Answer for USA, Canada and countries running a 60 Hz supply service.
A four blade range plug is the new code. What should be done is to change the three blade receptacle to a four blade receptacle. The only difference in the receptacle wiring is that the position of the neutral wire and the addition of a ground wire being brought out to the range on a separate blade to match the ground wire on the plug. Turn the circuit breaker that feeds the range to the off position. Opening up the receptacle you will find now, two hot wires to the outside blades and a neutral to the center pin. Look in the back of the range receptacle's junction box and you will see a ground wire wrapped around a screw that grounds the dryer feed wire. From this ground wire add an extension of six inches. This new wire then connects to the fourth terminal on the new four blade receptacle. Looking at the new receptacle you should have the two hot wires on the outside terminals X and Y, white (neutral) W blade and the newly installed ground wire to the U shaped ground G blade. This receptacle is a NEMA 14-50R, 3 pole 4 wire grounding receptacle.
Before you do any work yourself,
on electrical circuits, equipment or appliances
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Green or copper ground wire goes to the round connection on the plug or ground screw on stove. White neutral wire goes to the connection opposite of the ground or neutral on the stove. The red and black wires are connected to the other 2 connections or hot connections on the stove. Connect either one to either connection makes no difference.
Green or copper wire is ground
White is neutral
Red carries 120 volts
Black carries 120 volts
Answer for USA, Canada and countries running a 60 Hz supply service.
You would have to change one or the other so they are compatible.
<<>>
You don't. In your situation the three wire range cable should be changed to a four wire. Instructions should come with the new cord. Open up the electrical access panel on the back of the range. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the range. When installing the new four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the range. This is the attachment point for the fourth green ground wire from the new range cord assembly.
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Note: There are comments associated with this question.
were is the answer to my question
wire the ground and common together
As the waffle maker is a totally resistive load there will be no problem using the different supply.
10 AWG.
If all the components are rated to 220V, yes. Keep in mind that if the appliance was designed for 110V it may arc if 220 is run through it. If you don't know the device can handle 220V, don't run it at 220V. Chances are it was manufactured cleaply and cannot handle the extra voltage.
Your ballast should show two wires for supply side of ballast. Make sure that neither side of this is grounded to the light and connect the 220 V from your breaker to these two wires and then connect a ground to the chassis of the light from the panel.
It would involve some electronics work but it could be done. Might add that it could be more expensive than just buying the proper power supply. Use Use 220V 60hz motor to run 110V 50hz Generator.
nothing
If you connect 110V xbox one to a 220V outlet, only the power supply will burn and not the Xbox one.
of course. go to the market and buy a transformer. It will convert a 110V supply to a 220V supply.
This bulb is very likely to be burn out since the 440 supply voltage is very higher than it's rated voltage.
As the waffle maker is a totally resistive load there will be no problem using the different supply.
No
Typically, a 100 ohm resistor is used to connect a 1.5 volt led to a series 220v ac adapter. Many LEDs can be connected into a string using the resistors.
Yes just connect any line to neutral you have 230volts already.
10 AWG.
Short answer: No. (unless you like ruining motors) Longer answer: Not really, but there are some motors that can be re-wired so that instead of 440v they will run on 220v. However, this is not that common. Conclusion: Check the motor to see if it is dual-voltage on it's nameplate. If it is, you can re-connect it to work on 220v. If it is NOT a dual-voltage motor, you will absolutely ruin it if you connect it to 220v.
If all the components are rated to 220V, yes. Keep in mind that if the appliance was designed for 110V it may arc if 220 is run through it. If you don't know the device can handle 220V, don't run it at 220V. Chances are it was manufactured cleaply and cannot handle the extra voltage.
DC 12V power supply can convert 110/220V AC power source to 12V DC.