countertop

A stainless steel countertop

Countertop (also counter top, countertopping, benchtop, or (British English) worktop) usually refers to a horizontal worksurface in kitchens, other food preparation areas, and workrooms in general. It is frequently installed above and supported by cabinets.

Kitchen countertops

When installed in a kitchen, countertops are usually about 25 1/2 inches (650 mm) from front to back and are designed to slightly-overhang standard kitchen base cabinets. This allows a convenient reach to objects at the back of the countertop. They often contain some sort of integrated backsplash to prevent spilled liquids from falling behind the cabinets and the face of the countertop may be decorated in ways ranging from plain to very elaborate. They may be cut away to accommodate the installation of sinks, stoves (cookers), ranges, and cooktops, or other accessories such as integrated drain boards and cutting boards.

Materials

Countertops can be made from a very wide range of materials and the cost of the completed countertop can vary very widely depending on the material chosen. The durability and ease of use of the material often rises with the increasing cost of the material but this is not necessarily so; some very expensive materials are neither particularly durable nor easy to use, just stylish. Some common materials are as follows:

• Natural stones:
  • Granite
  • Limestone
  • Marble
  • Soapstone
  • Gabbro
• Wood
• Stainless steel
• Crafted glass
• Synthetic materials:
  • Concrete
  • Pre- and postformed high-pressure decorative laminates such as Wilsonart Laminate, Pionite Laminate, Formica (plastic) and Arborite
  • Quartz Surfacing or Engineered Stone is 99.9% solid @ 93% aggregate / 7% polyester resin, colors and binders
  • Richlite
  • Solid-surface acrylic plastic materials such as Corian, Meganite, Avonite, Wilsonart Solid Surface, The Onyx Collection
  • Solid-surface Polyester acrylic
  • Terrazzo
  • Tile
  • Cast-in-place materials (resin plus natural stone)
  • Epoxy
  • Phenolic resin

Natural stone

The natural stone or dimension stone slab (e.g. granite) is shaped using cutting and finishing equipment in the shop of the fabricator. The edges are commonly put on by hand-held routers, grinders, or CNC equipment. If the stone has a highly varigated pattern, the stone is laid out in final position in the shop for the customer's inspection. Then the countertop assembly is installed on the job site by professionals.

Wood

Wooden Countertops can come in a variety of designs ranging from Butcher's Block to Joined Planks to Single Wide Stave. Wood is considered to be the most eco-friendly option when it comes to choosing a kitchen countertop as wood is a renewable resource. Wood countertops must be thoroughly cleaned and disinfected after contact with foods such as raw meat. Although the use of wooden work surfaces is prohibited in commercial food production areas in the EU and the US Department of Agriculture advises against the use of wooden chopping boards, research by the Food Research Institute at the University of Wisconsin has shown that wooden work surfaces are no more dangerous, and in some cases safer than plastic alternatives. They have shown that whilst that bacteria does get absorbed by the wood it does not multiply and eventually dies. Whilst brand new plastic work surfaces are indeed easy to disinfect, once they have become heavily knife scarred they are nearly impossible to completely disinfect. This is not a problem with wooden work surfaces where the number of knife cuts made little difference.^[1]

Post-formed plastic laminate

The most economical style is the "postformed" (or literally "formed after being laminated" to the substrate) high pressure laminate countertop, often referred to as "plastic laminate countertop", however, the surface material is more of a wood product, consisting of kraft and decorative papers, and resins, bonded through high heat and pressure. We often refer to the product as "Formica", but that is a trade name of a manufactured high pressure laminate.

The postform countertop is typically a high volume factory-produced product, which accounts for the economy of the product. The material composition consists of a single thin sheet of laminate (typically .030" - .040" in thickness) that gets bonded to a 45# density particle board substrate (or other similar base material such as MDF - medium density fiberboard, or plywood), with a PVA adhesive (poly vinyl acetate - a water-based adhesive).

A typical system consists of the following:

1) An automated infeed system for sequencing the particle board into production. 2) The CorFab Machine, an automated feed-through machine that cuts to size, cuts and bonds build down sticks with a hot melt adhesive to the under side of the substrate, and shapes the edge detail, all in a single motion. 3) An automated laminating system that applies the adhesive to both the substrate and laminate. 4) An indexing unit that aligns the laminate to the substrate with the proper overhang. 5) A Pinch Roller that makes the bond between the laminate and substrate. 6) The Postforming Machine, that not only heats and forms the laminate around the substrate, but also cuts away the backsplash from the main deck, all in a feed-through motion machine. 7) The AutoCove Machine, which heats and forms the backsplash upward 90 degrees, locking it into place with what is referred to as a cove stick, utilizing hot melt adhesive technology to hold it all together. 8) The final stage of the system usually consists of a trim saw that cuts the countertops to rough lengths, typically 8', 10' and 12', ready for distribution.

Once manufactured and in the hands of a professional installer (Top Shop), the tops need only to be cut to length, mitered, fitted for assembly, and end capped (only if it is a visible finished end). A very specific machine for cutting the postform countertop is manufactured by only a few companies, it is commonly called a Cutting Station, Top Saw, or simply Miter Saw. This machine accurately cuts the countertop to field dimensions, making it easy for the installer to make the final scribe cuts on-site to complete the work. Sink cut outs can be made either in the field or at the installers shop.

A proper installation of a postform countertop will leave the home owner with a contemporary design element in their home, provide durability at a low cost, and allow for easy to no maintenance of their decorative surfaces for years to come. It is not only a wise choice for value, it is a smart choice for both function and esthetic.

