chair

Vincent's Chair by Vincent van Gogh

Five three-legged chairs around a low-legged table from Sliven 19th Century Lifestyle Museum

A chair is a raised surface used to sit on, commonly for use by one person. Chairs are most often supported by four legs and have a back^[1][2]; however, a chair can have three legs (in a triangle shape) or could have a different shape depending on the criteria of the chair specifications.^[3]

A chair without a back or arm rests is a stool,^[4] or when raised up, a bar stool.^[5] A chair with arms is an armchair^[6] and with folding action and inclining footrest, a recliner. ^[7] A permanently fixed chair in a train or theater is a seat^[8] or airline seat;^[9] when riding, it is a saddle^[10] and bicycle saddle,^[11] and for an automobile, a car seat^[12] or infant car seat.^[13] With wheels it is a wheelchair^[14] and when hung from above, a swing.^[15]

A chair for more than one person is a couch, sofa, settee, or "loveseat";^[16] or a bench.^[17] A separate footrest for a chair is known as an ottoman,^[18] hassock^[19] or pouffe.^[20]

History of the chair

Early twentieth century chair made in eastern Australia, with strong heraldic embellishment

The chair is of extreme antiquity and simplicity, although for many centuries it was an article of state and dignity rather than an article of ordinary use. "The chair" is still extensively used as the emblem of authority in the House of Commons in the United Kingdom^[21] and Canada,^[22] and in many other settings.

Committees, boards of directors, and academic departments all have a 'chairman'.^[23] Endowed professorships are referred to as chairs.^[24]

In fact, it was not until the 16th century that it became common anywhere. Until then the chest, the bench and the stool were the ordinary seats of everyday life, and the number of chairs which have survived from an earlier date is exceedingly limited; most examples are of ecclesiastical or seigneurial origin.^[25] Our knowledge of the chairs of remote antiquity is derived almost entirely from monuments, sculpture and paintings.^[26]

Chairs were in existence since at least the Early Dynasty Period. They were covered with cloth or leather, were made of carved wood and were much lower than today’s chairs, chair seats were sometimes only 25 cm high..^[27] In ancient Egypt chairs appear to have been of great richness and splendor. Fashioned of ebony and ivory, or of carved and gilded wood, they were covered with costly materials, magnificent patterns and supported upon representations of the legs of beasts or the figures of captives.^[28] Generally speaking, the higher ranked an individual was, the taller and more sumptuous was the chair he sat on and the greater the honor. On state occasions the pharaoh sat on a throne, often with a little footstool in front of it.^[29]

The average Egyptian family seldom had chairs, and if they did, it was usually only the master of the household who sat on a chair. Among the better off, the chairs might be painted to look like the ornate inlaid and carved chairs of the rich, but the craftsmanship was usually poor.^[30]

During the Tang dynasty (618 - 907 AD), a higher seat first started to appear amongst the Chinese elite and their usage soon spread to all levels of society. By the 12th century seating on the floor was rare in China, unlike in other Asian countries where the custom continued, and the chair, or more commonly the stool, was used in the vast majority of houses throughout the country.^[31]

In Europe, it was owing in great measure to the Renaissance that the chair ceased to be a privilege of state, and became a standard item of furniture for anyone who could afford to buy it. Once the idea of privilege faded the chair speedily came into general use. We find almost at once that the chair began to change every few years to reflect the fashions of the day.^[32]

In the 1880s, chairs became more common in American households and usually there was a chair provided for every family member to sit down to dinner. By the 1830s, factory-manufactured “fancy chairs” like those by Sears. Roebuck, and o. allowed families to purchase machined sets. With the Industrial Revolution, chairs became much more available.^[33]

The 20th century saw an increasing use of technology in chair construction with such things as all-metal folding chairs, metal-legged chairs, the Slumber Chair,^[34] moulded plastic chairs^[35] and ergonomic chairs.^[36] The recliner became a popular form, at least in part due to radio and television.

