answersLogoWhite

0


Best Answer

Under dash on steering column. I believe it is white with a rod going to it.Two screws holding it on.

User Avatar

Wiki User

โˆ™ 2006-04-12 06:08:10
This answer is:
User Avatar
Study guides

Add your answer:

Earn +20 pts
Q: How do you replace the ignition switch on a 94 GMC Jimmy?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Art & Architecture

How do you repair an ignition switch on a 1997 GMC Jimmy 4X4?

you cannot repair the switch,you must replace and relearn.gmjim


How do you replace the ignition switch in a 1988 GMC Vandura with tilt wheel?

The switch is located on the left side of the steering column. You have to remove the panel underneath the dash to access it. There will be two screws holding it on.


How do you replace an ignition switch on a 1993 gmc sierra?

its a long process,you need a steering wheel puller, once its off take the hazard button assembly out, take the turn signal loose, pull old ignition out, carefully install new one, and reverse procedure


How do you change a ignition switch in a 1992 GMC Jimmy?

First you need to take off your horn cap. Then take a 13/16 socket to loosen the steering wheel. Take a steering wheel puller to get the wheel off. After that you need to get a lock plate compressor to push the plate down to remove the snap ring. (There is a tool for this but it can be taken off by a flat head screwdriver. Now you need to undo the screws in the turn signal switch and unscrew the hazard light button on the outside of the column. After you take out the turn signal switch there will be a screw right under the slot for the ignition switch on the inside. You need to unscrew this. Now you have to have your key in the ignition to remove the ignition switch. Turn your ignition switch either all the way forward or back to remove the ignition switch


What do you do if you changed the ignition switch in a GMC Jimmy and now it will not start?

Depends on the year, if it is a newer truck than the theft system will have to be relearned. turn the key on and let it sit for 10 minutes. on some vehicles this works, otherwise you need to have it done at a gm dealer.

Related questions

How do you change the ignition switch on a 1996 GMC Yukon?

howdo you change an ignition switch on a 1996 gmc jimmy howdo you change an ignition switch on a 1996 gmc jimmy


How do you repair an ignition switch on a 1997 GMC Jimmy 4X4?

you cannot repair the switch,you must replace and relearn.gmjim


How do you replace ignition switch on 97 gmc jimmy?

Pull your steering colum apart along with steering wheel and dash plastic, ignition swith is next to the key tumbler. Swap the parts.


How do you change the ignition switch on a 2004 gmc 1500 sierra truck?

how to remove cover to replace ignition lock cylinder and what type of tools do i need


How to replace a heater core in a 1992 GMC Jimmy?

I need to know how to replace a heater core in a 1992 GMC Jimmy?


Your 1998 gmc jimmy starts and then off acts like it is not getting enough fuel you have replaced fuel pump and filter what could be causing this?

You may have a faulty ignition switch. The ignition switch feeds the fuel pump.


Relay switch on a 1996 gmc jimmy?

There are several relay switch is on your 1996 GMC Jimmy. The brake light relay switch can be found below the dashboard in the engine compartment.


Where is the ignition relay on a 1992 GMC G2500 conversion van?

That 92 GMC van doesn't have a relay for ignition. Power for the ignition is supplied from the ignition switch.


How do you replace an abs pump on a 1999 GMC Jimmy?

How do you change the abs pump on a 2001 gmc jimmy


Location of fuel cutoff switch 2000 gmc jimmy?

Some vehicles are not equipped with a fuel cutoff switch. A 2000 GMC Jimmy is an example of a vehicle that does have a fuel cutoff switch.


How do you install ignition switch 1988 gmc truck?

You need to remove the steering wheel first with a puller. There is a latch you can trip with a small screwdriver that will let the ignition switch slide out. Simply replace the switch and put the steering wheel back on.


How do you replace ignition switch on 1986 GMC sierra pickup?

pulled steering wheel still cant get plastic cover off to acess switch any help

People also asked