Want this question answered?
A Bunsen burner is not made of pyrex, it's metal. Usually a beaker or flask made out of pyrex glass is heated by the flame from the Bunsen burner.
It is to prevent direct contact of the glass with the flame of the Bunsen burner. This lowers the possibility of the glass shattering when being heated Read more: What_is_the_purpose_of_the_wire_gauze_placed_over_a_bunsen_burner
evaporating dish and watch glass
A wing top is an accessory that can be used with a Bunsen burner to provide a broad flat fan flame.used to bend glass
you don't have to!The above answer is dangerous and incorrect:You turn off the burner before the water evaporates so the glass will not shatter and spray glass shards and dangerous chemicals all over the lab. You should because then it will be so hot around 90-100 degrees and it can burn you
A Bunsen burner is not made of pyrex, it's metal. Usually a beaker or flask made out of pyrex glass is heated by the flame from the Bunsen burner.
It is to prevent direct contact of the glass with the flame of the Bunsen burner. This lowers the possibility of the glass shattering when being heated Read more: What_is_the_purpose_of_the_wire_gauze_placed_over_a_bunsen_burner
A heat diffuser is used to diminish the concentrated heat of the flame of a burner and thus prevent glass from breaking due to thermal stress.
Pyrex is a common brand of lab glassware, it's made from borosilicate glass
evaporating dish and watch glass
The clay triangle is used to hold a crucible while the crucible is heated.
as far as i know, its a beaker... sadly my school thinks bunsen burners are too dangerous so i don't know for sure
A wing top is an accessory that can be used with a Bunsen burner to provide a broad flat fan flame.used to bend glass
A beaker is basically a glass cup with numbers on the side.It is used to measure water with. You might use it to heat water under a Bunsen Burner.
The little white one? It's called an evaporating dish that you put your items and water in and let it evaporate over the Bunsen burner.
Bunsen burners are a fire hazard and should not be left unattended. However, accidents can occur even when the burner is off. Check the tubing connecting the gas line to the burner to be certain there are no cracks and it is secure. If the tubing is dislodged and the gas line valve is not off, gas will fill the room creating a potential explosion situation. This has happened. There are safer alternatives to the classic Bunsen burner. A Flame Boy or a Touch-o-matic burner eliminates the issue of a constant flame. A bacticinerator can be used to sterilize plating loops. There are also glass bead sterilizers that may be used.
Turning on the burner safely:1. Turn the gas on at the source of the gas line. This can typically be found where the hose fits over the gas line that sticks out from the wall. You will want to turn it on until you can hear the gas flowing smoothly through the hose.2. Turn on the burner slowly. Once you hear the gas, you can light the Bunsen burner. Keep your fingers as far away from the flame as possible. Depending upon the flint you are using, be it a match or a flint gun, you need to light it on the side of the Bunsen burner so that the flame reaches around the flame and away from you.3. Once the flame is lit, you can adjust the height of the flame to what you will need for your experiment. If you are heating something, you will need to adjust the height of the holding tray to the flame. Do not try to adjust the flame to the height of the holding tray. Flames can and will get out of control if you are not meticulous. It could also wrap around the glass container of the substance and burn it to the glass. Every step counts.4. After the experiment is done and all the data is completed, you will need to turn off the Bunsen burner. To do this, make certain whatever you are heating is off the holding tray is removed. These chemicals can get very dangerous when heated, so be cautious. Remember to use tongs to remove the glass container and put it far enough away from the burner to be safe.5. Once the glass container is removed, turn off the gas at the Bunsen burner's base and at the wall. Once the gas is off, the flame should automatically be extinguished. If it is not, you may have a gas leak. Make certain the gas is completely off on both sides. If it is off and the flame has not gone out, alert your professor immediately.jejeje...-sLuRp3e-. ^_^V