Dodge Ram
Oldsmobile Bravada
Crankshaft Sensors

Where is the crank sensor located on 1998 Bravada?

596061

Top Answer
User Avatar
Wiki User
Answered
2007-02-25 18:09:01
2007-02-25 18:09:01

the crank sensor is located just behind the crank shaft pully of the engine.

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


wHereis the abs wheel speed sensor located on 1998 Oldsmobile bravadaI


how many oxygen sensor are on a 98 olds bravada? i have located 2 and just want to make sure there isnt any other ones i may have missed


there is no crank sensor on a Mitsubishi 3000 gt but there is a crank angle sensor that looks just like a distributor its in the back of the engine on top between valve covers


That year did not have 1. It uses a crank sensor and cam sensor


The crank shaft sensor on a 1998 BMW 74Oil is located down near the crank on the front of a motor. It is super easy to replace but sometimes reaching the harness wire is a little bit difficult.


it is located on the topside of the crank sprocket behind the timing cover.


To change a throttle position sensor on a 1998 Bravada, disconnect the negative battery cable. Separate the wiring harness connector on the throttle position sensor and take off the sensor. Replace with new.?æ?æ


The crank sensor is located on the bottom of the timing cover under the right hand side of the water pump by the crankshaft pulley.


On front cover of engine by crankshaft pulley.


on the 1998 the camshaft sensor is in the distributor ,you have to change it....you have to change the whole distributor..the sensor is integrated. the crankshaft sensor is located on the block under the cruise control actuator


A crank shaft position sensor on a 1998 Honda Accord reads whether or not a the engine is spinning correctly. If there is a discrepancy on how the crankshaft is spinning the sensor will relay it to the ECU.


The crankshaft position sensor is located on the front of the engine inside the timing belt cover


On the 4 cylinders it is in the rear of the block. On the 6 cylinder it is in the top of the bell housing.


If the crank sensor is not working, the engine will not run.


It's on the inside of the Harmonic Balancer Pully. It shoud be blue in color


Crank position sensor is located next to the crankshaft. In order to replace it you might have to remove the timing belt. In the most models you just can remove remove the timing belt cover and replace the sensor.


crank sensor will cause car to no start cam sensor will only set check engine light kbutlrtech@yahoo.com


its behind the crank pulley on that gear at the end of the crankshaft on the timing belt side of the motor


Its on the backside of the engine, on the firewall side


It`s on the flywheel or it`s between the motor and trans and it`s on the passinger side I hope this helps




The speed sensor on a 1998 GMC Savanna is located in the engine compartment. It is on the back of the transmission.


A) On a 2.0L & 2.5L DOHC (1999 & earlier) Engines, The crank shaft sensor is mounted above the oil filter. B) On 2.4L DOHC ( 2001 & later) engines, the crankshaft sensor is mounted on the rear side of the engine block C) On 2.5L V6 engines, the crank shaft is mounted under the distributor near the transaxle housing.




Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.