0
Current is measured in amps so the setting on a multimeter would be A
Measuring current with a multimeter is only to be done by someone with training because it can be very dangerous
It is much better to measure current with a clamp meter
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
When testing for current draw your digital multimeter should be set on?
When testing the current draw your digital multimeter should be set on the current.
Can you measure the internal resistance of dry cell using multimeter?
Well, you do use a multimeter to measure it, but not directly. You need at least one other thing besides the multimeter and the dry cell. Here's a simple way to do it: -- Take a resistor. With the meter set to measure resistance, measure the resistor's value. Call that 'R'. -- With the meter set to measure voltage, measure the voltage of the dry cell. Call it 'V1'. -- Connect the resistor across the dry cell. Measure the dry cell's voltage again. Call it 'V2 ' this time . V2 will be less than V1 . The internal resistance of the dry cell is R times (V1 - V2) / V2
When measuring an unknown voltage with an analog VOM you should first?
For any value turn the multimeter to the highest scale in the value that you are measuring. By doing this you will not overload the meter by using a lower scale to measure a higher value.
If you attempted to read the voltage across a car battery with the multimeter accidentally in ammeter mode?
A multimeter when used on voltage, has a very high resistance/impedance to limit the current flowing through it. However when you set it to read current, it has a very small resistance to encourage the current to flow through the metre so can be measured. So ig you put a multimeter across a voltage source (in parrallel) when its set to current, you will normally destroy the metre. Although more expensive metres will have a fuse to protect the instrument should this occur. Hope this helps Always switch back, should you do this on the mains, you can quite easily set the metre on fire!! CB Eng
What is the pointer adjust in multimeter?
On a traditional analog multimeter, there is a screw on the face of the meter to adjust the tension on the pointer. It lets you set the pointer to zero when there is no current, just like zeroing the bathroom scales before you step on them.
When testing for current draw your digital multimeter should be set on?
When testing the current draw your digital multimeter should be set on the current.
How do you measure Automobile voltages?
A multimeter is the best tool for the job Set the voltage to 20 V. dc.
How do you use an analog multimeter to measure voltage?
Just set to AC or DC volts and probe the two points you wish to measure voltage across.
What should i set your meter to test a 12 volt car system?
Set your multimeter on the 20 Volt DC scale.
How can you measure a time delay fuse with a multimeter to determine if it is good or bad?
Set the multimeter for the "buzz" mode. This mode checks for electrical continuity. This means that the multimeter checks to see if there is a path for electricity to pass through. Some multimeters indicate it with a buzz, others with a light. Put one lead at either end of the fuse, and if the indicator (buzz or light) goes off, the fuse is good. If it doesn't go off, the fuse is broken. If you don't know how to set your multimeter on that setting, or it does not have one, set the multimeter to measure resistance. If the fuse measures a really small resistance, it is good. If it measures at a really large resistance, it is broken.
How would you setup an auto-ranging multimeter to measure 120 VAC?
If it is auto-ranging, there is no set-up - that's what auto-ranging means.
How would you setup an auto ranging multimeter to measure 120 VAC?
If it is auto-ranging, there is no set-up - that's what auto-ranging means.
How can you test a battery?
You can test a battery by using multimeter. Set the multimeter to the DC voltmeter setting and then place the leads of the multimeter across the leads of the battery. the multimeter will have a readout of the voltage.
How do you test speaker impedance?
You can measure speaker impedance with a multimeter set to the ohmmeter setting. Just place the multimeter probes across the two terminals of the speaker and you'll get the impedance value.
How do you check amp draw?
Amperage is measured by a multimeter. First determine the amperage rating on the multimeter. Next, select the appropriate setting on the tool. The next step is to set the range on the multimeter. Make sure to plug the leads into the appropriate terminals. Run the circuit through the multimeter to measure the current. Turn off the breaker, make sure the AC circuit is turned off, then rewire the circuit.
Can you measure the internal resistance of dry cell using multimeter?
Well, you do use a multimeter to measure it, but not directly. You need at least one other thing besides the multimeter and the dry cell. Here's a simple way to do it: -- Take a resistor. With the meter set to measure resistance, measure the resistor's value. Call that 'R'. -- With the meter set to measure voltage, measure the voltage of the dry cell. Call it 'V1'. -- Connect the resistor across the dry cell. Measure the dry cell's voltage again. Call it 'V2 ' this time . V2 will be less than V1 . The internal resistance of the dry cell is R times (V1 - V2) / V2
How to check register using multimeter?
first of all set multimeter to register section set the ohm rang as per the requirement (ohm, K ohm, or M ohm) set the both the end of multimeter wire at the both end of the register and note down the result which is displayed on the screen
