0
organic materials buried at the bottom of the oceans
Florine Wiza
Add your answer:
Earn +20 pts
What is a Group of joined locks on a canal called?
A group of joined locks on a canal is known as a Staircase.
Why does the river thames have locks?
There are no locks on the Thames. There are lots of locks on the Thames so that the river can be navigated. The river is tidal as far as Teddington Lock in west London.
Do dread locks happen naturally?
They can if an individual stops using conditioners and stops brushing or combing their hair. However it requires patience before dread locks become mature.
Why is iron used for locks and bolts?
to stay secure.(my computer friend :) )
How many locks are there along the Amazon River?
There are none
How do you program a 1998 Ford Escort remote?
1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. 2. Within 20 seconds press any button on first keyless remote. Door locks will cycle to confirm programming. 3. Within 20 seconds, press any button on second keyless remote. Door locks will cycle again to confirm programming. 4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
How do you program a keyless entry fo your Mazda tribute?
Using the drivers side switch, cycle the power door locks LOCK, UNLOCK, LOCK, UNLOCK. Cycle the ignition from OFF to RUN eight times within 10 seconds, ending in the run position. The power door locks should cycle to indicate program mode, vehicle is ready to accept remotes. Press any button on the remote, once again the locks will cycle to indicate a successful program. Turn the ignition off to exit the program mode.
What is deadlock and How can it occur in a distributed database systam?
It is when two processes are waiting for something and unable to continue. For example, if you have process A which needs a lock on database X and Y but only has a lock on database X while there is a process B which needs the same locks but only has a lock on database Y, then the 2 processes could potentially wait forever if they are unwilling to let go of their existing locks.
What could be causing the door locks to cycle on a 98 Pontiac Montana?
I had a 1999 Montana in which the door locks would cycle from lock to unlock, also when I turned on (if I remember the right turn signal). Took to dealer and they diagnosed the BCM (body control module) bad. I did NOT have them replace it due to cost. The problem was a bad ground connection for the BCM.
Programming instructions Lincoln navigator key fob?
1. Close all doors and then open drivers door and press the UNLOCK button on drivers door panel while door is open and insert key in ignition. 2. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. 3. Within 20 seconds press any button on first keyless remote. Door locks will cycle to confirm programming. 4. Within 20 seconds, press any button on second keyless remote. Door locks will cycle again to confirm programming. 5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
How do you program keyless remote for 2001 Lincoln ls?
Try this: Cycle the ignition from OFF to RUN eight times within 10 seconds, ending in the run position. The power door locks should cycle to indicate program mode, vehicle is ready to accept remotes. Press any button on the remote, once again the locks will cycle to indicate a successful program. Turn the ignition off to exit the program mode.
How do you program keyless remote for a 2000 Lincoln Navigator?
Try this: Cycle the ignition from OFF to RUN eight times within 10 seconds, ending in the run position. The power door locks should cycle to indicate program mode, vehicle is ready to accept remotes. Press any button on the remote, once again the locks will cycle to indicate a successful program. Turn the ignition off to exit the program mode.
How do you reset the remote key when you replace the batteries on a 2003 silverado?
If you have one remote that is working you can hold down the lock and unlock buttons at the same time until you here the locks cycle open and close, this puts the body control module in the learning mode then you hold the same buttons down on the remote that does not work until the locks cycle again and that should do it.
How does one activate door remote transmitter for 4Runner?
1. Start with the following conditions: you are in the vehicle a. Key is out of the ignition b. Drive door is open ( all other doors are closed) c. Driver door is unlocked (other door locks don't matter) 2. Insert the key into the ignition (don't turn it) and pull it out. 3. Perform these steps within 40 seconds: a. Cycle the power locks 5 times. Use an even pace and try to go relatively fast. b. Close, then open the drivers door. 4. Perform these steps within 40 seconds: a. Cycle the power locks 5 times (same as before). b. Turn the ignition to ON then back to OFF. c. Turn the ignition to ON then back to OFF. d. Remove the key from the ignition. 5. Within 3 seconds, the power door locks should cycle (automatically) indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point. 6. Perform these steps within 40 seconds: a. Press the LOCK and UNLOCK buttons on the transmitter simultaneously for 1 second. b. Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle ( LOCK then UNLOCK) once-- indicating successful programming. If the door locks don't cycle, or cycle twice. Repeat steps 6a and 6b--this remote has not been accepted. c. Repeat steps 6a and 6b for EACH transmitter that will operate the vehicle. Including any old transmitters. 7. Close the driver door. (from a Toyota forum)
How do you program the remote transmitter for the doors on a Toyota 4Runner?
1. Start with the following conditions: you are in the vehicle a. Key is out of the ignition b. Drive door is open ( all other doors are closed) c. Driver door is unlocked (other door locks don't matter) 2. Insert the key into the ignition (don't turn it) and pull it out. 3. Perform these steps within 40 seconds: a. Cycle the power locks 5 times. Use an even pace and try to go relatively fast. b. Close, then open the drivers door. 4. Perform these steps within 40 seconds: a. Cycle the power locks 5 times (same as before). b. Turn the ignition to ON then back to OFF. c. Turn the ignition to ON then back to OFF. d. Remove the key from the ignition. 5. Within 3 seconds, the power door locks should cycle (automatically) indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point. 6. Perform these steps within 40 seconds: a. Press the LOCK and UNLOCK buttons on the transmitter simultaneously for 1 second. b. Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle ( LOCK then UNLOCK) once-- indicating successful programming. If the door locks don't cycle, or cycle twice. Repeat steps 6a and 6b--this remote has not been accepted. c. Repeat steps 6a and 6b for EACH transmitter that will operate the vehicle. Including any old transmitters. 7. Close the driver door.
How do you program a keyles remote for 2003 chey Tahoe?
you need to get in your Tahoe 1. put the key in the ignition 2. hold down the unlock button 3. continuing holding down the unlock button, turn the ignition on, then off, then on, then off again. 4. Release the unlock button(The Locks shoul lock then unlock) 5. Press the unlock and lock buttons on the remote at the same time and hold for 15 seconds if you have done it right after 15 seconds the locks should lock then unlock and your remote is programmed after this turn the key to the on position to exit program mode
How can you tell if your new vehicle has keyless remote?
Generally on an F-250, if you have power door locks and a keyless entry door pad on the drivers side door it should be equipped with a keyless entry remote. You can also put the vehicle into program mode by using this procedure: Cycle the ignition from off to on eight times within 10 seconds ending in the run position, if the door locks cycle it is equipped.
