0
What else can I help you with?
What is the cable size needed to run 400V 50H 185KW delta motor?
To determine the cable size for a 400V, 50Hz, 185kW delta motor, you first calculate the full-load current using the formula: I = P / (√3 × V × PF), where PF is the power factor (typically around 0.8 to 0.9 for motors). Assuming a power factor of 0.85, the current is approximately 245A. You would then refer to local electrical codes and standards, such as the NEC or IEC, to select an appropriate cable size that can handle this current while considering factors like ambient temperature and installation conditions. Generally, a cable size of around 50mm² copper or 70mm² aluminum may be required, but always check the specific regulations and derating factors for your installation.
What is cable glanding?
A device designed to permit the entry of a cable into an electrical equipment and which provides sealing and retension. Cable well tightened with supporting of cable holding material into an electrical equipment or panels.
What is the type and size of cable gland or 2 core cable?
To answer this question the size of the cable or the amperage of the load is needed to calculate the correct wire size and connectors to fit the cable.
What size of coper cable for a 3P 380V 15kw Air conditioner and the distance of cable is about 40meters?
The cable size is : 4*25 mm2
What is the difference between armored cable and flexible metallic conduit?
Armored electrical cable contains insulated electrical service wires protected by a flexible steel covering. Metallic Conduit is a tube or pipe though which we lay electrical cable.(Most commonly lighting cables).
What is the cable size needed to run 400V 50H 185KW delta motor?
To determine the cable size for a 400V, 50Hz, 185kW delta motor, you first calculate the full-load current using the formula: I = P / (√3 × V × PF), where PF is the power factor (typically around 0.8 to 0.9 for motors). Assuming a power factor of 0.85, the current is approximately 245A. You would then refer to local electrical codes and standards, such as the NEC or IEC, to select an appropriate cable size that can handle this current while considering factors like ambient temperature and installation conditions. Generally, a cable size of around 50mm² copper or 70mm² aluminum may be required, but always check the specific regulations and derating factors for your installation.
What is the recommended cable size for a 100 amp electrical circuit?
The recommended cable size for a 100 amp electrical circuit is typically 3 AWG copper or 1/0 AWG aluminum.
Where can find Electrical table for size of cable?
Electricians will use their electrical code book to fine these values.See related links below
When is wire size an electrical hazards?
Wire size becomes an electrical hazard when it is under rated for the amount of current (Amps or I) it has to carry.Current is the flow of electrons in a circuit. If the current is too large for the cable, the cable will be subject to heating, which is a possible fire hazard.
Size 134 kva cable?
A 134 kVA cable typically refers to the size of cable required for a 134 kilovolt-ampere electrical load. The size of the cable needed will depend on factors such as the length of the cable run, the voltage drop allowed, and the type of insulation and conductor material required to safely carry the current. It is recommended to consult with a qualified electrical engineer or contractor to determine the specific cable size needed for your application.
What should be the distance between controle cabledatatransmition cable and electrical cable?
what should be the distance between instrument cable and electrical cable
What country manufacters electrical cable?
Most industrialised countries manufacture electrical cable.
How to Convert electrical cable size to cable diameter?
Conversion of cable diameter to circle cross-sectional area and vice versa. Scroll down to related links and look at "Conversion of cable diameter to circle cross-sectional area".
What is Cable type electrical service?
cable tv
What size cable for 210 amps?
The recommended cable size for 210 amps would be at least 2/0 AWG (00 AWG) for optimal performance and safety. Make sure to consult the National Electrical Code (NEC) or a professional electrician to determine the exact cable size needed based on the installation requirements and conditions.
Can you use 0.75mm 2 core cable with 3 amp plug?
No, a 0.75mm 2 core cable is not suitable for use with a 3 amp plug. The 3 amp plug typically requires a higher rated cable to safely handle the electrical current. It is important to use the correct cable size and rating to prevent overheating and potential electrical hazards.
What is cable glanding?
A device designed to permit the entry of a cable into an electrical equipment and which provides sealing and retension. Cable well tightened with supporting of cable holding material into an electrical equipment or panels.
