A 'leading' power factor indicates that the load current is leading the supply voltage. Since power factor is the cosine of the angle by which the load current either leads or lags the supply voltage (i.e. the load's phase angle), a cosine of 0 corresponds to a phase angle of 90 degrees.
So, a power factor of 0 (leading) indicates that the load current is leading the supply voltage by 90 degrees, which means that the load must be purely capacitive.
IT means when torque is not zero even at zero power factor?? are you in IPU??
When you have a Power Factor less than 1 the voltage and current waveforms in an AC circuit are out of phase. Therefore at any given instant of time the work being done or energy being expended is calculated by multiplying the current x voltage. This reduces the wattage at any instant of time. When the Power Factor is one the instantaneous multiplication of the current and voltage would yield the maximum value with the waveforms in phase. This is much easier to see with a picture, but imagine a square wave for both voltage and current. Say for half the cycle the current is 2A and Voltage 3V and for the second half of the cycle both are zero. So for 1/2 the cycle the watts generated are 6 watts and zero for the second half of the cycle. Now if the two waveforms were 180 degrees out of phase the voltage would be zero when the current was 2A and the current would be zero when the voltage was 3V for zero watts. In this case the Power Factor would be zero.
If that's y to the zero power, the value is 8.
Power factor measures the phase difference between voltage and current. If they are in phase the Power Factor is one. If the current and voltage are out of phase the power factor is between zero and one. You can describe the PF by saying the current lags the voltage with a PF = .8 or the voltage leads the current with a .8 PF.
ratio between true power and apparent power is called the power factor for a circuit Power factor =true power/apparent power also we conclude PF=power dissipated / actual power in pure resistive circuit if total resistance is made zero power factor will be zero
Per factor is 1 when reactive power is zero.
Pure inductors consume and produce power, just like other reactive devices. The difference is that the current is not in phase with the voltage, resulting in the waveform of the power being oscillating about zero, with a net mean power of zero. In this "pure" case, the power factor is zero, but that does not mean there is no power - its just that the power "reading" is unsophisticated and not compensating for power factor.
IT means when torque is not zero even at zero power factor?? are you in IPU??
zero volatge regulation means the terminal volatge of transformer at full load on a given power factor become equal to the rated teriminal volatge of transformer , it happens only for leading power factor in transformer
The power factor (cosine of phase angle) of pure inductor is zero because the phase angle between current and voltage is 90 degrees .If the value is substituted in the formula It will be zero.
When you have a Power Factor less than 1 the voltage and current waveforms in an AC circuit are out of phase. Therefore at any given instant of time the work being done or energy being expended is calculated by multiplying the current x voltage. This reduces the wattage at any instant of time. When the Power Factor is one the instantaneous multiplication of the current and voltage would yield the maximum value with the waveforms in phase. This is much easier to see with a picture, but imagine a square wave for both voltage and current. Say for half the cycle the current is 2A and Voltage 3V and for the second half of the cycle both are zero. So for 1/2 the cycle the watts generated are 6 watts and zero for the second half of the cycle. Now if the two waveforms were 180 degrees out of phase the voltage would be zero when the current was 2A and the current would be zero when the voltage was 3V for zero watts. In this case the Power Factor would be zero.
nothing
1
If that's y to the zero power, the value is 8.
Power factor measures the phase difference between voltage and current. If they are in phase the Power Factor is one. If the current and voltage are out of phase the power factor is between zero and one. You can describe the PF by saying the current lags the voltage with a PF = .8 or the voltage leads the current with a .8 PF.
Zero degrees.
ratio between true power and apparent power is called the power factor for a circuit Power factor =true power/apparent power also we conclude PF=power dissipated / actual power in pure resistive circuit if total resistance is made zero power factor will be zero