Self edge or wood edge laminate

Self or wood edge plastic laminate countertops are also very popular for those who chose to have few or no surface seams. In this style, the top shop uses substrate for the countertop out of MDF, or particle board and then glue sheets of laminate to the substrate using Contact Cement. The laminate is then trimmed using a router. This method can't reproduce the curved contours of post-formed countertopping but can be made to easily conform to a much-wider range of floor plans with fewer seams.

Crafted glass

Custom architectural crafted glass, tempered glass, textured glass pieces, and the ancient art of Verre églomisé, or reverse gilded glass, are applied to contemporary uses including countertops, backsplashes, and tabletops. Glass work may be customized to suit by craftsmen in the studio, then installed on site either in small components (such as a kitchen countertop composed of three rectangles of verre églomisé) or as immense, single units (for example, a glass countertop and sink basin formed of one continuous piece of textured glass). The glass is non-porous, relatively stain-proof, extremely hygienic, and "extremely heat resistant (up to 700 degrees)."^[2] Much work is being done to "recycle" glass using sources such as post consumer glass or post industrial float glass. The material can be crushed or cut into strips that is heated until the softening point of glass, binding the loose material back into a solid form.

Ribbons of colored glass fused into a solid slab

Tile

Tile, including ceramic tile and stone tile, is installed in much the same way as flat lay laminate except that the gaps between the tiles are grouted after the tile has been glued down.

Solid-surface plastic materials

Solid-surface plastic acrylic or polyester materials are usually prefabricated at the installer's shop and then assembled on site. The plastic material is readily glued and the glue joints are then sanded, leaving almost no visible trace of the joint. The edge treatment for solid-surface countertops can be very elaborate. The material itself is usually only about 12 mm (1/2 inch) thick so an edge is usually created by stacking up two or three layers of the material. The built-up edge then can be shaped to a rounded edge or an ogee. Fancier edge treatments are, of course, more expensive.

Natural quartz surfacing

Natural quartz surfacing is made from 100% natural quartz cut from blocks into slabs. The slabs are custom cut to create countertops. Quartz is naturally non-porous and scratch resistant. As with solid surface countertopping, the materials are prefabricated and installed by professionals. Thicknesses may be 1.2 cm (1/2 inch), 2 cm (3/4 inch), 3 cm (1 1/4 inch) or 4 cm (1 1/2 inch).

Engineered quartz surfacing

Engineered quartz surfacing is made from approximately 95% natural quartz and 5% polymer resins. Testing has shown that they retain much of the toughness of quartz but display increased ductility due to the resin, improving impact resistance^[3]. Countertops are custom made and are more scratch resistant as well as less porous than natural quartz surfaces. Thicknesses may be 6mm, 1.2 cm (1/2 inch), 2 cm (3/4 inch), 3 cm (1 1/4 inch) or 4 cm (1 1/2 inch). Brands include Hanstone,NaturaStone, Silestone, Q, Caesarstone,Technistone, Cambria, and Zodiaq.^[4]

Other materials

Stainless steel, stone, concrete, terrazzo, and other materials are usually prefabricated and assembled on site as well. The difficulty of prefabrication rises with the more exotic materials. As with solid-surface plastic materials, the edge treatments can vary widely, but the material is usually thicker than with plastic so there is often no need to build up the edge with multiple layers of the material.

Many predesigned, prefabricated units (including sinks, drainboards, and other accessories) are available in stainless steel. These may be used "stand-alone" or integrated into larger custom assemblies. Some stainless steel systems stand on their own legs and do not require the support of cabinetry.

Sink installation

In any of these styles, "self-rimming" sinks can be used. These sit in appropriately-shaped holes cut in the countertop (or substrate material) using a jigsaw or other cutter appropriate to the material at hand and are suspended by their rim. The rim then inherently forms a fairly close seal with the top surface of the countertop, especially when the sink is clamped into the hole from below.

The materials also allow the installation of a "bottom-mount" or "under-mount" sink. With these, the edge of the countertop material is exposed at the hole created for the sink (and so must be a carefully finished edge rather than a rough cut; this cut is generally done at the fabricator's workshop). The sink is then mounted to the bottom of the material from below. Especially for under-mount sinks, silicone-based sealants are usually used to assure a waterproof joint between the sink and the countertop material. The advantage of an "under-mount" sink is that it gives a contemporary look to the kitchen but the disadvantages are extra cost in both the sink and the counter top.

Solid-surface plastic materials allow a third option: sinks made of the same plastic material as the countertop can easily be glued to the underside of the countertop material and the joint sanded flat, creating the usual invisible joint and completely eliminating any dirt-catching seam between the sink and the countertop. The disadvantage is that the sinks do not have the same impact resistance of stainless or cast iron and may differentially expand and contract with extreme temperature change (as might be caused by a pot of hot water dumped into the sink). In a similar fashion, with stainless steel, a sink may be welded into the countertop; the joint is then ground to create a finished, concealed appearance.

References

1. ^ "Research indicates that wood is a safer material in contact with foodstuffs than currently recommended alternatives.", Dean O. Cliver, Ph.D., 1994
2. ^ "Kitchen Cabinets: What's Hot Right Now". The Sexy Kitchen. http://www.thesexykitchen.com/kitchen_countertops_intro.html. Retrieved 2008-02-19. 
3. ^ "The Qualities of Quartz Surfacing", Ed Rogers, CSI and Brenda Little, CSI, JD, LEED AP, The Construction Specifier, February 2009
4. ^ "Quartz Countertops: Why Quartz is Gaining Popularity". Scott Jenkins. http://www.quartz-countertop.info. Retrieved 2008-06-08. 

External links

• Video on countertop styles
• International Surface Fabricators Association, a nonprofit trade organization