0
Your brake lights don't work on Renault megane scenic fuse fine bulb fine brake light switch fine?
Its a common manufacturing fault. if you remove the rear light complete. then remove the actual bulb holder. If you then take out the bulb that seems not to be working, you will find that, there usually is some corrosion on the plate that contacts with the bulb. which stops current from reaching the siad bulb.
What else can I help you with?
How do you switch off airbag and service light in 54 Renault megane?
i have a megane scenic 2004 and just discovered that i can switch off passenger airbag by a switch in the dash , which you would see when opening the drivers door. Sorry don not know about service light.
Why won't Renault megane brake lights work It's not the 3no. bulbs and it's not the fuses?
The probable cause of the brake lights not working on your Renault is the brake light switch. The brake light switch can be found under the dashboard by the foot pedal.
Can you override your immobilizer on a Renault scenic?
yes, you have two run a wire from the ignition where the lights are and connect it two the battery, this will power it with out the emobiliser acting as the switch...
Location of reverse light fuse Renault megane scenic 2004?
The reverse light fuse can be found in the fuse box. The reverse light fuse relay switch can be found beneath the drivers side dashboard.
Where is the mode button on a Renault megane scenic 54 plate?
In a Renault Megane Scenic 54 plate, the mode button is typically located on the center console or dashboard, often near the audio system controls. It may also be found on the steering wheel, depending on the specific features of the model. Look for a button labeled "MODE" that allows you to switch between different audio sources or settings. If you're having trouble locating it, consult the vehicle's user manual for precise details.
How do you disable the passenger airbag on a 2001 Renault Megan scenic?
To disable the passenger airbag on a 2001 Renault Megane Scenic, locate the airbag switch, which is typically found on the side of the dashboard or near the driver’s seat. Use the vehicle's key to turn the switch to the "off" position. Ensure that the airbag warning light on the dashboard illuminates to confirm that the airbag has been successfully disabled. Always consult the owner's manual for specific instructions and safety precautions.
Fan wont stop after engine turned off in Renault scenic 2000?
If the fan does not stop running after the engine is shut off in the Renault Scenic 2000, there could be a problem with the fan relay switch. The fan relay switch is located in the fuse box.
How do you change the reverse light switch on a megane?
To change the reverse light switch on a Renault Megane, first, locate the switch, which is usually positioned on the transmission. Disconnect the battery to ensure safety, then remove the electrical connector from the switch. Unscrew the old switch using the appropriate tool and replace it with the new one, ensuring it's securely tightened. Finally, reconnect the electrical connector and the battery, then test the reverse lights to ensure they function correctly.
Where to find fog light switch on Renault scenic 02?
it is on the headlight satellite ( stalk) just twist it
How do you get the flashing spanner off the dash board in a Renault megane?
switch engine off wait 15 seconds then switch ignition back on. it works on my car.
Why won't Fan won't stop after enigine turned off Renault scenic 2000?
A faulty fan relay switch is likely the problem if the fan continues to run after the engine is shut off. Production for the Renault Scenic began in 1996.
How do you remove the hazard warning switch 2001 Renault megane?
To remove the hazard warning switch on a 2001 Renault Megane, first ensure that the ignition is off and disconnect the car battery for safety. Carefully pry off the switch cover using a flat tool to avoid damage, then gently pull the switch out of its socket. Disconnect the wiring harness attached to the switch by pressing the release tab and pulling it free. Finally, replace with a new switch by reversing the process.
