0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you repair a faucet stem leak?
With the faucet shut off, take the handle off and under it is a nut around the stem. There is either an O ring under the nut, a fiber washer or stem packing depending on what type of faucet it is. Replace which ever it has and that should fix it. If your faucet is a screw type, the handle turns several time when opening it, you can probably take the nut off, wrap two or three wraps of stem packing around the stem, clockwise looking down on it and replace the nut and tighten. This will compress the packing around the stem without replacing the cone washer in the nut or all of the old packing.
How do you remove a broken faucet from a pipe?
All you hace to do is un screw the faucet take the sink part off, If that dosent work then call a plumber. Or your dad to come fix it
How do you get the handle off to replace the washer on a delta faucet?
In nearly every modern faucet, there is a trim cap on the top center of the knob that is a friction fit. You should be able to get a fingernail under that trim cap and pop it off. Almost certainly you will find a Philips screw under it; remove that screw and the knob should then come off. You may need to apply some force to the knob; crud getting between knob and shaft, carried there by water, will tighten the fit over the years.
Why is there no water coming out of sink faucet in bathroom but tub faucet works?
The shut off valve under the sink, the faucet itself, or most likely, the screen in the end of the spout is plugged. If neither hot or cold is coming out, it is kind of unlikely both shut off valves and both sides of the faucet would go bad at the same time. The screen being clogged would stop any water from coming out. The screen just unscrews out of the spout.
How do you fix a leaky faucet?
Fixing a leaky faucet is often a simple matter of replacing the rubber seat and the packing. (Note: This does not apply to ball type faucets.) * Turn off water to the faucet at the valve under the sink. * Open the faucet and make sure the water is actually off. * Remove the handle. This varies from faucet to faucet, but most often there is a screw under a cap. * After removing the handle you should see a nut around the shaft of the valve. Remove this nut. * Remove as much of the old packing that was between the shaft and the nut as you can. * Using the handle, unscrew the valve core from the body of the faucet. Turn it in the direction you would to turn the faucet on. * At the bottom of the valve core you removed should be a rubber seat held in by a screw. Remove this. * Take the valve core and rubber seat to the hardware store to get a new rubber piece. Also get new packing. Without packing the faucet will leak under the handle. The old packing cannot be re-used. * Assemble the new rubber seat into the valve core. * Clean any old packing off the valve core and the nut. * Screw the valve core back into the faucet body. * Wrap a few turns of packing onto the valve body. Hand tighen the nut back on. * Do not install the handle yet. * Carefully turn the water back on. You should be able to turn the water fully on and off. If the faucet leaks at the valve stem, tighten the nut until it stops. Do not overtighten the nut as it will make it difficult to remove later and will make the faucet handle stiff. * Re-attach the handle. There are many different kinds of faucets or taps. This might apply to yours. *Turn off the main stopcock so the water won't pour out when you remove the tap/faucet. *Start with the top. Is there a little nut or screw you can remove to separate the handle? If there is you can remove that. You might have to hit the handle upwards or outwards with the handle of a hammer. Try not to damage anything. Even if you can't get the handle off, you might still be able to continue below. *You should then be able to unscrew something. It might just be a cover. You might need a stilson wrench for this. Sometimes the cover is on a spring that you can pull forward to expose the nut behind. *Then there might be a nut to unscrew which will remove the whole front of the faucet or tap. You WILL need a wrench or shifting spanner for this. *Pull out the valve with your fingers. If it is worn and leaking, you should replace it. A worn valve is the most common problem with leaking taps. *Then put everything back. Unless you are throwing away the old faucet/tap and replacing it with a new one. *Make sure you can turn the front handle before you tighten up the back nut. *Turn on the main stopcock. *Clean up all the dirt and muddy water from the floor. *Take a shower to test it before you tell everyone else of your magnificent achievement. turn off the water.. OR! better yet.. call a plumber Replace it. Replace it. That's easy. You need to replace the faucet washer. it's fairly simple to do, just make sure you turn off the water under the sink before you start taking the faucet off. Any knowledgeable hardware store employee should be able to assist you. Replace the rubber washer inside the faucet.To do this you must turn off the water to the faucet; usually this means turn off the city water supply to the house.Remove the handle, expose and remove the old washer.Take both to plumbing supply and obtain replacement washer if none on hand. Install and then turn on the water.turn water off at sink, remove hoses, remove nuts under sink [on faucet]remove faucet, clean area, replace with new one,[don,t forget to put rubber gasket under it] install new nuts, tightenattach water lines, turn water back on. go to lowes or home depot and have someone in the plumbing dept.walk you thru the process and then decide if you really want to try it on your own. its not rocket science but its not easy for the average joe either. I could describe it all for you but the above method is way better for you!! check the washer or the o ring, it may need replacing == Answer== Any faucet is easy to fix if you have the right tools, parts and can get the faucet apart. It is not always easy to have all of the above. I would call a plumber. unscrew it or pull off. You can tell the difference if it has a lock screw under the faucet. Pay attention to sealant. When replacing make sure the pipe is the correct length and size for your replacement faucet.