The modern movement of the 1960s produced new forms of chairs: the butterfly chair (originally called the Hardoy chair),^[37] bean bags,^[38] and the egg-shaped pod chair.^[39] Technological advances led to molded plywood and wood laminate chairs, as well as chairs made of leather or polymers. Mechanical technology incorporated into the chair enabled adjustable chairs, especially for office use. Motors embedded in the chair resulted in massage chairs.^[40][41]

Materials

The design may be made of porous materials, or be drilled with holes for decoration; a low back or gaps can provide ventilation. The back may extend above the height of the occupant's head, which can optionally contain a headrest. Chairs can also be made from more creative materials, such as recycled materials like cutlery and wooden play bricks, pencils, plumbing tubes, rope and pvc pipe.^[42]

Raimonds Cirulis, a Lativan interior designer, created a Volcanic Hanging Chair that is a 100% handmade piece of furniture and is made out of volcanic rock.^[43] Peter Brenner, a Dutch-born German designer, has created a chair made from lollipop sugar, made from 60 pounds of confectioners' sugar.^[44]

Design and ergonomics

S Chair, Designed by Verner Panton

Chair design considers intended usage, ergonomics (how comfortable it is for the occupant),^[45] as well as non-ergonomic functional requirements such as size, stackability, foldability, weight, durability, stain resistance and artistic design. Intended usage determines the desired seating position. "Task chairs",^[46][47] or any chair intended for people to work at a desk or table, including dining chairs, can only recline very slightly; otherwise the occupant is too far away from the desk or table. Dental chairs are necessarily reclined. Easy chairs for watching television or movies are somewhere in between depending on the height of the screen.

Ergonomic design distributes the weight of the occupant to various parts of the body. A seat that is higher results in dangling feet and increased pressure on the underside of the knees ("popliteal fold"). It may also result in no weight on the feet which means more weight elsewhere. A lower seat may shift too much weight to the "seat bones" ("ischial tuberosities").

A reclining seat and back will shift weight to the occupant's back. This may be more comfortable for some in reducing weight on the seat area, but may be problematic for others who have bad backs. In general, if the occupant is supposed to sit for a long time, weight needs to be taken off the seat area and thus "easy" chairs intended for long periods of sitting are generally at least slightly reclined. However, reclining may not be suitable for chairs intended for work or eating at table.

The back of the chair will support some of the weight of the occupant, reducing the weight on other parts of the body. In general, backrests come in three heights: Lower back backrests support only the lumbar region. Shoulder height backrests support the entire back and shoulders. Headrests support the head as well and are important in vehicles for preventing "whiplash" neck injuries in rear-end collisions where the head is jerked back suddenly. Reclining chairs typically have at least shoulder height backrests to shift weight to the shoulders instead of just the lower back.

The Difference between Leg Room & Seat Pitch

Some chairs have foot rests. A stool or other simple chair may have a simple straight or curved bar near the bottom for the sitter to place his or her feet on.

Some chairs have two curved bands of wood (also known as rockers) attached to the bottom of the legs. They are called rocking chairs.

The type of chair popular in western Hubei, China: with a fairly low seat and the back inclined at about 45 degrees from the vertical

A kneeling chair adds an additional body part, the knees, to support the weight of the body. A sit-stand chair distributes most of the weight of the occupant to the feet. Many chairs are padded or have cushions. Padding can be on the seat of the chair only, on the seat and back, or also on any arm rests and/or foot rest the chair may have. Padding will not shift the weight to different parts of the body (unless the chair is so soft that the shape is altered). However, padding does distribute the weight by increasing the area of contact between the chair and the body. A hard wood chair feels hard because the contact point between the occupant and the chair is small. The same body weight over a smaller area means greater pressure on that area. Spreading the area reduces the pressure at any given point. In lieu of padding, flexible materials, such as wicker, may be used instead with similar effects of distributing the weight. Since most of the body weight is supported in the back of the seat, padding there should be firmer than the front of the seat which only has the weight of the legs to support. Chairs that have padding that is the same density front and back will feel soft in the back area and hard to the underside of the knees.

There may be cases where padding is not desirable. For example, in chairs that are intended primarily for outdoor use. Where padding is not desirable, contouring may be used instead. A contoured seat pan attempts to distribute weight without padding. By matching the shape of the occupant's buttocks, weight is distributed and maximum pressure is reduced.

Churchchairs

Actual chair dimensions are determined by measurements of the human body or anthropometric measurements. The two most relevant anthropometric measurement for chair design is the popliteal height and buttock popliteal length.

For someone seated, the popliteal height is the distance from the underside of the foot to the underside of the thigh at the knees. It is sometimes called the "stool height." The term "sitting height" is reserved for the height to the top of the head when seated. For American men, the median popliteal height is 16.3 inches (410 mm) and for American women it is 15.0 inches (380 mm) [1]. The popliteal height, after adjusting for heels, clothing and other issues is used to determine the height of the chair seat. Mass produced chairs are typically 17 inches (430 mm) high.

For someone seated, the buttock popliteal length is the horizontal distance from the back most part of the buttocks to the back of the lower leg. This anthropometric measurement is used to determine the seat depth. Mass produced chairs are typically 15-17 inches deep.

