0
The best way to do it is to go get custom fit, there you can accurately compare both shafts and see which one best fits your game. Or you could ask a local Golf shop or local pro if you could borrow one of each and try it on the course. Maybe even your friends could help you out.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Whats the difference between a graphite and a steel shaft for golf clubs?
Graphite shafts transmit fewer vibrations up the shaft to the golfer's hands than do steel shafts. This might be good or bad, depending on your skill and your desire. You might want that added feedback that steel shafts offer - or you might be tired of your hands stinging so much on mis-hit shots. The biggest and by far most important difference between steel and graphite shafts is this: graphite shafts are lighter than steel shafts. So clubs that have graphite shafts will be lighter than otherwise identical clubs that have steel shafts. The difference in weight between graphite shafts and steel shafts will translate, for most golfers, into an additional 2-4 mph of swing speed with graphite. And that could mean an extra 6-12 yards of distance with a graphite shaft, compared to a steel shaft. Steel shafts are less expensive than graphite, so the same set of clubs will cost less with steel shafts than with graphite shafts. Steel shafts were once considered much more durable than graphite. That's not s
How do i trim a golf shaft?
For a steel shaft, a tubing cutter is the best way. You get a clean cut perpendicular to the axis. You'll need to have a hardened wheel that can handle the stainless steel. For high production volume shops a cutoff saw with an abrasive wheel is typical.For graphite, a hacksaw with an abrasive blade works well.If you want to know how much to cut off, you can get basic recommendations from whoever sold you the shaft.
Can you change steel shafts to graphite?
AnswerYes, unless you're a pro. A hobbyist does not have the swing control necessary to adjust to the difference required for each shaft. The extra flex in a graphite shaft will require a different swing. Playing golf well requires good repetition of proper swings.You want graphite in your woods and perhaps in your Hybrids. Graphite in irons can be spooky as in sometimes the ball will go long and sometimes short. It is more difficult to control the distance with graphite iron shafts. Steel is more predictable.
I want to reshaft my callaway x-18 steel shaft clubs to graphite what would be the best shaft to use?
If you want a high quality shaft, you should look along the lines of UST, Grafalloy, Aldila or Mitsubishi. I cannot tell you which one you should get because I do not know your game/age/ability etc. The best thing to do is to go get custom fit and try out a few different shafts. Nearly all shafts have different kick points and produce different launch angles. The problem with Callaway clubs though is that shafts go through the head to the bottom of the club, some golf shops may actually shy away from fitting new shafts to these.
Looking to buy a good pool cue for under two hundred dollars have any suggestions?
If you want something made in the USA, check McDermott or Viking. If you want something a bit less expensive, try Players. If you want a cue with a graphite shaft, try Cuetec. These are all good brands with good warranties.
How long is a standard shaft on a golf driver?
The standard length of a mens 3 wood is around 41-42 inches long. You will find that the length of shaft varies from manufacturer to manufacturer. You can also get custom fit where they may take an inch or two off your shaft.
How do you know which Graphite Shaft is right for you?
The level at which you play at, will determine how accurate you want to be in relation to the correct shaft for you. In the very simplest of terms, if you are a beginner you will want a regular high kick point shaft, this will help you get the ball in the air easier and square the club face easier. If you have played for a while and have a reasonably quick swing speed (Around 95mph) you would want a stiff shaft, this is where the distance starts to come in. If you are an older player, with a slow swing speed you will want a senior shaft, these are very flexible and help you get the ball in the air. Similarly, Ladies flex shafts help get the ball in the air but are a bit lighter than a senior mens. Kick point is quite important, a low kick point gives a lower launch and similarly a higher kickpoint gives a higher launch. Shafts come in a variety of weights, lighter ones feel whippier and most players prefer a slightly heavier shaft. Generally the stiffer the shaft the heavier it is. The best thing to do, is to go to a good golf shop and get custom fit for the right shaft, it will tell you spin rates and launch angles, getting a good launch angle and spin rate is where are the distance comes from. If you get a shaft that is too strong for you, you will block it, and if you get one which is too weak you will hook it.
Can you bake the lead of a pencil?
Well yes...but why would you want to? The lead in a pencil is composed of graphite, not actual lead. Graphite is a soft form of carbon and very greasy. See link.
What mineral is found in coal graphite and diamonds?
The answer you want is carbon.
How sticky is graphite?
Very (NOT) Graphite is in fact known for being the exact opposite to sticky. It is used as a lubricant in many areas where you want parts to move even more smoothly than oil can do.
What do you look for in a good lacrosse shaft?
Depends on if you are attack, middie, or defense. For attack, ideally, you want something very light to easily shoot and pass with. Look for a titanium/ hybrid alloy shaft. For middie, you want a balance of strength and weight, strong, kinda heavy to through checks, but light enough to shoot and cradle with. Look for a hybrid/ composite material shaft. For defense, you want something really strong to hold up to checks. Weight for defense is up to the player; heavy to check better, or light to pass and cradle better with. Look for a hybrid/ steel/ aluminum shaft. But, ask around your team or friends, see what other people have, ask to use their stick, and base your judgement on how the stick feels for you.
What to use to cut a steel golf club shaft?
There are several options ranging in price. 1) best options is a cutoff saw with a metal cutting blade/disc. Cuts shafts like butter. Unfortunately, it is also the most expensive option, but the only option for a high volume shop. Also works on graphite shafts. 2) If you are a home tinkerer like me, you can use a standard Hacksaw, but pick up a Tungsten Carbide wire cutting blade (usually $2-$5 at any hardware store). Then wrap masking tape around the shaft at the approximate length you want to cut it. Measure the length and mark it on the tape. Using a shaft adapter (also about $2 at a golf store) and a bench vise (hopefully you already have one, but if not, you can use a clamp and any hard surface) secure the shaft as close to the cut line as possible for stability. Now, slowly draw the blade across the tape so that it is just above the cut line. The groove in the tape should hold the blade in place as you start cutting. Apply more pressure as you start sawing and cut the shaft. If you have belt sander, I'd also recommend sanding the end to avoid burrs which can be hard on your grips. Also works on graphite shafts. 3) A standard hacksaw blade, but it is much harder to cut straight, and they wear out much faster than the carbide blade. Don't try this on graphite because the teeth will catch on the fibers and could de-laminate the end of the shaft. 4) A tubing cutter makes a very clean cut. Use one with a hardened cutting wheel. Some wheels are only hard enough to cut copper tubing. Not for graphite, it will crush it rather than cut it. 5) A hand held high speed cutter. An air powered one can be found for fairly low cost. It's like as small cutoff saw. Also works on graphite shafts.
