0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Does exception always signal an error?
It depends on exactly how you define an error. If an exception is thrown, then it means something has gone wrong. Some Exceptions, such as a NullPointerException, will almost certainly signal an error in your code or data. Others, such as IOExceptions, can be caused by things outside your control, and would probably not be considered errors.
Why it is generly true that a digital signal required high bandwidth than analog signal?
A: Analogue signal Direct voltage that varies in the low spectrum of frequency on digital signal the information is deciphered in micro seconds therefore the frequency must be hi the higher the better.
What is definition of open loop transfer function?
According to 'Modern Control Engineering' written by Katsuhiko Ogata, the ratio fo the feedback signal, H(s)C(s)to the actuating error signal (R(s)-B(s)) is called the open-loop transfer function. Here, H(s) is the transfer function of the feedback signal detector, C(s) is the output signal and R(s) is the setpoint signal.
What is signal unknown signal received error message in FPGA xilinx software?
Any signal would have four states high indicated by 1, low indicated by 0, high impedance indicated by Z and unknown indicated by X. An unknown signal often occurs when you have not connected the pin to anything or you are trying to take output from the pin while it is not really giving the proper output
How do you put signal in a sentence?
i have no signal on my phone i have signal on my phone i have no signal on my television i have signal on m y television the signal has been interupted i dont know the hand signal i need to know the signal what is the signal strength teach me the hand signals what is the signal for danger i have little signal i have high signal i have no signal how much signal do i have how do i tell how much signal i have is there a sign for signal by the way you already put it in a sentence by asking a question lol
What is error 9 on rdc634 clarion CD player?
Error 9 on that particular changer is a weak RF signal error. That means that the unit is not sending out a strong enough signal to the antenna. Error 9 on that particular changer is a weak RF signal error. That means that the unit is not sending out a strong enough signal to the antenna.
What is the use of connecting an integrator in delta modulation?
integrator converts the quantised signal to saw tooth signal which then compared with the present signal and error signal is generated,and error signal is quantised and the process continues
What is the most common teenage driving error?
Turning without signal
What are fault codes P202C-004 on Mercedes?
P202C-004 = CAN BUS signal from EIS controller,CAN BUS signal error
What is p0344 error code on dodge Dakota?
Camshaft postion sensor signal intermittent.Camshaft postion sensor signal intermittent.
State one example of an automatic Voltage system that is error actuated?
An AVR circuit, the voltage sensing unit measures the incoming voltage and compares it to the set point. Then an error signal is produced and sent to the amplifier,the error signal then reaches a firing circuit which consists of a thyristor with a field current which will adjust alternators output current. Dependant on the signal from the actuating unit.
Does exception always signal an error?
It depends on exactly how you define an error. If an exception is thrown, then it means something has gone wrong. Some Exceptions, such as a NullPointerException, will almost certainly signal an error in your code or data. Others, such as IOExceptions, can be caused by things outside your control, and would probably not be considered errors.
What is slope overload error in delta modulation derive an expression for it?
: If the input signal amplitude changes fast, the step by-step accumulation process may not catch up with the rate of change of the signal this is called slope overload error
What is the importance of linear prediction in signal processing?
Linear prediction in signal processing is important because it allows for the estimation of future values of a signal based on its past values. This is especially useful in applications such as speech and audio coding, where the accurate prediction of future samples can lead to efficient compression algorithms. Linear prediction also finds applications in noise reduction and speech enhancement techniques.
My PSP says A DNAS error has occured80530186 What do I do?
This error means that you are locked into an internet provider. This happens sometimes when using public Wi-Fi and your PSP will give you the error code because the signal is encrypted.
What does error code p0335 on a 1999 Chevy cavalier mean?
Problem with the signal from the Crank Sensor.
Reason use an op amp in a closed loop control system?
Differential Amplifier or Summing Amplifier are usually used in a closed loop control system. The error signal will be the DIFFERENCE between the setpoint value and feedback value for Differential Amplifier. Whereas for Summing Amplifier, the error signal will be the difference between the setpoint value and feedback value only if one of the value is inverted in polarity. Another reason Op Amp is used: amplify the error signal as error signals are usually very small. Hope this helps.
