How can you clean the water pipe line?
You can use one of the cleaners available in the market to clean the water pipe line.
1 person found this useful
Is it normal to have air in the return lines if the pipe pressure is OK and the skimmers are full of water?
I think it could be normal, if the pool is not losing water.. On my filter and pump, I have a valve, that when open, causes bubbles to come out of the low end jets, simulating the jets of a jacuzzi. When closed, there are no bubbles.. If the pool is losing water, then the appearance of bubbles in …the pump, or coming out of the jets could be due to air from from the outside which would mean a leak in one or more of the lines or at the fittings.. Also, I'm curious as to how one would "pressure check" a return line from the skimmer, the main drain or vacuum line since these wouldn't be under pressure from the pump.. Answer . If your pool is blowing air back into the pool through the return lines, it is caused by an air leak, on the suction side of the pump. Because the pump is above the water level of the pool, you will not lose any water. To check to see if you are sucking air at the pump, turn the pump on and take some dish detergent and squirt it along each plumbing fitting in front of the pump. Watch to see if any soap bubbles form in the pump housing. If so, you'll probably need to to replace those fittings, one of them is leaking. ANSWER:: The leak discussed above could involve both in and out fittings on the pump or it could be a leaking pump seal or a loose pump lid or lid gasket. The probable cause of this leak at the fittings is that the pump ran dry at some point in time causing the PVC fittings to become hot and shrink. . Pressure testing of the return lines involves plugging those lines at the pool and and pump. The people who do this sort of thing have a tool or tools to insert in the system and introducing air into those lines monitoring pressure loss in each particular line through a process of elimination. K (MORE)
Answer . \nsnaking the line is the best solution. you can also try taking the traps off and cleaning them. the best thing you can use is a little vegtable oil. this will help any stuck sewage to slide down the line.
you can try a garden hose down the vent on the roof use it like a drain snake with the water on
\n. \n Answer \n. \n. \nI have worked in many jurisdictions that allowed PVC water service piping, but you need to check with the administrative authority that enforces the plumbing code (if any) where you live.\n. \n Answer \n. \n. \nYes, most certainly. A recommended pipe would be …HDPE Class 16 and size of your choice (i recommend either three quarter inch or one inch pipe for adequate pressure) In most countries, a main line has to be underground, however, as soon as the pipe exists the ground at any given point it has to be non-metallic. As stated above check with your council or municipality regarding any queries regarding what material is allowed and how it must be installed. (MORE)
Answer . Let water run from every fixture for about 10 min. this should do it.
Answer . This is a TSB from GM it seems kinda odd but it may help Obtain a fixed antenna mast (new or used). Measure from the tip of the antenna a distance of 121 mm (4.75 in) and make a paint line or tape line completely around the antenna mast. This will be the depth stop reference. This ant…enna tool is to be reused. 2001 Aztek and 2002 Rendezvous Vehicles Only: Place the vehicle in the service stall over a hoist. Open the hood. With a light (a flashlight works best), look over the top of the engine between the back of the generator and the power brake vacuum hose attachment to the intake plenum. Look down to the base of the cowl to locate the evaporator case drain outlet. Insert the antenna mast tool described above into the evaporator case drain to the depth stop reference line on the antenna mast. Some force may be required the last 6.35 mm (.25 in) as you break away the flashing on the inside of the HVAC case covering the drain tube. (MORE)
COPPER TUBING TYPE "L" BUT make sure it is propelr drained in the winter months if freezing is possible
You can put a liquid pipe snake down your drain or put a hose down there
\nYou don't mention what sort of dirt you have in there, but whenever I have to stay in a hotel, I think about all the previous occupants, and I run vinegar water through the whirlpool before I put even one toe in. Just fill the tub as if you were going to use it, add at least 1 cup of vinegar, and… run the jets. Room service should be able to provide the vinegar - don't use bleach, which could damage the interior hoses. Vinegar will dissolve soap and kill off most bacteria. (MORE)
To clean a shower drain pour Dr.Pepper down it!!! Ideally water jetting as it will scour the waste lines to restore full flow as originally designed how to get rid of smelly bathroom drains . Water Jetting , snaking , Hydraulic shock wave . For cleaning nothing beats water jetting
If you have an internal water filter such as a whole house water pic water purifier, turn off the water supply to the house, then take the cannister off and remove the filter cartridge. After emptying the cannister fill it with regular unscented Clorox bleach. Put the cannister back on (without the …filter cartridge) filled with bleach and then turn the water back on. Remove all facet screens throughout the house and run the water. Continuing running the water at all facets, toilets, etc until the bleach smell is gone. You will be SHOCKED at the crud that comes out of the lines. You water pressure will improve greatly and the quality of water will improve. Make sure you remove all screens from facets first or they will clog up instantly. It also helps if you simultaneouly drain the hot water tank from the bottom (with a hose and a floor drain). This will improve the life of your hot water heater and give you hotter cleaner water. After all this is done put a fresh filter in your home water filter system. You'll thank me a million times. This should be done quarterly especially if you have well water. (MORE)
Soft Scrub using a Scotch-Brite abrasive pad. It removes those black lines great. I have a 20 X 40 in-ground pool & I clean the pool line every spring. Soft Scrub works great and does not mess up the chemicals in the pool. Hope this helps.
