A higher wattage HPS bulb may work with a ballast that is rated for a lower wattage bulb , but may appear to be dim and will not produce the rated light output. It is best to match ballast and bulb accordingly.
Yes you can, as i know the only difference between them is ignitor,so you only need to connect mh balast with ignitor,also power of ballast and bulbs must be the same
No. The bulb has to match the ballast wattage exactly. And you can't interchange different lamps (like metal halide) either. The ballast is specific to that wattage and lamp type. The bulb will either burn out quickly or just not work properly at all
Not recommended. It would work but shorten lamp life and may cause risk of fire. However, if you just wanted to check a lamp was capable of striking it would be ok for a few minutes. I've done the opposite in the past and used a 150w lamp with a 100w ballast. Works, but not good for any of the components, including lamp.
Yes, because the "higher" watt energy saver bulb (cfl) is actually a lower watt bulb than a standard (incandescent). Always look at the actual watts, not the 'light equivalent watts'. 11 watt low energy tube = 60 watts of old-fashioned light. More light, less heat!
No, a higher wattage INCANDESCENT light bulb uses more current than a lower wattage INCANDESCENT light bulb. Some CF and LED bulbs are rated by the amount of light that an incandescent bulb would produce, but they are also rated by the wattage that they use.
600w - the thicker filament has a lower resistance, which leads to a higher current and thus higher wattage
lower wattage bulb
No. The bulb has to match the ballast wattage exactly. And you can't interchange different lamps (like metal halide) either. The ballast is specific to that wattage and lamp type. The bulb will either burn out quickly or just not work properly at all
You can use a lower wattage bulb on a higher wattage fixture provided the voltage rating is the same and the bulb base is the same.
Make sure you are using a metal halide bulb and the ballast is matched to the wattage on the bulb. These both must be correct.
Not recommended. It would work but shorten lamp life and may cause risk of fire. However, if you just wanted to check a lamp was capable of striking it would be ok for a few minutes. I've done the opposite in the past and used a 150w lamp with a 100w ballast. Works, but not good for any of the components, including lamp.
Yes, because the "higher" watt energy saver bulb (cfl) is actually a lower watt bulb than a standard (incandescent). Always look at the actual watts, not the 'light equivalent watts'. 11 watt low energy tube = 60 watts of old-fashioned light. More light, less heat!
No, a higher wattage INCANDESCENT light bulb uses more current than a lower wattage INCANDESCENT light bulb. Some CF and LED bulbs are rated by the amount of light that an incandescent bulb would produce, but they are also rated by the wattage that they use.
When you want to use a MH bulb in an HPS ballast you must use a conversion bulb. It must be the same wattage as the HPS bulb
600w - the thicker filament has a lower resistance, which leads to a higher current and thus higher wattage
the higher the wattage is the hotter it gets
You should not use a higher wattage bulb in a lamp that says 40 watts. The higher wattage could cause the lamp to catch fire due to the excess heat and could cause you serious electrical problems.
Usually a CFL has two ratings. The first is wattage and the second is in mA I suspect the wattage is only the wattage of the bulb itself and the second is the actual current draw of both the light bulb and the ballast. They are not compatible. If you figure the mA and multiply times the voltage you will obtain close to the actual wattage of the combination of the bulb and the ballast. I have a 100 watt Feit BPESL25T which indicates it draws 25 Watts when it actually draws 47.5 Watts. Very close to the mA (400 x 120 VAC =48 Watts) indicated on the base. Almost all CFLs I've tested with my very accurate Fluke RMS meter draw twice the wattage they indicate. Not such a good deal.