0
What would happen if a 200 amp breaker is used in a 100 amp sub panel?
Wiki User
∙ 7y ago
There are two things to think about here.
First of all a 200 amp breaker will not physically fit into a 100 amp panel. This is so designed because the panel buss is not designed to conduct 200 amps before the current is cut off. A 100 amp rating on the panel is the maximum amount of current that the manufacturer states, that can be handled safely.
Second if the 200 amp breaker is in the main panel then everything downstream from that breaker has to be rated for 200 amp conductivity. The wire size will have to be 3/0 from the breaker to the first over current device in the sub panel which will be the sub panel's main breaker. The sub panel can not be a load center but will have to be a combination panel. I doubt that the 100 amp sub panel's main breaker lugs would be large enough to connect the 3/0 cable.
Wiki User
∙ 7y ago
Add your answer:
Earn +20 pts
If an electrician have a circuit that pulls a load of 10 amps what size breaker must that circuit be protected by?
If you are talking about a breaker in a house panel then a 15 amp breaker would be used. It is the smallest amperage breaker that you will find in a house panel.
Can nm romex be used from breaker panel box to first afci outlet?
It depends on your local building code.
What do you think would happen if you put a 3A fuse in a plug used for kettle?
I know what would happen. The three amp fuse would blow. Any device that is plugged into a receptacle with out having sufficient resistance to limit the current flow will dead short the circuit and cause the breaker that feeds the circuit to trip. In this case the fuse being of a lower rating that the feed breaker the fuse will blow without tripping the receptacle's feed breaker.
What is the anti-pumping scheme of Circuit breaker?
in order to stop the repetitive closure of the circuit breakers, anti pumping relay scheme is used. i.e suppose that an operator gives a close command to the breaker(via some switch), now the fault occurs, the breaker would tend to clear the fault and open the contacts.But since the operator has given the close command, it would cause closing of breaker again and again.. so anti pumping relay is used to ensure that this does not happen!
What are the common sizes of circuit breaker panel for all electrical home?
200 amp is the most common size used in most homes.
Where would a 100 amp breaker be used?
In a residential application it would most likely be used as the breaker for the entire main electric panel or a subpanel feed.
If an electrician have a circuit that pulls a load of 10 amps what size breaker must that circuit be protected by?
If you are talking about a breaker in a house panel then a 15 amp breaker would be used. It is the smallest amperage breaker that you will find in a house panel.
What size Aluminum wire is used for ground in breaker box?
For a 100 Amp breaker panel it would be 2 AWG. For 150 Amps it would require 2/0 (2 ought) aluminum wire.
What kind of breaker would you use for a 220 hook up?
In North America a two pole breaker will be used in the distribution panel for a supply of 240 volts for a 240 volt load.
Can you put a 60amp breaker and a 50amp breaker on a 60amp subpanel just as long as they are not being used at the same time?
You can. Using these size breakers in a 60 amp sub panel might be pushing the limit for breaking the sub panels feeder breaker. The breaker feeding the sub panel will have to be no bigger than 60 amps because of the main bus bar capacity of the sub panel. It would be better to install a 100 amp sub panel and then there would be a bit of a buffer and you will have the ability to add additional small load circuits.
How do you connect 200amp from main panel to sub panel to the lug of the min panel to lug of sub panel?
Not exactly sure what your question is and you need to make sure you are in compliance with electrical code for your jurisdiction. But, generally speaking you install a large breaker (let's say 100A 2 pole breaker to power the sub panel) just as you would install any other breaker in the presently used (hot) panel, and the proper sized cable then goes from old to new and terminates on the main lugs of the new panel. Ground and neutral are usually isolated from each other in the sub panel but depends on other factors as to location of the sub panel, etc.
Can nm romex be used from breaker panel box to first afci outlet?
It depends on your local building code.
What do you think would happen if you put a 3A fuse in a plug used for kettle?
I know what would happen. The three amp fuse would blow. Any device that is plugged into a receptacle with out having sufficient resistance to limit the current flow will dead short the circuit and cause the breaker that feeds the circuit to trip. In this case the fuse being of a lower rating that the feed breaker the fuse will blow without tripping the receptacle's feed breaker.
What does QP on a square D breaker stand for?
A QP type breaker is made by Siemens for a Siemens distribution panel and should not be interchanged with Square D. A Siemens QP type bolt in breaker will bolt into a SQ distribution panel but it is up to the electrical inspector to make the call as to it being safe or not. Square D breaker types are QO and QB. You might be mistaking the QP for a QB on the breaker. The QO breaker is a plug in breaker usually used in home wiring and the QB is a bolt in breaker. QB breakers are usually specified for industrial and commercial use.
How do you install a 110v receptacle from a 3 phase breaker box if there are no neutrals in the breaker box?
If there is no neutral available you cannot, unless you use an autotransformer and derive a neutral. A panel with no neutral is called a power panel and is used to supply 240 single and three phase loads.
Where is power window circuit breaker for 1989 Toyota Cressida?
Not circuit breaker only fuses in cars that are used. Driver side kick panel 7.5a gauge fuse check it fist.
What is a sub panel?
A sub-panel is always fed from a main panel. The main panel is situated where the electrical service wiring first enters the main structure on a dwelling plot or building site.A sub-panel can be situated within the same building as the main panel or it can be in a subsidiary building or structure (such as a garage, garden shed or workshop) that is separate from the main building.More informationA sub-panel is another name for a secondary breaker box, just as "the main panel" is another name for "the main breaker-box"."Breaker-box" and/or "panel" are just alternative short names that are used instead of the full name "circuit breaker box".