Ideally 1- Every change of the direction greater then 45 deg 2- at the base of the stack / leader 3- Every 50 feet 4- At the main house trap
There are a few different ways to do this. If it is a really thick hard limescale, you may want to use a commercial product like CLR or LimeAway to remove it. If it is not as bad, you can safely use a mild acid like lemon juice or vinegar. NO! specifically on the CLR label it says not to use on alum…inum, copper or brass (MORE)
Yes as it takes about 5 minutes to teach an 8 year old how to clean and properly solder copper fittings... The only problem is learning how to size the piping system to prevent erosion and learn to compensate for the coefficient of expansion per degree of temperature change to prevent a noisy system… (MORE)
rubbing alcohol and salt. small pipe, take a ziploc bag and put the rubbing alcohol and salt into the bag and shake it abck and forth. if its to big, put the mixture in pipe and close the holes and shake back and forth
What kind of pipe, the inside or outside, or a tobacco pipe? If it is copper pipe, you can use an emery sand cloth or steel wool.
You answered your own questions, if the two waters mix, then the output is diluted Germy water?
Water company builds dams filled with water. It is then cleaned by using chlorine put into pipes underground and linked to houses.
Not only can it be cleaner it should be water jetted every few years to make sure there is no residue hoar frosting.
brush it with a strong solution of acid, Becarefull for your eyes ETC and then hose it down.
Type K copper Ans 2 - You don't say for what purpose. - Generally if it's a well line from well or pump to the house there is special Poly/rubber well pipe . If it's lower pressure for a swimming pool or similar, then PVC pipe. -(both are cheaper and more durable than copper )
You do not have a demineralized water piping system. You have a device that demineralizes your water before it runs it through your pipes. There is a great difference. What you want to know is how to backwash your particular piece of equipment. You should have an instruction booklet that came with i…t when you purchased it. If you purchased it locally, call the local store. You may be able to purchase one locally. Otherwise, look on the piece of machinery for a manufacturer and a phone number. Get a duplicate instruction manual and then backwash it. (MORE)
Pipes containing potable (drinkable) water will be colored dark blue. Those carrying settled or clarified water will be colored Agua (lightish blue). Pipes containing raw water (not for drinking) will be colored olive green.
You need to know two important dimensions of the pipe: the length and the inside radius ( 1/2 the inside diameter ). From there, you plug the dimensions in to this formula: radius 2 x Pi ( 3.1416 ) x length . It is easiest if you ensure the dimensions are in the same format, such as feet or inc…hes. Here is a sample: The volume of a 50-foot long pipe with an inside diameter of three feet (1.5' foot radius) would be calculated as such: . 3 2 x 3.1416 x 50 = about 1,413.72 cubic feet of volume Now there is the important final step of converting cubic feet to gallons of liquid. There are about 7.48 gallons in one cubic foot. Since we know there are 1,413.72 cubic feet in the sample pipe above, we simply multiply 1,413.72 x 7.48 resulting in a maximum fluid volume of about 10,574.6256 gallons of water. (MORE)
Magic Eraser. Look for it at Wal-mart. Household cleaning isle. Picture of Mr. Clean on the front. Be gentle, first time I used it took some color out of liner. Has worked good since.
A bong or a water pipe is a special pipe. When a person smokes with a bong, they pull the smoke through the water in it. This makes the smoke not as hot. Most often, either tobacco or cannabis are smoked with it
Water is pumped in by the municipal water system or by your own pump and pressure tank.
