answersLogoWhite

0


Best Answer
Answerif it is a 454 or an 8.1 L it is in the bottom of the timing cover by the crank pulley. You will need a 10mm socket to remove the sensor.
User Avatar

Wiki User

โˆ™ 2014-09-08 18:41:27
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Where is the crankshaft position sensor located on a 2001 Tahoe?
Write your answer...
Submit
Related questions

Where is the crankshaft position sensor on a 2001 Chevy Tahoe with a 5.3?

The crankshaft position sensor is located right above the starter, you may have to remove the starter for better visibility.


Where is the crankshaft position sensor located on 2004 chevy tahoe?

It is behind the starter. You will have to remove the starter to service it.


Where is the crankshaft sensor located on a 1996 Chevy Tahoe?

That year did not use one.


Where is the crankshaft position sensor on a 2002 Chevy Tahoe with a 5.3?

It is behind the starter, Will have to remove starter to get to it.


Where is the crankshaft positioning sensor located on a 2003 Chevy suburban 5.3L?

Same as the Tahoe behind the starter


Where is the camshaft position sensor located on a 1995 Chevy Tahoe?

That year did not have 1


Where is the Crank sensor located on a 1997 Chevy Tahoe?

THE CRANK SENSOR ON A 97 5.7 IS LOCATED UNDER THE CRANKSHAFT PULLEY BETWEEN THE PULLEY AND THE OILPAN. SLIGHTLY TO DRIVERS SIDE


Where is the camshaft position sensor located on a 1998 Chevy Tahoe?

in the distributor located on top rear of motor


Where is the crankshaft position sensor on a 2003 Chevy Tahoe with 5.3L?

It is right behind the starter and bolted into the side of the engine block. You will have to remove the starter to service it.


How do you change the crank position sensor on 1999 Tahoe with 5.7 liter engine?

To change the crankshaft position sensor of the 1999 Tahoe, you must first disconnect the negative battery ground cable to avoid accidents. Then, remove the wire harness from the sensor, disconnect the wires, and pry out the bolt. Place the new sensor in the same area, replace the bolts, and reconnect the wires. Test the sensor to see if it is working.


Where is crank position sensor located on 1998 Tahoe with 57 liter engine?

The Crankshaft Position Sensor (CKP) is located at the lower front of the engine on the engine front cover, also called the timing cover. Through a use of magnetic pulsation, the CKP sensor provides the PCM (control module) with a crankshaft position signal. The PCM uses that signal to determine the spark sequence (firing order) for each cylinder. It also uses the signal to precisely control ignition timing and calculate engine speed, etc. Hope that helps - and Blessings!


Where is the crankshaft sensor in a 2003 tahoe 5.3?

It is behind the starter. You will have to remove the starter to get to it.


Where is crank position sensor located on 1996 Tahoe 5.7?

It is on the passenger side of the timing cover that is on the front of the engine.


Where is the cam position sensor on 97 Chevy Tahoe 5.7 vortec?

It's located in the distributor under the rotor.


Where is the TSP sensor on a 2003 Chevy Tahoe?

The TSP sensor on your 2003 Chevy Tahoe is located on the back of the transmission.


Where is the speedometer sensor located on a 2003 Chevy Tahoe z71?

The speedometer sensor on a 2003 Chevy Tahoe Z71 is located in the engine compartment. It is on the transfer case.


Crankshaft position sensor location on a 99 Tahoe 5.7 ltr. Vortec gas engine?

Its right behind the crank pulley on the passenger side of the engine. You will see the wire connector going to it.


Where is the cam position sensor on a 1998 Chevy Tahoe 5.7 vortex?

AnswerThe sensor is located in the distributor on the rear of the engine. The distributor has to be pulled to be able to remove the sensor.


Where is the o2 sensor bank 2 located in a 1997 Tahoe?

Is this bank 2 sensor 1 or sensor 2?


How do you replace a camshaft sensor on a 1999 Tahoe?

The cam shaft position sensor is located under the distributor cap. You can replace this easily by undoing the screws holding on the distributor cap, remove and replace the sensor, then just replace the distributor cap.


Where is the camshaft sensor on a 1997 Tahoe?

it should be located on the timing cover on the front of the engine, just below the harmonic balancer. NEW ANSWER : Cam sensor is under the distributor cap and bolted to the distributor base plate. The crankshaft sensor is bolted in the passenger side of the timing cover.


1996 Chevy Tahoe code p1345?

Trouble code P1345 means: Camshaft To Crankshaft Position Correlation Fault


Where is the crankshaft sensor on a Chevy 5.3 liter?

The crank position sensor (for the Chevy Tahoe/Suburban/GMC Yukon/Full size trucks) is located near the back of the engine block, on the passenger side. Near the starter. Note - the crank sensor (as well as the cam sensor) can occasionally leak oil and drip down, making it appear to be a rear main seal leak. If you have a leak at the bell housing, don't automatically assume a rear main leak.


What does 1999 Chevrolet Tahoe Camshaft Position Sensor do?

A camshaft position sensor reads the location of the camshaft and sends that information the engine computer. This is needed for fuel and ignition timing.


Where is the speed sensor located on a 2004 Chevy Tahoe?

It is screewed into the transfur case.