0
It's driven out left to right using the appropriate roll pin punch. Bolt and its parts can be removed and receiver cleaned.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
Can you dismantel the barrel of a hawkens 50 cal?
Depending on the maker you can remove the breech plug and of course the sights and underlug. It is not an easy task to remove the plug and without proper tools usually results in a buggered up barrel or plug. You would need a barrel vise and a breech plug wrench, some heat and penetrating oil. I would recommend taking it to a gunsmith in your area.
What is a safe way to unload a muzzleloader?
removing the breech plug
What is the thread size of the breech plug in a knight lk93?
Contact the company at knightrifles.com
How do you take off the stock of a Ithaca defense model 37?
Take a screw that will fit tight in the hole in bottom screw it in tight and pull out the plug with a long screwdriver remove the screw
How do you disassemble a marlin mls-50?
remove the 2 bolts for the stock and then the 2 bolts that hold the trigger onto the barrel. Remove the large cap on the back of the barrel with a large screw driver. Be careful to hold it in place when removing it because it is under spring pressure. Once removed, remove the firing pin, cap, and two springs. Then cocking lever should be loose now so it will come out. You can now use the breech tool to remove the nipple and breech plug. reverse to assemble.
Is the breech plug for a Thompson center new englander removeable?
The short answer is yes it can. I'm a muzzleloader gunsmith and T/C dealer of 30 years. I can remove it with a special tool, but I wont and neither should you. There is no reason to ever remove a breech plug from any traditional muzzleloader. Removal is not necesary for cleaning and I dont see any other reson to remove one. Of the few I have taken off, some took over a week and a six foot cheater bar to get off. Some just wrung off. T/C used to sell a tool for removing the breech plugs but customers using them were screwsing up the threads and sending them in for warrenty work. After that, about 1980, they started putting them on so tight and with so much industrial locktite, they are almost impossible to remove. Once again, I've never encountered a need or reason to remove one. RamblinMan
How do you disassemble a marlin MLS 50 muzzleloader?
remove the 2 bolts for the stock and then the 2 bolts that hold the trigger onto the barrel. Remove the large cap on the back of the barrel with a large screw driver. Be careful to hold it in place when removing it because it is under spring pressure. Once removed, remove the firing pin, cap, and two springs. Then cocking lever should be loose now so it will come out. You can now use the breech tool to remove the nipple and breech plug. reverse to assemble.
How do you disassemble a marlin MLS-50 muzzleloader?
remove the 2 bolts for the stock and then the 2 bolts that hold the trigger onto the barrel. Remove the large cap on the back of the barrel with a large screw driver. Be careful to hold it in place when removing it because it is under spring pressure. Once removed, remove the firing pin, cap, and two springs. Then cocking lever should be loose now so it will come out. You can now use the breech tool to remove the nipple and breech plug. reverse to assemble.
How do you remove the plug from a model 37 Ithaca shotgun?
Pull pump action back. screw the knurled part at end of stock to loosen it. Remove barrel. Turn knurled part all the way off and plug and spring should come out. Replace spring and replace knurled part. Replace barrel and you're ready.
Is 1974 huntsman 45 cal black powder breech plug unsafe?
Impossible to answer via the internet. Take it to a gunsmith.
How do you change transmission fluid for mazdaspeed protege?
remove the fill plug, then remove the drain plug, then reinstall the drain plug and add fluid until it comes to the level of the fill plug. remove the fill plug, then remove the drain plug, then reinstall the drain plug and add fluid until it comes to the level of the fill plug.
How do you remove a spark plug out of a 1985 Honda xr200r dirt bike?
Remove the rubber cover and plug lead from spark plug. Using a bike plug spanner [cheap at your favourite auto supermart] remove plug.
