answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2014-08-27 00:36:02

Th knock sensor on a 2002 Nissan Xterra 3.3 is located on the top of the engine. It is mounted under the engine intake.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Your knock sensor is located undernesth the air intake manifold on top of the engine block. This goes for 2000-2004 xterra V6 3.3L models. Hope this helps.


Under the upper and lower intake manifolds at the back of the engine block.


A knock sensor is located in a specific area on the block or cylinder head in order to sense spark knock occuring and send a signal to the ECM to retard the timing. Relocating the knock sensor would defeat its purpose.


The knock sensor is located below the intake manifold


The knock sensor is located below the intake manifold


where is the knock located on 2001 nissan altima 2.4


The knock sensor is located below the intake manifold


if it is a v6 engine it is located underneath the intake manifold and you have to removed the manifold to replace it. if it is a 4 cylinder it is located on the back side of the engine block below the manifold


The knock sensor on a 2001 Nissan Sentra is located on top of the engine, near the exhaust manifold. It detects abnormalities in the ignition and combustion cycle.


V6 3.3L The sensor is located underneath the air intake manifold on top of the engine block. This should take an experienced mechanic about 3-4 hours to replace.


The knock sensor is located below the intake manifold


Knock sensorThe knock sensor for a 1996 Nissan Altima is located on the backside of the block above the oil filter.But before you go and change it out, run a tank of the best/hightest rated gas you can find and see if that fixes the problem. On my 1995 the Knock sensor is located under the plenum and intake manifold on top of the middle of the block.


The knock sensor for most Nissan V6 engines is located directly under the intake manifold. So to replace it, you have to remove the intake manifold. Good Luck.


newer cars do have knock sensors.. I have a 2001 xterra with the 3.3L v6 and the knock sensor is located underneath the intake manifold.. you might want to get a good repair manual or copy some pages out of one at the local library to help you figure out how to do it yourself if you plan on doing it. I'm about to change mine this weekend after i get some money together for the sensor and new intake gaskets.. this thing is making me go broke!


the Knock sensor is located behind the Harmonic balancer pulley. on the bottom sidethe sensor is $95.00 remove the lock down screw unplug and replace


center of the engine near the top. It is going to be by the heads.


can you tell me where the knock sensor is located on a 3.3l mercury villager


everyone one is telling me it is located under the intake or intake manifold, and that if must be removed..


It is located unter the intake manifold near the oil filter.


the knock sensor is located under the intake manifold, with a flash light you can see it however you have to remove the intake manifold to replace the knock sensor , also you will need to replace the intake gasket set as well!


I AM GETTING A OBD CODE ERROR FOR MY 2000 NISSAN QUEST , PO141 AND PO325 ??? HOW DO I FIX IT..


Where is the knock sensor located on impala SS


Where is the Knock Sensor located on a 1996 Oldsmobile Aurora?


where is a knock sensor located on a 96 Pontiac Bonneville


You can find a 1996 Nissan Pathfinder knock sensor picture in most auto repair manuals. Most Nissan dealerships repair centers will provide you with a picture of the sensor.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.