord which is 6 gauge 3 wire cord on a 220 single phase welder present any problems?
Absolutely, you will have voltage drop, maybe enough voltage drop that the welder will not work <<>> To do a voltage drop calculation for the 200 foot cable the input amperage of the welder needs to be stated. At a maximum distance of 201 feet and limiting the voltage drop to 3% or less, a #6 copper conductor can deliver 37 amps on a 220 volt system. Check the nameplate on the welder to see if it falls withing the range of 37 amps input amperage. Do not use the welders output amperage.
Approximately eight cantaloupes and three oranges tall?
5 foot 3 inches
How much is eight foot three in inches?
Just multiply the number of feet by 12, then add the result to the inches.
What phase of the cycle does DNA occur?
foot
Are you healthy at 105 pounds at the age of 13?
It depends on your height. I think that you're approximately at the right weight though, if you aren't 2 foot three or eight foot eleven.
When was Eight-Foot High Speed Tunnel created?
Eight-Foot High Speed Tunnel was created in 1936.
How long is a railroad tie?
Most railroad class 1 ties are six inches by eight inches by eight foot long. Hard wood ties can either be eight foot six inches or eight foot. Crossing ties can be nine foot long Switch ties can be up to 26 feet long
How many sq feet in eight foot round table?
An eight-foot wide round table is 50.27 square feet.
Would using a 60 foot extension cord which is 6 gauge 3 wire cord on a 220 volt single phase welder present any problems?
It shouldn't. Check the nameplate for input amperage of the machine. Your #6 wire is good for 60 amps. If the nameplate amperage is below 60 amps then you are good to go.
What part of a foot is eight inches?
all of it...
How many eight foot long 2 x 4's will you need to build a wall eight feet high and twelve feet long?
Okay, this requires a little simple math and some three dimensional thinking. For the fence (wall) planks alone, you will need 55 eight foot 2 x 4's. For a simple box frame you will need another 8. 55 + 8 = 63 The problem is, the fence (wall) will not be free standing. You'll need three twelve foot 4 x 4 posts (twelve foot long, because four feet of them will be set into the ground.
If a cubic yard measure three foot by three foot how deep is it?
3 ft