Additional anthropometric measurements may be relevant to designing a chair. Hip breadth is used for chair width and armrest width. Elbow rest height is used to determine the height of the armrests. The buttock-knee length is used to determine "leg room" between rows of chairs. "Seat pitch" is the distance between rows of seats. In some airplanes and stadiums the leg room (the seat pitch less the thickness of the seat at thigh level) is so small that it is sometimes insufficient for the average person.

For adjustable chairs, such as an office chair, the aforementioned principles are applied in adjusting the chair to the individual occupant.

Caster wheels are attached to the feet of chairs to give more mobility

Gas springs are attached to the body of the chair in order to give height adjustment and more comfort to the user

Armrests

Eames Lounge Chair and ottoman

Art deco club chair.

A chair may or may not have armrests; chairs with armrests are termed armchairs. In French, a distinction is made between fauteuil and chaise, the terms for chairs with and without armrests, respectively. If present, armrests will support part of the body weight through the arms if the arms are resting on the armrests. Armrests further have the function of making entry and exit from the chair easier (but from the side it becomes more difficult). Armrests should support the forearm and not the sensitive elbow area. Hence in some chair designs, the armrest is not continuous to the chair back, but is missing in the elbow area.

A couch, bench, or other arrangement of seats next to each other may have armrest at the sides and/or arm rests in between. The latter may be provided for comfort, but also for privacy e.g. in public transport and other public places, and to prevent lying on the bench. Arm rests reduce both desired and undesired proximity. A loveseat in particular, has no armrest in between.

See also seats in movie theaters, and pictures of benches with and without arm rests.

Chair seats

Polypropylene (molded plastic) seats and stainless steel legs in Rio de Janeiro, Brazil. This type of material is very useful in sea regions

Chair seats vary widely in construction and may or may not match construction of the chair's back (backrest).

Some systems include:

• center seats where a solid material forms the chair seat.
  • Solid wood, may or may not be shaped to human contours.
  • Wood slats, often seen on outdoor chairs
  • Padded leather, generally a flat wood base covered in padding and contained in soft leather
  • Stuffed fabric, similar to padded leather
  • Metal seats of solid or open design
  • Molded plastic
  • Stone, often marble
• Open center seats where a soft material is attached to the tops of chair legs or between stretchers to form the seat.
  • Wicker, woven to provide a surface with give to it
  • Leather, may be tooled with a design
  • Fabric, simple covering without support
  • Tape, wide fabric tape woven into seat, seen in lawn chairs and some old chairs
  • Caning, woven from rush, reed, rawhide, heavy paper, strong grasses, cattails to form the seat, often in elaborate patterns
  • Splint, ash, oak or hickory strips are woven
  • Metal, Metal mesh or wire woven to form seat

Standards and specifications

Highly decorated carved-back chairs in Mexico

Design considerations for chairs have been codified into standards. ISO 9241, "Ergonomic requirements for office work with visual display terminals (VDTs) -- Part 5: Workstation layout and postural requirements" is the most common one for modern chair design.

There are multiple specific standards for different types of chairs. Dental chairs are specified by ISO 6875. Bean bag chairs are specified by ANSI standard ASTM F1912-98 [2]. ISO 7174 specifies stability of rocking and tilting chairs. ASTM F1858-98 specifies plastic lawn chairs. ASTM E1822-02b defines the combustibility of chairs when they are stacked.

The Business and Institutional Furniture Manufacturer's Association (BIFMA)[3] defines BIFMA X5.1 for testing of commercial-grade chairs. It specifies things like [4]:

• chair back strength of 150 pounds (68 kg)
• chair stability if weight is transferred completely to the front or back legs
• leg strength of 75 pounds (34 kg) applied one inch (25 mm) from the bottom of the leg
• seat strength of 225 pounds (102 kg) dropped from six inches (150 mm) above the seat
• seat cycle strength of 100,000 repetitions of 125 pounds (57 kg) dropped from 2 inches (50 mm) above the seat

The specification further defines heavier "proof" loads that chairs must withstand. Under these higher loads, the chair may be damaged, but it must not fail catastrophically.

Large institutions that make bulk purchases will reference these standards within their own even more detailed criteria for purchase. [5] Governments will often issue standards for purchases by government agencies (e.g. Canada's Canadian General Standards Board CAN/CGSB 44.15M [6] on "Straight Stacking Chair, Steel" or CAN/CGSB 44.232-2002 on "Task Chairs for Office Work with Visual Display Terminal").

