Where is the fusebox located in a 2003 Chrysler sebring?
On the '03 Sebring, there is a panel on the left end of the dashboard. You have to open the driver door to see it. Just pull it straight out. You may feel some resistance but it will come out. There is also another fuse box under the hood on the right side of the engine compartment. It is a black box toward the front. There are two clips holding it. One on the right and left. Unclip it to take off the cover. The owners manual shows both fuse boxes and what each fuse or relay is for.
4 people found this useful
2.4L On the engine end of the upper rad hose. When replacing itmake sure the spring goes toward the engine 2.5L it is under the housing that the lower radiator hose hooks toon the engine.
Answer . I changed the thermostat on my '99 Sebring Limited 2.5 l. convertible today (5/4/2005). As someone else stated, it's a tedious job but not impossible. Look underneath the pressure cap/fill pipe. There's a separate casting bolted to the block. It is held in with three bolts having 12 …mm heads and one bolt that also attaches a wiring harness clamp. For whatever reason that bolt has a 13 mm (1/2") head. In order to access the casting you will need to remove the air intake duct work. I did not remove the transmission dipstick/fill tube, but that would make the job much easier. I also did not remove any coolant hoses. To do the job you will need 10, 12 & 13 mm sockets plus an assortment of various length extensions and u-joints. A magnet on a rod will no doubt be very useful. Be careful when reassembling it to make sure that the thermostat is properly seated. The whole job took me about 1 1/2 hours and a few skinned knuckles. \n. \nSam Yardumian (MORE)
Sparkplug changing safety tips. . \nIt depends on which engine your sebring has. The sebring coupes have a Mitsibishi engine that is different than the convertables and sedans. Be careful of loosening any fuel lines that may be under pressure. The pressure is enough to inject fuel through your sk…in. Loosen fuel cap,pull relay for fuel pump, start motor and run till it runs out out of fuel, replace fuel cap,relay, and then disconnect negative terminal on battery before anything is disasimbled for your own safety. Public libraries are alot easier to get the info. from for the do-it-yourselfers than alot of high payed mechanics. Even if you pay to have repairs done, it's nice to know what is being done to your car. (MORE)
For a 2003 sebring convertible, raise the hood. On top of the metal support frame at the headlight assembly, there are two screws that hold the full head light assembly to the frame. Remove the two screws. Now the headlight assembly is loose and can be pulled out far enought to remove the lamp. Turn… the lamp holder counter closckwise about a half turn or so and remove the lamp. Replace all in the reverse order. Don't touch the new lamp with your bare fingers. Oil from your skin will cause the lamp to turn black. (MORE)
Answer . \nShould be on the back side of the multi-function switch. Remove the upper shroud and it will be the little black box to the right of the emergency flasher button. Push it towards the front of the car and it will slide out.\n. \nAnon
Answer . \nIf simialar to the Matrix, one is under the hood next to the driver's side fender, and another is under the dash just in front of where the driver's left knee would be. Have to get on your back to access it. Both have a removable black cover.
If it is on the 2.7 litre engine, the thermostat is located in the left lower front of the engine. Follow the lower radiator hose from the radiator up to the engine block, just under the alternator and you will find the thermostat housing. The housing or fitting at the top side of the engine, left o…f the intake manifold is the air bleed and temperature sensor housing only. (MORE)
Answer . It is located at the passenger side behind the oil pan. You need to be under the vehicle to watch it .
Answer . under the dash. if you can find the blower motor then it should be right above that
Answer . More than likely 5w30. Look in your owners manual or call a local Chrysler dealer to be sure.
the starter is located between the exhaust manifold and the engine block. It is only visible from the bottom of the car and is protected by a heat sheild.whoever designed this wasn't thinking of the do it yourselfer because the motor mounts will probably have to be removed to get the beast out, or w…orst.I remember the good out days when a job like was a fifteen minute inconvenience. (MORE)
Answer . it should be just to the right of the passenger side fog light inside the front bumper.
Answer . When looking at the engine, the thermostat is located underneaththe the radiator fill cap. There are 2 bolts to remove. Be carefulnot to rip or tear the gasket or make sure you have areplacement. On the 2.7L, the thermostat is under the housing where the lowerradiator hose hooks to the e…ngine. (MORE)
On the inside of the fuse box covers is a diagram of the fuse box with the fuse locations and sizes.
Answer . Look at the ends of the dash board with doors open little access panels. --------------------------------------------------------------------------------------------. There si also a fuse block under the hood. TechJK
There are two: one in the engine compartment near the air filter box and the other on the driver side underneath the dash.
2000 Chrysler sebring,to replace battery car must go to dealer to have fender removed so new battery can be installed, they charge $169.00 for this work. Or they remove it through the hatch in the wheel well. Turn wheel fully left. Disconnect terminals. Remove the panel from the left wheel wel…l. Remove the battery hold-down (MORE)
Answer . Under the hood to the right of the battery. Squeeze the clips and lift the lid of the fuse box. Inside the lid it tells you what each fuse is used for, it's a bit hard to read black raised letters on a black plastic backround.. Also inside under the dash on the extreme left side beside …the computer access port are more I am told. I think you remove the plastic cover held in by two screws. I never took it off but since my defrosters don't work front or rear or heated mirrors I hope to find the fuse in there. (MORE)
Answer . \non a 2.5l it is mounted on the intake plennum in the back against the firewall
I'm looking up this site to see how to get the starter out. It is located in front center of the engine above the front motor mount. You can see it from under the car looking up between the front catalytic converter and the engine block. Good luck getting to it.