How do you correct water faucet handles that are on when in the outward position?
I assume the handles are the quarter turn type. If you turn the into the bowl to shut them off, it may be that the handles are just set on the stems wrong. If this is not the case, the cartridge in each side is in backwards. Shut the water off, take the handle off and the ring under the handle that holds the cartridge in. Pull straight up on the stem, pulling the cartridge out and rotate the whole cartridge 180 degrees and reinstall. There should be two small notches in the body of the faucet that line up with bumps on the cartridge.
Why do your tub faucet handles turn completely around to turn the water flow on and off?
The valves were installed improperly.
How do you stop squeaky bathroom sink faucet handles?
You take them off and renovate the interior seals and grease the shaft.
How do you fix a kitchen dripping faucet?
By replacing parts as needed depending on the type and brand of faucet It's possible that the gasket needs to be replaced, which is quite easy to do. Turn off the water source (under the sink) before you begin, though. Then remove the faucet handles and replace the gaskets. You can remove the faucet handles to see what size and type of gaskets you need first, or you can purchase a packet of assorted size and types of gaskets at any hardware store, in which should be the type your faucet uses. And don't be afraid of trying this on your own, it is much easier than most people think, and much cheaper than paying a plumber to do it for you.
How do you Repair a leaky delta shower faucet?
Turn off the water. Not sure if you have single or double handles. Pry plastic cap off handle. Use Phillips to unscrew handle. This should allow you to remove handle and the wallplate that conceals hole into wall. Unbolt faucet, keep track of parts. If you have old double handles, probably time to consider replacing both. Take the valve to Home Depot or the like and find EXACT replacement. Also get some white teflon tape to wrap the threads before screwing valve back in. Re-assemble , do not put handle on before you test for leaks. Use flashlight and make sure valve is in off position when you turn on water source. Then test the valve on and off w/ handle.
When doing DIY how would one install a faucet lamp?
Take the lamp faucet ring out of the package. Clean the faucet opening. Using pliers twist the lamp ring onto the opening of the faucet clockwise. Once it is tight, turn on the water. The light should be activated and the water will change colours. Turn the water off. This should turn the light off.
What is the use of faucet?
Please turn off that faucet!
How do you remove a faucet assembly that has the handles and faucet all together?
From underneath. There are two different types. There will either be a large nut on each side where the water lines attach or there will be a horseshoe shaped plate in the center that is held in place by one smaller nut. Take the supply lines off and remove the nuts that hold the faucet in place and lift it up.
How do you use the word faucet in a sentence?
The faucet drips even when the water is turned off.
How do you get all of the light switches to be in the down position for off when you have more than one switch for them?
Three way switches do not have a up-on down-off position. With the lights off, reposition the switches so that the handles are all down. This is the start position and depending on how you enter the room and turn on the lights certain switches will be left up when you leave the room. That is just the design of the switches and for the asthetics of the look, all handles down the lights will be out.
Why does my New faucet makes clunking noise?
There was air in the line. When you turn off the water with the faucet running make sure you turn it back on with the faucet open. That will release any air caught in the lines. That faucet shut with one on a lower floor on and restoring water does not work. Fast and easy. 1. turn on affected faucet 2. shut off water 3. turn water back on 4. faucet should be running smoothly now
How do you replace the valve in a Moen shower single handle faucet The faucet was installed in 2004. When you turn the handle to the left for hot the water stops. Hot water is present in the sink?
Turn the water off to the faucet. Remove the handle. The top of the faucet should unscrew to get to the ball valve. Replace the valve and gaskets then reassemble the faucet.
