There is really no wattage in "rms". RMS means only that the calculation goes P = V * I where you use V-RMS and I-RMS. In common use, the terms "RMS power" or "watts RMS" are erroneously used to describe average power.
Power is defined as a function of the current and voltage, AND, in AC (Alternating Current) circuits any phase shift between the applied voltage and the resulting current.
For pure RESISTIVE circuits (incandescent lamps, electric stoves, electric space heaters, etc.) operating on DC (direct current), the current in amperes is equal to the DC voltage divided by the resistance (in ohms) of the "load".
In circuits containing inductive "loads" (Transformers, motors, etc.) and operating on a pure sine wave power source, the power is defined as the RMS voltage times the cosine (trig function) of the phase difference between the voltage and the resulting current. This phase "angle" will never exceed 90 degrees.
So to properly answer the question, one needs to know if the power applied is AC or DC, and what is the applied voltage.
Assuming 120V, 5000W is 41.66A bassed on the formula P = V * I P = Watts
V = Volts
I = Amps
The formula you are looking for is I = W/E, therefore 5,000/120 = 41.66 amps.
To find amps if watts and volts are known, use the formula; watts / volts = amps or 5000 / 240 = 20.83 amps
VA and Watts are different names for the same thing but denote different uses. Watts is actual power and VA would be used for potential power. So 5kVA = 5000 Watts. kVA = volts x amps / 1000 kW = volts x amps x power factor / 1000
watts = volts * amps--> Amps = watts/ volts therefore; 2000/220= 9.09 amps
9000 watts is zero amps. Amps are the product of amps times volts. Without a voltage stated an answer can not be given. I = W/E, Amps = Watts/Volts.
Watts = Volts * Amps Therefore: 70 Watts / 13.8 Volts = 5.07 Amps
To find amps if watts and volts are known, use the formula; watts / volts = amps or 5000 / 240 = 20.83 amps
There is no direct conversion between the two. You need to know voltage to calculate amps. This is the equation: P = V * I Where: P = Watts V = Volts I = Amps
5000 watts
5000 (watts) /120 (volts) = 41.6 amps , but to be safe you should allow 1000 watts margin for peaks, so 4000/120 is 33.3amps, although peaks might sometimes get higher than 5kw
VA and Watts are different names for the same thing but denote different uses. Watts is actual power and VA would be used for potential power. So 5kVA = 5000 Watts. kVA = volts x amps / 1000 kW = volts x amps x power factor / 1000
To answer this question the voltage of the immersion heater is needed. I = W/E.
watts = volts * amps--> Amps = watts/ volts therefore; 2000/220= 9.09 amps
21.739 a 21.739 a
9000 watts is zero amps. Amps are the product of amps times volts. Without a voltage stated an answer can not be given. I = W/E, Amps = Watts/Volts.
There are zero watts in 730 amps. Watts is the product of amps times volts. As you can see without a voltage no answer can be given.
Watts = Volts * Amps Therefore: 70 Watts / 13.8 Volts = 5.07 Amps
Amps, volts and watts are interrelated, but you need to do a little math. Amps * Volts = Watts