0
Why would the water pressure drop from one sink to the other when the water lines are teed of the same line?
Wiki User
∙ 12y ago
The water pressure drop could be due to a clogged aerator at faucet out, a kinked supply line or partially closed shut of that services that fixture.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How can you get better hot water pressure with galvanized pipes Is there any other way except putting new water pipes like a plumber told me?
You actually SHOULD replace the galvanized lines as they completely rust up on the inside. The only other thing that you could do is purge the lines with high pressure air or water. Careful though! You would be taking a risk that a fitting would blow!
Why would just the upstairs faucets sputter when first turned on?
Air in the water lines to the upstairs. Not enough water pressure.
What is the fix for when you flush the toilet while in the shower the water gets hot?
New pressure balance faucet or you can install a pressure balance valve in the water lines behind tub or if you have a crawl space you can install it on the water lines there. But install only too the lines to tub faucet. And they are not easy no matter where you install. I would just tell everyone not to use any water till you are done with shower.
Why would the hot water in the bathtub have no pressure but the cold water is fine There was a leak under the hot water handle We had the sellers get a plumber to fix it now no hot H20 pressure?
You can try following the water lines back to the water heater to make sure there is not a valve closed holding the water back that may have been forgotten after the repair. This being the case, I would be worried that the repair was not check to see if it was done correctly.If you have pressure on the hot water at other faucets in the home, then I would think this could be the problem. Need more help contact me through my board and I will try to help.
What would cause a loss of hot water and pressure in one bathroom when you have water running in both bathrooms?
THE THING THAT CAUSES YOU TO LOSE PRESSURE AND HOT WATER IS BOTH BATHROOMS ARE CONNECTED TO THE SAME LINES. SO WHEN YOU RUN SOMETHING, THEN RUN SOMETHING ON THE OTHER SIDE, YOU LOOSE POWER THAT YOU WOULD NORMALY HAVE IF ONLY ONE BATHROOM IS ON. THERE IS NO QUICK FIX, TO FIX YOU MUST REPLACE ONE OF THOSE LINES WITH NEW ONES PROBABLY FROM THE BASEMENT. ITS ALOT OF WORK, AND COSTLY. JOE HOJAS
Why would a 2 story house with 2 water heaters have hot and cold water in the downstairs bath but only hot in the kitchen and no water upstairs?
it sounds like there are crossed lines. if there is no water upstairs there has to be a valve that is off. even if there is low pressure it would eventually fill the line and you would get some water.
What would cause temperature and pressure fluctuation in the shower when no other water source is on?
My first thought is a leaky hot water line.
How would you explain voltage to secondary students?
Voltage is the pressure that pushes electricity through wires (or other conductors) in the same way that water pressure pushes water through pipes.
What would cause a tub faucet to lose water pressure when the other faucets work?
check for leaks
What type of water pressure booster system would help increase the water pressure from a city water system?
Davey Pressure Booster Systems with Torrium® control technology would help increase the water pressure from a city water system.
Would having air in one's pipes cause a reduction in hot water pressure when taking a shower?
== Answer== I don't think so, but get the air out of lines to make sure.
Can you have too much water pressure in a residential house requiring a pressure release valve?
The water pressure in my house is about 140PSI. Which is definitely dangerous. It happens more often than you would think. What happens is a city will use water supply lines which are too small for the water requirements. Therefore, they have to increase the pressure. You wouldn't want a pressure relief valve, because then if the pressure was too high, it would just spray water everywhere to release the pressure. You would want a pressure regulator installed, which is what I am working on for my house right now. Just to let you know though, you may have to get a thermal expansion tank for your water heater if you don't have one. See, the new pressure regulators have a check valve in them, which prevents water from traveling back into the city pipes once it has gotten into your house. When your water heater heats the water, the air bubbles in it expand, which increases the water pressure, and will probably cause your pressure relief valve on your water heater to blow. You can get a cheap water pressure meter at any improvement store to check it out. 50-60 PSI is ok. I would say you could take it up to 70 or 80 PSI safely.
