0
CAMSHAFT POSITION SENSOR
The camshaft position sensor is located in the distributor on all 3.9L V-6 and 5.2/5.9L V-8 engines Camshaft Position Sensor
REMOVAL
Distributor removal is not necessary to remove camshaft position sensor
Remove air cleaner assembly.
Disconnect negative cable from battery.
Remove distributor cap from distributor (two screws)
Disconnect camshaft position sensor wiring harness from main engine wiring harness.
Remove distributor rotor from distributor shaft.
Lift the camshaft position sensor assembly from the distributor housing Camshaft Position Sensor
INSTALLATION
Install camshaft position sensor to distributor. Align sensor into notch on distributor housing.
Connect wiring harness.
Install rotor.
Install distributor cap. Tighten mounting screws.
Install air cleaner assembly.
Wiki User
∙ 15y ago
Wiki User
∙ 14y agoDepends on the engine, old strait 6 in the center of the block passenger side in some inside the distributor since it has a cap and rotor, later versions of the strait 6 with no distributor but coils on plug is just a sensor located where the distributor would be center right side of the engine block, on the 5.2 V-8 in the rear center of the engine inside the distributor, on the later V-6 and 4.7 V-8 on the front right side of the engine cylinder head
Wiki User
∙ 13y agoIts on the right hand side of the engine at the front just below the rocker cover and it has 3 wire plug going to it it is visible from the top but easier to get out thru the bottom
This sensor is EASILY reached from the top..........Above the oil filter in plain view.
Wiki User
∙ 14y agoits on the driverside on the back of engin on top of bell housing the pulug is passengerside by the coil plug area to get out you need lots of extensions and go in by rear of tranny good luck they suck
Wiki User
∙ 15y agoIt is on the back side of the engine located behind the alternator and above the oil filter. V6 it is in the distributor 4 cyl it is on the end of the head
Wiki User
∙ 14y agoThe sensor is located on the front, passenger side of the motor just under the alternator and is mounted with a 10mm bolt. Remove the air filter assembly for easy access.
Wiki User
∙ 14y agoThe cam sensor is located under the front of the right front (pass) head.
Wiki User
∙ 13y agoit is located at the right handside of the engine below the coil pack assembly gray it color
Wiki User
∙ 7y agoIt's where the distributor used to be.
Add your answer:
Earn +20 pts
Where is the camshaft position sensor on 2002 Dodge Neon?
The crankshaft sensor on a 2 door Honda Accord with a 3L V6 engine is located on the side of the engine, near the oil filter. It screws into the side of the block and outputs the loading of the crankshaft to the vehicle's computer.
How do you troubleshoot a fault code 54 on a 1997 dodge stratus?
Code 54-No cam signal at the PCM-No camshaft position sensor signal detected during engine cranking.
What do mil codes p0016 and p0034 mean on 2003 dodge ram 4.7?
Trouble code P0016 means: Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor A Trouble code P0034 means: Turbo/Super Charger Bypass Valve Control Circuit Low
1996 Dodge Avenger torgue for Camshaft Bearings?
2.0 litre DOHC 4 cyl- caps 1 and 6 is 20 ft-lb caps 2-6 is 108 inch-lb
Find throttle position sensor for 2002 dodge ram cummins 2500?
It is called a APPS accelerator pedal position sensor. It is located on the front of the engine. It is the part that the throttle cables hook to.
Where is the camshaft position sensor on 1999 dodge avenger 2.5?
It is inside the distributor. It is only serviced with the entire disributor.
2006 dodge durango camshaft position sensor location?
The 2006 Dodge Durango camshaft position sensor is located on the back end of the head. The position sensor should be labeled as such.
Where is the camshaft position sensor located on a 2006 dodge stratus?
Where is a camshaft position senser located on a 2006 dodge durango/
Where is the camshaft position sensor in a 95 dodge 2500 3.9?
The camshaft position sensor on a 95 Dodge 2500 3.9 is located inside the distributor, under the rotor.
Where is the camshaft position sensor on a 2001 5.2 Dodge Ram sport?
The camshaft position sensor on a 2001 Dodge Ram 5.2 is inside the distributor, under the rotor.
What does code P0340 mean on a 1999 Dodge Durango?
Camshaft position sensor circuit malfunction.Camshaft position sensor circuit malfunction.
What does code P0344 mean on a dodge 97 caravan 2.4?
P0344 Camshaft Position Sensor Circuit IntermittentP0344 Camshaft Position Sensor Circuit Intermittent
Where is the camshaft sensor located on a 2006 dodge stratus?
Where is a camshaft position senser located on a 2006 Dodge durango/
Where is the camshaft position sensor on a dodge ram 2500 5.7?
The camshaft position sensor on a Dodge Ram 2500 5.7 engine is located at the rear of the camshaft near the top of the motor. It monitors the motion of the camshaft and constantly updates the vehicle's computer.
What is cmp or ckp on an 2000 Dodge Intrepid?
CMP : camshaft position sensorCKP : crankshaft postion sensor.CMP : camshaft position sensorCKP : crankshaft postion sensor.
Where is the camshaft position sensor on a 1998 Dodge truck?
It is inside the distributor.
Where is the Camshaft position sensor located on a 1988 dodge Dakota?
It is in the distributor.
