0
Which protocol can be used to load or retrieve cisco ios images to or from a router?
Wiki User
∙ 14y ago
TFTP.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Which encapsulation protocol when deployed on a Cisco router over a serial interface is only compatible with another Cisco router?
HDLC
Where can a person find images of the Cisco 1700 router?
You can find images of the Cisco 1700 router on Techgenie, Cisco, Hypersurf, eBay or about any retailers which sells electronic computer devices. It shouldn't be hard to find at all.
Which service should be disabled on a Cisco switch or router to prevent packet sniffers from capturing information about the device?
CDP-(Cisco Discovery Protocol)
What identifies the IP address of the near side of a router?
CDP Cisco Discovery protocol identifies the IP addresss of neighbor router in a corporate network.
When does the banner display for cisco router?
whenever you log into your cisco router....
Which combination of Layer 2 protocol and authentication should be used to establish a link without sending authentication information in plain text between a Cisco and a non-Cisco router?
PPP with CHAP
Which combination of Layer 2 protocol and authentication should be used to establish a link between a Cisco and a non-Cisco router without sending authentication information in plain text?
PPP with PAP
Implementing Distance-vector routing protocol?
First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.
What are the parts for upgrading a cisco router 2500 series?
There are three major parts of the router that can be upgraded:DRAM memory, Flash Memory, and the IOS operating system that runs on it.DRAM and Flash can each be a maximum of 16 MB (try ebaying for cisco 2500 flash or memory), and IOS images can be downloaded from Cisco if you have a valid Cisco service contract.
What are some recommended books about Cisco routers?
Some recommended books about Cisco routers are: Cisco Router Configuration, Cisco Routers For The Desperate, Cisco Routers for IP Router, Cisco CCNA Routing and Switching.
On a Cisco router what does it mean when the status is administratively up but protocol is down?
Ports on Cisco routers can be enabled or disabled by the router OS. "Administratively Up" simply means that the port has been enabled by the router's OS. If a port is enabled (Administratively Up) and the protocol is down, then there is a problem with communications over that port. Problems could one of many including; bad cable on the port, the far end device is down, the protocol configurations on the two connected device ports are not configured correctly to enable communications.
Where is memory located on a Cisco router?
Inside the router's chassis.
