0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How is the voltage measureing range of the basic analog meter movement extended?
shunt resistances are used to increase the range of ammetes and moreover it is praticularly then we have to low value shunt resistance.
Functions of the Parts of an analog multimeter?
Parts of Analog MultitesterScale Pointer position adjuster Range selector knob Meter cover Panel 0?? adjuster knob ?input terminal ?input terminal pin Plug Test lead?Red? Test lead?Black Test lead(TL-21) Arnel Gamao Jr. Parts of Analog MultitesterScale Pointer position adjuster Range selector knob Meter cover Panel 0?? adjuster knob ?input terminal ?input terminal pin Plug Test lead?Red? Test lead?Black Test lead(TL-21) Arnel Gamao Jr.
Why will a light not work on knob and tube wiring with 120V of power on meter?
According to www.wilberelectrical.com knob and tube wiring is no longer legal. You will need to replace it. Chances are, as knob and tube wiring is very, very old, something has broken or it has been disconnected as knob and tube is not very safe. I would recomment replacing it with modern wiring devices rather than trying to repair it.
What is the formula for calculating wattage?
wattmeter is constructed such that it read only power on a single scale. Only single scale will avilable to read the measured power. In order to take the acuurate reading just we measure the reading and we will multiple along with factor called multificaion factor. That's depends on on which voltage knob we connected and also the current. Multification factor can be dtermind by: Multification factor =(voltage range*current range*pf)/Max scale deflection...
Why is your shower luke warm when the bathroom sink runs hot?
I ran into this problem at my new house. You have to take the shower knob off and there will be instructions inside to adjust the water temperature. This is to protect children from getting burnt from turning the water on too hot.
How is the voltage measureing range of the basic analog meter movement extended?
shunt resistances are used to increase the range of ammetes and moreover it is praticularly then we have to low value shunt resistance.
When a multimeter is set to measure resistance what reading would you expect when the probes are touching?
Hold the probes at the end of the test leads together. The meter pointer should move fully to the right. Locate the "Zero Adjust" knob and rotate so that the the meter indicates "0" (or as close to "0" as possible). Note that this position is the "short circuit" or "zero ohms" indication for this R x 1 range of this meter. Always remember to "zero" the meter immediately after changing resistance ranges.
How do you adjust dashboard lights on an Audi a4?
You turn the clock adjustment knob without pulling it. TO adjust the time you pull the knob and turn, to adjust dash lights you just turn knob.
What is the function of the fine adjust in microscope?
After you adjust the coarse adjustment knob, the fine adjustment knob makes it sharper or clearer.
What is accomplish by turning adjusment knob upward?
The answer depends on what the knob is meant to adjust!
Function of Zero Ohm Adjust Control?
The Zero Ohms Adjusting Knob on the Multi Tester ToolThe VOM (Volt-Ohm Meter) is type of measuring equipment used for reading the three major properties of electricity which are the Voltage, Current and Resistance. This tool typically has a huge rotating knob on the middle part which allows you to select the type of electrical property that you would like to measure. At the bottom part are the two probes differentiated with Red and Black color. The Red probe denotes the positive terminal while Black for the negative terminal.Now, you might be wondering about the other smaller rotating knob just above the huge selector which is labeled as Zero Ohm. This adjusting knob only concerns about resistance. It doesn't have any effect when the primary selector is set for Voltage and Current.
What is the function of fine adjustment knob in microscope?
After you adjust the coarse adjustment knob, the fine adjustment knob makes it sharper or clearer.
How do you adjust the passenger side mirror on a 1993 buick skylark?
On the driver side mirror adjust turn the adjust knob clockwise and that will allow you to adjust the driver side mirror. Turn the adjust knob back counterclockwise for the driver side mirroradjust
How do you adjust the passenger side mirror of a Chevy Trailblazer?
The knob that adjusts the driver side mirror also adjusts the passenger side mirror. Simply turn the knob to the right to adjust the passenger side, and turn to the left to adjust the driver side. Leaving the knob in the middle, neutral position will keep the mirrors from changing if the knob is hit.
How do you configure a midland cb radio model 75-784?
Twist the power knob, adjust the squelch knob and your on.
How do you set the clock on Ford Windstar 2003?
Hold the volume knob in. The clock will flash. Adjust the clock with the tuning knob while holding the volume knob in.
How do you adjust a puritan watch day hand?
To adjust the day hand on a puritan watch, gently pull out the crown to the first position and rotate it clockwise until the desired day is displayed. Make sure to push the crown back in after setting the day hand to ensure it stays in place.
