What would you like to do?
Hey Melissa==First remove the neg battery cable then the serpentine belt then the wiring for the altermator then the 2 bolts that hold it on. Make sure you have a schematic f…or the belt before you take it off. It should be on the fan shroud. If it isn't there, draw a schematic for yourself. Don't rely on memory. GoodluckJOE
How do you properly change the coolant and thermostat on a 2000 Chrysler Sebring convertible with a V6 2.5 liter MPI engine?
Usually removing the radiator drain plug or lower radiator hose. Make sure to have a drain pan large enough to hold the coolant. The thermostat is usually on the u…pper radiator hose, but shouldn't need replacing unless it is defective. Better yet, get yourself a Chilton service manual for the Sebring, they aren't expensive and well worth it.
10w30 or 5w30
Follow the lower radiator hose to the engine block. It is located below the housing that the hose goes over.
Answer The Sebring is a Chrysler product. Replace the crankshaft position sensor before beginning any diagnosis.
Chrysler doesn't use drain plugs on they're transmissions. so it isn't there
Tap them into the block then with long screw driver force it out of the block. Install the new one after you put sealer on it. use an installer so it does not get cocked in th…e hole.
A stereo wiring diagram for a 1997 Chrysler Sebring can be found in its maintenance manual. It can also be found in its repair manual.
Got this from another site (http://en.allexperts.com/q/Chrysler-Repair-807/2-5L-V-6-16.htm) It should answer your question - non-interference! Question Hello I have… a 1997 Sebring LXI with a going bad water pump I am about to have changed this coming weekend. I was wondering about the piston to valve clearance on these engines if they were designated non interference or interference? I would hate to have the pump totally fail on me driving to be fixed and my pistons slap my valves causing more damage. I also was trying to locate the hydraulic tensioner to replace my original one but cant find it online anywhere, have not asked at local dodge/mitsubishi dealer yet. Is that a part that should not fail or would changing it as well as the pulley and belt with the pump be wise? Had the car only a few weeks but not my first, had a 95 Avenger I loved, and a 97 eclipse with the 3.0 which is the same engine with different stroke. Naggingly having the water pump driven by timing belt is my only complaint due to the lack of consumer grade tools to get down to fix it.(Can not get crankshaft pulley bolt out on my own to change it!)Thanks for your time. Answer Hi Travis, The valve train is non-interference in design. The manual says the cylinder head has valve recesses to provide for valve clearance. On the tensioner, I have not heard of these or the pulley failing. Of course change the belt, unless it has less than 50K miles on it. I hope you have a Haynes or Chrysler shop manual to follow. If not let me know and I'll xerox and postal mail you the pages. Roland
cycle the key 3 times to read the codes.. it should shut the light off.. but if you still have a problem it will still come back on. if that doesnt work go t…o autozone or discount auto parts.. they have a obd tool that can read and clear diagnostic codes.. but if you have a problem it might not be a good idea to ignore the light.
It is called the upper water outlet.
Look under the exhaust manifold on the side of the motor facing the radiator. You have to drop the manifold and the oil filter bracket to change it.
engine have spark and fuel pressure and still will not start
Could anyone tell me why my motor is bogging down on my 1999 Chrysler sebring convertable 2.5 liter engine. i have replaced spark plugs and wires and the electric fuel pump.?
Check your cam shaft position sensor. I had a similer problem
Why does the engine idle very high after replacing the spark plugs on a Chrysler sebring 1996 2.5 liter convertable?
I recently had this happen when I forgot to plug in the idle air sensor at the throttle body. This also caused the check engine light to turn on. Also check for vacum leaks.
It is under the housing that the lower radiator hose hooks to on the engine. It is under the housing that the lower radiator hose hooks to on the engine.