It is used in Industrial lighting.
What's the reading at the service panel? What do regular 115V outlets read at? What kind of meter are you using? Chances are you have 480/277V 3 phase power to this building. Whoever wired the outlet used a 277V feed, possibly because 240V was not avaliable. You should call an electrician, repair of this problem may involve instalation of a transformer.
wireing diadram for 277v ballast
High Intensity Discharge fixtures can use 277 input voltages. These types of fixtures have ballasts and different wattage lamps available. The fixtures are mostly used in industrial and commercial applications.
China
wind power is used for electricity in a home also it is used for hest
What's the reading at the service panel? What do regular 115V outlets read at? What kind of meter are you using? Chances are you have 480/277V 3 phase power to this building. Whoever wired the outlet used a 277V feed, possibly because 240V was not avaliable. You should call an electrician, repair of this problem may involve instalation of a transformer.
A step-up transformer increases (or "steps up") the voltage of an alternating electrical current. For example, a step-up transformer could be used to increase 120V AC to 277V AC to provide power to 277V electrical equipment in a building that does not already have a 277V electrical system.Other examples where a step-up transformer might be used include these:Using 240V AC equipment with a 120V AC mains supply.Generating high voltage for use with tubes, such as a CRT.Generating high voltage for use in electric energy distribution.
With a transformer.
No...that's too much voltage, and 277v is normally three-phase power.
It starts out with 480 Volts, which is used to power motors. 480 can be stepped down to 120/208/277. The 120 operates normal appliances, while 208 can be used for dryers and welders rated for 208. 277V is usually used for lighting circuits. 3-Phase is used in commercial and industrial settings.
277v light fixtures are more efficient to operate and less expensive to install than a 110v fixture of identical wattage. 277v light fixtures are typically installed when 480V 3 Phase primary electric service supplies a commercial or industrial facility. 277v lighting circuits are single phase circuits using one of the 480v primary phases (A,B & C) to Neutral. The higher voltage allows more fixtures per circuit using smaller conductors and longer runs typically required in warehouse lighting applications. ( Amps = Watts/Volts: 400W/277V Fixture = 1.4 Amps, 400W/110V fixture = 3.6 Amps) With 480V 3 Phase primary service, 110V Single Phase power is created using a Step-down transformer. The voltage transformation process consumes power (kWh) and the 277V fixture will consume less kWh than a 110V fixture if identical wattage, especially in fixtures with ballasts such as fluorescent or High Intensity Discharge (HID), like Sodium, Metal Halide or Mercury Vapor.
wireing diadram for 277v ballast
Answer for USA, Canada and countries running a 60 Hz supply service.Assuming you are using the same fixture, and assuming the fixture can operate on either voltage, you will get fewer amps with 208v than with 277v. However, a fixture designed for 208v will probably burn up on 277v, and a fixture designed for 277v will probably not produce any light on 208v.The two fixtures in reality are quite different. The 277v fixture is using one leg and neutral of a 277/480v 3 phase 4 wire system and the 208v fixture is using 2 legs of a 120/208v 3 phase 4 wire system.In commercial and industrial installations the 277v fixture is most common.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
There are solar thermal plants in California and Nevada
In the supply industry it refers to circuits of below 1000 volts. Common voltages used are 120v, 208v, 230v, 240v, 277v, 400v, 415v, 480v.
America
Mathematically, just divide 480 by the square root of three. Electrically, 480V refers to the line-to-line value of a three phase system. For example, measure the voltage across A-phase and B-phase and you'll get 480V. 277V is the line-to-neutral value. Measure the voltage across A-phase and the neutral conductor and you should get 277V.