answersLogoWhite

0

It is in the steering column, right behind the lock cylinder. (where you put the key in to start) You have to take the molding off of the lower column. Loosen four bolts to drop the clomn down. Romove lock cylinder. Undo wiring harness to ignition switch. Remove the two screws mounting swith and replace. The switch should come pre set to on position. Wich the lock cylinder has to be lined up to in order to remove it. Note: the two screws that hold the ignition switch may look like rivets, but they are threaded. Take a pair of needle nose vice grips to remove them. The new switch should come with a pair of hex countersunk screws. This will make it esier to replace again if ncessary. Good luck.

User Avatar

Wiki User

17y ago

What else can I help you with?

Continue Learning about Art & Architecture

How do you replace a starter switch in a 1987 Chrysler LeBaron Town and Country Turbo with a tilt wheel?

There is a solonoid on the starter and the ignition switch is on the steering column.


How do you replace the ignition switch in a 1987 grand marquis with broken tumbles?

found this, might be the same, Merry Christmas, anyways! :) For a 1988 Mercury Marquis remove bottom shroud from steering column (5 Philips head screws). There is a wire running from the ignition switch to the left side of the steering column; detach it from the coupler (This can be done without a tool). Turn key to ON position until the panel lights come on. There is a small pin near the bottom of the key lock; push it in and pull the ignition switch out (don't panic if the wire seems to be stuck; it will come out). To replace, turn new ignition switch to same position. Push pin on the ignition switch in while sliding it back into the steering column. Reconnect wire and then replace shroud.


1987 Scottsdale how to bypass ignition switch with pushbutton Which wires do I need to tie in to?

orange and pink


What are symptoms of neutral safety on a 1987 Mercedes Benz 420 SEL?

The symptoms of neutral safety, on your 1987 Mercedes-Benz, will begin with the vehicle not shifting properly. Another symptom is the vehicle ignition switch not turning to the off position.


Where is the ignition module on a 1987 Chrysler fifth avenue?

There is no ignition module on a 1987 5th ave. The spark control computer is on the air cleaner with a vacuum line hooked to it.

Related Questions

How do you remove ignition switch on 1987 Mercedes 420sel?

To remove the ignition switch on a 1987 Mercedes 420SEL, first disconnect the battery to ensure safety. Then, remove the steering wheel and the steering column cover to access the ignition switch. Locate the ignition switch, detach any wiring harnesses, and remove the mounting screws or clips securing it in place. Finally, pull out the ignition switch and replace it as needed.


How do you change the ignition switch in a 1987 Ford Bronco 2?

Remove the airbag and steering wheel, remove the torx screws from the steering housing and remove the housing, remove the screws from the signal and wiper switch, and remove the screws above the ignition switch and remove the switch. Replace the switch and replace everything in reverse.Ê


How do you replace a starter switch in a 1987 Chrysler LeBaron Town and Country Turbo with a tilt wheel?

There is a solonoid on the starter and the ignition switch is on the steering column.


Where is the safety switch located in 1987 Thunderbird?

It will be under the clutch, as it meets the firewall.


Why is your 1987 lebaron dinging inside constantly like headlights are left on?

Your key switch contact inside the ignition switch cylinder may be stuck closed. You may need to replace the switch or the ignition key cylinder. On a Ford and GM, the contact is replaceable without the ignition switch, but requires the steering wheel removed to replace it. Not sure what is required for the Lebaron, but it is not a major task to do for a mechanic.


How do you replace 1987 silverado ignition switch?

the truck will not crank or anything with the key it wont even starter when you ark the starter all it does is whizz


How do you replace an ignition switch on a 1987 Mercury Cougar?

The ignition switch is located on the bottom of the steering column. Take out the 4-6 screws that hold the bottom piece and you will see the switch should be about 3-4 inches long held in place by 2 screws. take black plug off then replace switch plug back in and there you go.


Where is the brake light fuse on a 87 Thunderbird?

The brake light fuse on a 1987 Thunderbird is located on the back of the headlight switch. It is not in the fuse box.


How do you change ignition switch on 1987 ford f150?

The ignition switch is usually mounted to the steering column and is operated by a linkage rod. NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch: * Remove the ignition switch wiring harness. * Unbolt it from its position. * Bolt the new switch into position. * Attach the witing harness.


Where is the brake light switch located on a 1987 ford thunderbird?

Under the brake pedal. Looking up at the pedal you will see the switch it is srewed to the dash and rests on the metal arm of the pedal when you press the brake pedal the switch close's and the brake lights come on. To replace the switch it is very straight forward just remove the srew from the dash separate the wire and replace..


Do you have to remove the fuel tank to replace the fuel pump on a 1987 ford thunderbird?

Sorry Yes You Do.


Why won't my 1987 Corvette start after i have ran it but then when i let it cool down it would start?

A friend had the same problem with his 87 Corvette . His was the chip in the ignition key . Had to replace ignition switch and key , about 40 dollars for the parts .