All clean outs have to be accessible or what is the purpose of installing them? They can be placed behind an access door or under a floor plate
A very important aspect of owning or operating a kegerator is the cleaning of the beer lines. The whole system must be flushed at least every three weeks in order to maintain proper sanitation in your kegerator
Copper can be used for both hot and cold water. PVC is against many codes to use for domestic water supply because it can leach toxic chemicals into the domestic water supply. PVC is never used for hot water CPVC is used for hot
put it in a container full of rubing alchol and salt and shake it (not hard) and use a pipe cleaner for the rest
you have first to know the thermal conductivity of PPR that you are dealing with. normally, this is in range between 0.1 to 0.24 W/MK .then you apply this formula Q(IN WATTS) =Thermal Conductivity/MK)*A( surface area for the pipe M2 )temperature difference between fluid inside pipe and temprture of …pipe surface K)/(thickness of the pipe M) (MORE)
Your drains run slow when it is clogged even after many trials itwont stop.Also after you flush there may be sound of water for muchtime in such cases there is a need to call for sewerline repair services as they will inspect the blockagesby video inspection method and then decide which method to be… usedfor unclogging and apply the proper method thus problem is solved. (MORE)
I don't know about that, but you can just use rubbing alcohol and a toothbrush.
Why do you think there is a close link between low GNP per capita and poor access to clean piped water?
They can't afford clean sources of water such as a reservoir with clean pipes and therefore have to resort to using sources such as rivers or contaminated hand-dug wells.
Typically there is no colour code. Any fresh water line running into your house is drinkable unless you have a reuse system. DON'T DRINK FROM IRRIGATION some citys use reclaimed water (grey water I.e. from showers and washing your hands) for irrigation. ONLY Civilized countries use color codes … Countries with a bonifide plumbers guild and actually have a test for the masters licenses have color codes to prevent cross contamination of potable and non potable water systems. Depending on which code one uses will dictate the color coding OR metal tags stating safe water or Unsafe water. Round for safe triangle for Unsafe The reason for color coding is in high rise building there is a variety of piping systems such as fire suppression , potable , gray water, Combined fire systems (stand pipe and sprinkler) Fuel - gas - oil - steam and industrial lines such as pneumatic lines for controls The AWWA for example has under ground piping codes so in countries that have an established infrastructure workers know which piping are for utilities and waste and water supply rather then taking a chance of cutting into a wrong line (MORE)
Generally the best thing is air. If you can inject air into your tank or directly into the plumbing, it will knock a lot of the collected minerals off the pipes. Be sure to run the water off from an outdoor faucet or bath tub where it won't plug all your aerators.
There is no hot water inlet in a water heater. There is a cold inlet and a hot outlet. Yes it can be connected to the hot outlet depending on the jurisdiction. Check the plumbing codes in your area to be sure.
They can be run next to each other, but its good practice to try and stay away from them if possible.
All flux has acid so yes u can as long as u wipe it clean after u solder it will cause Ur joint to turn green
No. Regardless of what type of supply line you use between the house supply and the faucet it will be a compression fitting. Copper lines with a nut and ferrule or flexible ones are both compression and do not need tape or pipe dope.
When changing pipe sizes in the horizontal supply or return lines of a two pipe hot water heating system use?
Not sure what you're asking. Do you need to know size of piping or what kind of pipe to use?
Disconnect each shut off valve then blow through the pipe with a compressor - then drain and clean the tank, this should be done every 4-5 years to avoid this problem.
Calculate the (diameter of the pipe (D) divide by 2) squared X pi * length and this will give you the volume. eg Volume = (D/2) 2 X Pi X Length. (or R 2 X Pi X Length) (Use 3.14159265359 as an approximation for Pi.) In practice, 11/14 Times Diameter is used in lieu of (R 2 X Pi) as a quick and …dirty but near enough approximation. (MORE)
Put a filter system on it! Some types have inline filters for them, not the huge filters.
Make sure the sewage pipe is in good repair and has NO leaks thenextend it to a facility where the sewage can be treated (turnedinto good water by mixing it with air to let the good bacteriabreak down the sewage). It is possible to turn sewage into harmless, good products and tomake the water clean …again. This is a natural process (otherwiseall the water on earth would be bad) and it is possible to makethis process happen faster using waste treatment methods. (MORE)
A lining in a pipe, placed there to protect the material of thepipe from the contents that will be passing through the pipe.
Yes. Allsorts of debris, nests, critters, etc., can accumulate in a pipe before it is installed. If the pipe is to carry potable water, it should be a free as possible of that stuff before being installed.
Sure hot water heaters use them and they take the heat. However, this might not be up to building codes. Either check thebuilding codes for your area, or be aware that you might have toreplace it again in the future.