What instrument measures seismic activity?

Answer 1

Geophone is the instrument used for measuring earth tremors!!!

By the way, the term geophone derives from the Greek word "geo" meaning "earth" and "phone" meaning "sound".

A geophone is a device which converts ground movement (displacement) into voltage, which may be recorded at a recording station. The deviation of this measured voltage from the base line is called the seismic response and is analyzed for structure of the earth.

Geophones have historically been passive analog devices and typically comprise a spring-mounted magnetic mass moving within a wire coil to generate an electrical signal. Recent designs have been based on Microelectromechanical systems technology which generates an electrical response to ground motion through an active feedback circuit to maintain the position of a small piece of silicon.

The response of a coil/magnet geophone is proportional to ground velocity, while microelectromechanical systems devices usually respond proportional to acceleration. Microelectromechanical systems have a much higher noise level (50 dB velocity higher) than geophones and can only be used in strong motion or active seismic applications.

The frequency response of a geophone is that of a harmonic oscillator, fully determined by corner frequency (typically around 10 Hz) and damping (typically 0.707). Since the corner frequency is proportional to the inverse root of the moving mass, geophones with low corner frequencies (< 1 Hz) become impractical. It is possible to lower the corner frequency electronically, at the price of higher noise and cost.

Although waves passing through the earth have a three-dimensional nature, geophones are normally constrained to respond to single dimension - usually the vertical. However, some applications require the full wave to be used and three-component or 3-C geophones are used. In analog devices, three moving coil elements are mounted in an orthogonal arrangement within a single case.

The majority of geophones are used in reflection seismology to record the energy waves reflected by the subsurface geology. In this case the primary interest is in the vertical motion of the Earth's surface. However, not all the waves are upwards travelling. A strong, horizontally transmitted wave known as ground-roll also generates vertical motion that can obliterate the weaker vertical signals. By using large areal arrays tuned to the wavelength of the ground-roll the dominant noise signals can be attenuated and the weaker data signals reinforced.

Analog geophones are very sensitive devices which can respond to very distant tremors. These small signals can be drowned by larger signals from local sources. It is possible though to recover the small signals caused by large but distant events by correlating signals from several geophones deployed in an array. Signals which are registered only at one or few geophones can be attributed to ll, local events and thus discarded. It can be assumed that small signals that register uniformly at all geophones in an array can be attributed to a distant and therefore significant event.

The sensitivity of passive geophones is typically 30 Volts/(meter/second), so they are in general not a replacement for broadband seismometers.

Conversely, some applications of geophones are interested only in very local events. A notable example is in the application of Remote Ground Sensors (RGS) incorporated in Unattended Ground Sensor (UGS) Systems. In such an application there is an area of interest which when penetrated a system operator is to be informed, perhaps by an alert which could be accompanied by supporting photographic data.

seismograph

Answer 2

seismograph
There are two instruments, which are basically the same thing. There is the seismograph , and a more specific tool measures the waves on what is called the Richter scale. Earthquakes are given a number from one to ten, ten being the strongest. The strongest earthquake that their ever was, was measured a 9.3.

Answer 3

I believe the same instruments that detect earthquakes are also used in detecting volcanic activity. Seismographs detect changes in earth movements.

Answer 4

A machine used to measure earthquake activity is a seismometer.

Answer 5

Seismographs are often used to study the activity of volcanoes. Like earthquakes, volcanoes are the result of the movement of tectonic plates, which can be measured using this device.

Answer 6

Seismologists are still trying to link seismographic data to volcanic activity. It is not yet as accurate as may be desired.

Answer 7

seismometer measures activity, a seismograph records it (like on paper or a hard drive).

Answer 8

siesmograph