Black represents Hot and White common. For the light to operate it needs a white and black wires. The switch box has two cables with a white and black wire plus a ground. One wire is from the supply and the other to the light. Connecting the whites just provides common directly to the light. The blacks go into and out of switch because it is the hot side that is being switched.
with a standard 1 pole light switch (one switch operating the light) it is black wire to black wire and white to white (non grounded)
You would wire the switch to the first light. Code says to break the black or power side of the circuit. Connect the white to the light. Take the black down to the switch on the black wire and back to the light on the white. This is a line of wire from the light to the switch. From the first light, take the white and the return white from the switch to the second with another run of wire. This will be regular black white with ground. White to white and at the first light the return line from the switch is white but hook to the black to the second light. Second light to third just continues the two wires. Black to black, white to white. I think this is clear enough to follow. If not, ask again.
You put switch in series with the black supply wire and the black wire to the first light. Then connect black wire of first light to black wire of second light, black wire of second light to third light and so forth. Do the same with the white wires and ground wires.
You have a 3 way switch. Your black wire is the hot wire. Your green wire is the ground wire. Your red and white wires go to the light and other switch. You should have gotten a wiring diagram with your switch.
Remove the light sensor and place a switch between the red and black wires. The black wire is one leg of the "hot" pair and the load is connected to the red wire. This will now switch the black hot through the red wire that goes to the load.
with a standard 1 pole light switch (one switch operating the light) it is black wire to black wire and white to white (non grounded)
black plastic switch you pull
If you are down stream from the switch then all blacks together, all whites together and all grounds (bare wires) together.
You would wire the switch to the first light. Code says to break the black or power side of the circuit. Connect the white to the light. Take the black down to the switch on the black wire and back to the light on the white. This is a line of wire from the light to the switch. From the first light, take the white and the return white from the switch to the second with another run of wire. This will be regular black white with ground. White to white and at the first light the return line from the switch is white but hook to the black to the second light. Second light to third just continues the two wires. Black to black, white to white. I think this is clear enough to follow. If not, ask again.
You put switch in series with the black supply wire and the black wire to the first light. Then connect black wire of first light to black wire of second light, black wire of second light to third light and so forth. Do the same with the white wires and ground wires.
switch lights off
Sure. For a light you need a fixture to hold the light and the light itself. The light needs to be connected to a voltage supply which you can get from the outlet. In the outlet box you will have a black, white and bare ground wire. Essentially you connect the white and bare wires directly to the light and switch the black wire (hot) through a switch.
homer plessly
In the room near the theater
You have a 3 way switch. Your black wire is the hot wire. Your green wire is the ground wire. Your red and white wires go to the light and other switch. You should have gotten a wiring diagram with your switch.
Remove the light sensor and place a switch between the red and black wires. The black wire is one leg of the "hot" pair and the load is connected to the red wire. This will now switch the black hot through the red wire that goes to the load.
It sounds like the feed for the kitchen is fed through the bathroom switch box. The black feeding the kitchen light is connected to the wrong side of the switch. There should be two black on one side of the switch and one on the other. One of the two blacks need to be moved to the other side of the switch. **BE VERY CAREFUL or CALL A LICENSED ELECTRICIAN** Even with the switch OFF the live side of the switch will be LIVE!!