0
they work parallel to power generating turbines. The only difference between prds and turbine is that prds give only process steam by simply reducing the pressure of incoming steam while a turbine generates power out of that pressure reduction, and also give left out steam as process steam.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Difference between plant heat rate and turbine heat rate?
The turbine heat rate of a steam turbogenerato is the ratio of thermal input: power generated. It is often expressed in kJ/kWh. The efficiency of the turbogenerator is simply calculated from this. The plant heat rate is the ratio of fuel energy into the plant: power generated. It is greater than the turbine heat rate, because not all of the fuel's thermal energy can be captured by the boiler, and also power station services such as fuel handling, flue gas cleaning etc consume power. Consequently, more fuel is needed for each unit of useful net power produced. Plant heat rate is often expressed in kJ/kWh or Btu/kWh. The fuel energy input used in the plant heat rate calculation may be on a higher heating value (HHV) or a lower heating value (LHV) basis, and the plant power output, although usually on a net (net of plant own consumption) is sometimes on the basis of that at the generator terminals. Whatever is used should be made clear, but it often is not.
What metals are used in a nuclear power plant?
i dnt no i dnt no
What PDMS stands for?
Plant Design Management System. This softwere is used for 3d designing of offshore platfroms, refineraires, chemcial plant, power plant etc.
What are the differences between a coal power plant and a hydroelectric power plant?
Coal is used in furnaces to heat water in a boiler to superheated (above 100 degrees Celsius) temperatures, and this steam is used to drive a turbine which, in turn, drives an alternator. A hydroelectric plant uses the vertical fall of water to drive a water turbine which drives an alternator.
What is full form KKS code used in the power plant equipment codification?
Kraftwerk-Kennzeichen System
How is thermal power plant is used?
Electronics are used in thermal power plants when the power from the thermal power plants are transferred to a storage source. There, electronics comes in.
How does a reactor work on thermal power plant?
Reactor is used for distilling water in thermal power plants.
Why prds used in power plants?
they work parallel to power generating turbines. The only difference between prds and turbine is that prds give only process steam by simply reducing the pressure of incoming steam while a turbine generates power out of that pressure reduction, and also give left out steam as process steam.
Which is the main fuel is used in Kayamkulam Thermal power station?
The Kayamkulam Power Plant, in Kerala, India, is a 350 MW Gas Fired Plant.
Which type of alternator used in thermal power plant why?
Turbo Alternators are used in thermal power stations because of the steam energy to mechanical energy conversion turbo alternator is more effitient
Furnace used in thermal power plant How this furnace works in heating the boiler?
A Furnace works by heating the power plant with the fuel provided you idiot... how else do you think it works??
How is electronics used in thermal power plants?
Electronics are used in thermal power plants when the power from the thermal power plants are transferred to a storage source. There, electronics comes in.
Why is hydroelectricity used more than thermal electricity?
The cost of production of electricity from a thermal power plant is more than that of the hydroelectricity so the later is more used if both the source are available.
What is a cogeneration power plant?
This means a plant that produces electricity and also thermal energy for district heating or something similar in an industrial plant. Gas turbines are used for such plants, the exhaust gases are still hot enough to provide useful thermal energy.
What are the raw materials used in thermal power plants?
coal is used as a raw material in thermal power stations
Why guard relay is used in power plant?
A relay in power plants comprises three components namely voltage relay, thermal relay and current relay. It is used to power up an industrial equipment.
What is a full form of prds in a boiler?
PRDS stands for Pressure Reducing & De-Superheating. The outlet steam from turbine will be used mainly for generating power and also for other industrial processes (e.g, in Textile industries for heating etc.). For industrial processes, the outlet steam from turbine will not be useful because of high temperature and very high pressure. By having a PRDS line in boiler, the temperature and pressure can be reduced by means of spraying using a control valve.