Chairs may be rated by the length of time that they may be used comfortably — an 8-hour chair, a 24-hour chair, and so on. Such chairs are specified for tasks which require extended periods of sitting, such as for receptionists or supervisors of a control panel.

Accessories

AISI 304 stainless steel laboratory chair with gas springs and caster wheels. A specific type of chair for professional use

In place of a built-in footrest, some chairs come with a matching ottoman. An ottoman is a short stool intended to be used as a footrest but can sometimes be used as a stool. If matched to a glider, the ottoman may be mounted on swing arms so that the ottoman rocks back and forth with the main glider.

A chair cover is a temporary fabric cover for a side chair. They are typically rented for formal events such as wedding receptions to increase the attractiveness of the chairs and decor. The chair covers may come with decorative chair ties, a ribbon to be tied as a bow behind the chair. Covers for sofas and couches are also available for homes with small children and pets. In the second half of 20th century, some people used custom clear plastic covers for expensive sofas and chairs to protect them.

Chair pads are cushions for chairs. They contain cotton or foam for padding. Some are decorative. In cars, they may be used to increase the height of the driver. Orthopedic backrests provide support for the back. Some manufacturers have patents on their designs and are recognized by medical associations as beneficial [7][8][9]. Car seats sometimes have built-in and adjustable lumbar supports. These can also be used on kitchen chairs.

Chair mats are mats meant to cover carpet or hardwood flooring. They are usually made from plastic. This allows chairs on wheels to roll easily over the carpet and/or protects the carpet or floor. They come in various shapes, some specifically sized to fit partially under a desk.

Remote control bags can be draped over the arm of easy chairs or sofas and used to hold remote controls. They are counter-weighted so as to not slide off the arms under the weight of the remote control.

Chair glides are attached to the feet of chairs to prevent them from scratching or snagging on the floor.

The Twelve Chairs monument in Odessa - Deribassovskaya street (Ukraine).

Chairs as sculptural and art forms

In 2001, Steve Mann exhibited a chair sculpture at San Francisco Art Institute. The chair had spikes that retracted when a credit card was inserted to download a seating license.

Chair sculpture by Steve Mann, exhibited at San Francisco Art Institute, 2001, comprises spikes that retract when a credit card is inserted to download a seating license.

Later other museums and galleries were equipped with the Pay to Sit chair, with a global central seating license server located in Toronto. Patrons anywhere in the world could each receive one free seat license. The first seating session was free, with a database of persons who'd already used their free session.

In language

• A film or a story is said to keep you on the edge of your seat, if it is suspenseful or engaging.
• If you nearly fell off your chair, it was because you were very surprised.
• An orchestra awards a musician a chair or seat based on ability. The best player in a particular section will receive "first chair," or the "principal seat." It is also common for this position to be known as 'first stand,' a reference to the portable lectern on which the musicians put their sheet music. However, the person who is first chair in the first violin section is usually referred to as the concertmaster in the USA or leader in the UK.
• Musical chairs is a common party game, and a colloquial expression to describe people shuffling from seat to seat, or around different locations.
• In American slang, to say someone has gotten "the chair" is to say that they have been executed by an electric chair.
• To be on its last leg is an expression that stems from the practice of sawing the ends of chair legs off in previous centuries. It means that it is decrepit and nearing the end of its serviceability.

See also

Look up chair in Wiktionary, the free dictionary.

Wikimedia Commons has media related to: Chairs

See List of chairs for an extended list of chair types, such as the bean bag chair, lift chair, papasan chair, sofa, swivel chair and throne.

• Couch
• Cushion
• History of the chair
• Riding-like sitting
• Sitting
• Seating
• Splat, the central vertical element of a wooden chair back

References

• "Guide to Great Chair Design." Guide to Great Chair Design. N.p., n.d. Web. 9 May 2011. <http://greatchairdesign.com/>
• "folding chairs through the ages." designboom. N.p., n.d. Web. 9 May 2011. <http://www.designboom.com/eng/education/foldingchair.html>.
• "chair history — Chair Blog." Chair Blog — Chairs, Chair Designers and Chair Manufacturers. N.p., n.d. Web. 9 May 2011. <http://www.chairblog.eu/category/chair-history/>.

Further reading

de Dampierre, F. (2006). Chairs: A History. Harry N. Abrams. ISBN 0-8109-5484-2

Fiell, C. (2005). 1000 Chairs. (25th ed.). Taschen. ISBN 3-8228-4103-X

Miller, J. (2009). Chairs. Conran. ISBN 1-84091-523-4