0
The coolant drain plug is located on bottom corner of radiator facing engine.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
I need to drain the engine coolant from the engine block on a 1997 transport. Where is the engine drain plug located?
on the buttom of the block Can you please be more specific? Where exactly on the bottom of the block? Near what on the block?
Where are the engine block coolant drain plugs located on a 7.4L engine in a 2000 GMC K2500?
Wear is drain plug on 1997 GMC 7.4
Where is the egine coolant drain plug located on a 4 cylinder 1997 Toyota Camry?
It should be at the bottom of the radiator plus there is at least in the engine block.
Where is the coolant drain plug in a 97 Mazda Protege?
There is usually one on the bottom of the radiator.Possible AnswerI have gone to the dealer and the chief mechanic said that there is no drain plug on the 1997 Mazda protege. Sounds sketchy to me, but I can't find it either. ***Many (most I think) cars have two drains in the cooling system -- one on the bottom of the radiator and one on the engine block. You normally open both when changing the coolant because the coolant won't drain out of the block very well if you don't. I expect that the dealer and chief mechanic were answering the question "Where is engine block coolant drain plug?" I have just been crawling around under my 2002 Protege which I think has much the same engine as the 1997. Damned if I can find a drain plug on the block. Based on what you were told, I'm going to proceed on the assumption that there isn't one*** vtcodger
Where is the coolant drain plug on the engine block of a 1997 Honda Accord LX 4-cylinder?
The Coolant Drain Plug for a 1997 Honda Accord LX 4cyl is at the bottom of the Radiator on the left side, if you were facing the Vechiel. It if stock it looks like a Black Medal Wingnut, unless different Drain Plug was put in by previous Owner. The block drain is an 8mm plug next to the oil filer on a 94 Accord LX 2.2L. 94-97 might be the same. There is a 10mm plug near the oil filter also, but it contains oil... I know. I have tried to remove my coolant block drain plug but without success so far... It is torqued! hw
Where is the engine coolant drain plugs on a 1997 gmc 1500 v8?
At the under side of the radiator on the drivers side.
Where is the block drain plug for 1997 ford escort lx?
The block drain plug is on the front side of the engine. It is located directly underneath the exhaust manifold. It takes a hex wrench to open it up.
Where do you put coolant in a 1997 BMW 328i?
In the coolant reservoir in front of the engine.
Where is the drain cock on a 1997 Contour?
Drain cock for the coolant is on the lower passenger side of the radiator toward the engine bay side of the radiator. Difficult to get at, but nothing a long, man-sized screwdriver can't solve.
Where is the coolant temperature switch on 1998 Oldsmobile bravada?
My 1997 is located on the drivers side engine block towards the back above spark plugs it threads into engine and has 2 wires coming out
How do you install a block heater for a 1997 VW Golf?
drain all coolant from block and rad. remove the plug (located at the rear right hand side of the engine block). clean out the hole. put your heat coil in the hole pointing towards the 6'oclock position. tighten up the coil assembly to 25 lbs. refill collant, and start up to check for leaks.
How do you replace the thermostat located on a 1997 Volkswagen?
I have recently replaced Thermostat on my 1999 New Jetta GLS. Here is what I did and the replacement was successfull. First, the coolant has to be drained completely. Locate the drain at the bottom left side of radiator and drain the coolant from radiator. Then drain the coolant from the engine block. I did not do the second drain and got about 1 pint of coolant spilled during the thermostat replacement. Detach the hose from the thermostat housing cover at the front of engine block. Pull the metal hose clamp back over the hose. You will need wide angle pliers to loose the clamp. Reattachment during reinstallation will be more difficult. Remove the bolts/nuts and detach the cover. You will need 10mm size wrench (or Allen wrench) to do it. I got very anxious when I find out how inaccesible are the nuts. The Allen wrench would work better if I had one with the right size. Use screwdriver to gently remove the O-ring. It is recommended that you get a new O-ring. Remove the old thermostat, place the new one, then O-ring and the remaining steps are reverse of installation. Remember to close the coolant drains before refilling the cooling system - the old coolant can be reused. The coolant must be added gradually. The engine should be turned on for a while to allow the coolant to reenter all the space in the engine block and radiator.
