Ford Explorer
Ford Ranger
Ford Explorer Sport
Ford Explorer XLT

Where is the ignition module on a 1992 ford explorer?

373839

Top Answer
User Avatar
Wiki User
Answered
2005-08-06 17:41:49
2005-08-06 17:41:49

Check inside the cab, on the passenger side, right side firewall. There should be a panel box there that has the cut off switch inside.

001
๐Ÿ˜‚
0
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Related Questions


Type your answer here... How do you remove ignition switch from 1992 ford explorer?



The 1993 Ford Taurus ignition module is located behind the dashboard. The ignition module, can be found on the drivers side of the dashboard.


No, the door on a 1998 Ford Explorer will not fit a 1992 Ford Explorer.


The 1995 Ford Ranger ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


where does a shift module go in at on a 1995 ford explorer xlt 4.0 2wd


You can find the Ford Focus ignition control module beneath the drivers side dashboard. The ignition control module will be above the accelerator pedal.


The 1989 Ford Ranger pickup truck ignition module is located on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


The powertrain control module on 1991 and 1992 Ford Explorer is in the right front passenger area behind the right front kick panel


The 1991 Ford Probe spark ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


How do you replace evaporator on a 1992 ford explorer?"


were is ignition drive module located in the engine


The 1997 Ford Aerostar ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


how do you remove the ignition control module on a 1988 ford f-250 pickup?


The 2007 Ford Explorer computer module is located below the dashboard, on the passenger side. The computer module is in a rectangle steel box.


You can find the module for your 2000 Ford Explorer on the firewall in the engine compartment. The module will be on the drivers side of the firewall.


My 1995 Explorer owner's manual states to have the ignition key in the off position


From 1991 to 1995 with the EEC-IV system there is an external ignition control module mounted on the radiator support in front of the battery. Remove the battery in order to change the module. 1996 and newer with the EEC-V system, the ignition control module is incorperated into the powertrain control module (PCM) that is visible from the engine compartment, in the firewall, on the passenger side.


The security module on 2002 Ford Explorer is on the passenger side, second row behind the seat belt panel.


The 1994 Ford Aerostar ignition control module is located on the firewall in the engine compartment. The ignition control module will be on the drivers side of the firewall.


The Ford Explorer relay module layout diagram can be obtained from most Ford dealerships. The relay module layout diagram can also be found at many auto-parts stores.


The 1995 Ford Explorer ECU module can be found on the outside of the air filter housing. The ECU module will be on the back of the housing.


The ignition module is mounted to the side of the distributor. It a rectangular piece.


The daytime running light module on a 1996 Ford Explorer can be found behind the bumper. It is on the driver's side of the car.


The gem module on an 03 Ford Explorer is under the dash. It is just to the left of the radio.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.