You will need wrenches and possibly an oil filter socket or large channel locks, and of course a drain pan. Locate the oil drain plug in the oild pan and remove it. (hot oil will come out into the drain pan at this point ) when it is finished draining (dripping) reinstall drain plug snugly. Locate a…nd remove the filter by using either the filter wrench or the large channel locks. (make sure the old rubber ring gasket on the oil filter is in the filter still and not stuck to the engine block mating surface) install the new filter hand tight only. Add 4 qts of engine oil to the engine through the cap marked for engine oil. Start the vehicle check for leaks. Shut off the engine and check the dispstick and add oil (if needed) to bring the engine oil level up to the full mark on the stick. (checking oil must be done on a level surface) reinstall cap...Done. (MORE)
5w30 Engine oil.... "Engine oil" -- funny, but not an answer. I have a Chrysler Sebring convertible with the 2.7 engine that just turned over 200,345 miles. A mechanic told me my engine is a flawless as it is because I have been using Mobil One oil in it for the past 5 years. - Howard
2003 Chrysler Sebring idle has increased to aprox. 1500 rpm. Would the problem be with the idle control valve Where is valve located?
It is located just above the dist below the throdle body. On a 3.0 2.7 about the same
well you didnt really give too much information about what kind of motor your car has so let's say it's a 2.7L lx model?. the thermostat is located about a foot down on the front of the motor, but still behind the radiator. it's pretty easily accessible. be careful if you're trying to replace it yo…urself tho, because sebrings has pretty complicated cooling systems. if you testdrive and the problem isn't fixed, the pressure's liable to burst a small hole in the radiator, and then you're looking at $900 parts and labor, just for them to try to replace the water pump, which means the timing belt kit as well. it most likely is the head gasket... sorry for the bad news. (MORE)
The owners manual for a 2003 Chrysler Sebring LX is found at anautomotive shop. It can be found and purchased from the dealershipas well.
It is inside the passenger side of the engine. It is driven by thetiming belt or chain.
For the 2.7l engine, the thermostat housing is all one piece. The housing is located under the alternator and attached to the engine block.
There is no such part. The computer uses inputs from numeroussensors to decide how to control idle speed with a airflow controlvalve on the throttle body.
The EGR valve is mounted on the rear of the engine. It is connectedto two pipes, just above the bell housing.
Remove driver side front tire. remove inner fender liner. Battery is inside the front fender wheel.
First, open your hood and prop it open using the hood support rod. Stand in front of the vehicle, looking towards the engine. Now look on the top and slightly behind the headlight(s) and you will see (2) 8mm bolt heads that run straight up and down, one on each side of the light housing. Remove both… bolts and pull the headlight assembly straight forward to remove it. Now you will see the bulb retaining ring, do not turn this yet. First, unplug the wiring connector from the bulb, then twist the locking ring counterclockwise until free. Remove the old bulb and replace with the new bulb. EXTREMELY IMPORTANT--DO NOT TOUCH THE GLASS ON THE BULB, HANDLE THE NEW BULB WITH A CLEAN RAG/ PAPER TOWEL/ NAPKIN. Any finger prints/ grease on the new bulb will result in a hot spot on the new bulb and it will burn out again. (MORE)
On the right side of the engine compartment next to the air cleaner. It is a large silver box.
You hook the charger cables to the red and black jump start postsunder the hood.
facing the front of the vehicle with hood up, it can be found to your right just inside radiator housing.
The oil pressure sensor is on the back of the engine, above the oilpan, behind a heat shield.
4 cylinder : it is under the housing that the upper radiator hosehooks to. 6 cylinder : It is under the housing that the lower radiator hosehooks to.
2.4L should be located at the engine end of the upper radiator hose On the 2.7 motor the thermostat is located at the engine side of the lower radiator hose
You have a leak in the cooling system. Could be water pump, hoses, radiator, headgasket, etc.
It is located on the right side of the engine (facing the engine ) near the the fuse box.
directly under the drivers side dashboard. the horn is in the frontleft just behind the headlights
The speedometer signal is all electronic. There is no cable. Thesignal comes from speed sensors. The speedometer signal is all electronic. There is no cable. Thesignal comes from speed sensors.
It is on the front of the engine, behind the engine mount. It is on the front of the engine, behind the engine mount.
Park vehicle on a level surface and drain the oil and change the filter. Pour in 4.5 quarts of the correct weight oil. Start the engine and run for 2 minutes. Shut down and wait 30 minutes. Check the oil level and add as necessary to reach the full mark on the dipstick. You now know the capacity.
The fuel pump is inside the fuel tank. The fuel pump is inside the fuel tank.
Four cylinder, on top of the valve cover. Six cylinder, it is builtinside the distributor. Four cylinder, on top of the valve cover. Six cylinder, it is builtinside the distributor.
2.4L, yes. 3.0L, yes. 2.7L, no - is a chain. 2.4L, yes. 3.0L, yes. 2.7L, no - is a chain.
The timing chain is inside the passenger side of the engine. The timing chain is inside the passenger side of the engine.
They are under the coils in the center of the valve covers. They are under the coils in the center of the valve covers.
Front center of the engine, behind the motor mount bracket. Front center of the engine, behind the motor mount bracket.
2.7L V6, it is under the housing where the lower radiator hose hooks to the engine. 2.4L, it is under the housing where the upper radiator hose hooks to the engine.