Diesel cycle: Definition from Answers.com

The Diesel cycle is the thermodynamic cycle which approximates the pressure and volume of the combustion chamber of the Diesel engine, invented by Rudolph Diesel in 1897. It is assumed to have constant pressure during the first part of the "combustion" phase , v2 to v3 in the diagram . This is mostly a mathematical model: real physical diesels do have an increase in pressure during this period, but it is less pronounced than in the Otto cycle. The idealized Otto cycle of a gasoline engine approximates constant volume during that phase, generating more of a spike in a p/v diagram.

1 The Idealized Diesel Cycle
- 1.1 Maximum thermal efficiency
2 General information
3 Other internal combustion engines without spark plugs
4 References
5 See also

The Idealized Diesel Cycle

P-v Diagram for the Ideal Diesel cycle. The cycle follows the numbers 1-4 in clockwise direction.

The image on the left shows a P-v diagram for the ideal diesel cycle; where P is pressure and v is specific volume. The ideal diesel cycle follows the following four distinct processes (The color references refer to the color of the line on the diagram.):

Process 1 to 2 is isentropic compression (blue)
Process 2 to 3 is reversible constant pressure heating (red)
Process 3 to 4 is isentropic expansion (yellow)
Process 4 to 1 is reversible constant volume cooling (green)^[1]

The diesel is a heat engine: it converts heat into work.

Work in (W_in) is done by the piston compressing the working fluid
Heat in (Q_in) is done by the combustion of the fuel
Work out (W_out) is done by the working fluid expanding on to the piston, this produces usable torque
Heat out (Q_out) is done by venting the air

Maximum thermal efficiency

The maximum thermal efficiency of a diesel cycle is dependent on the compression ratio and the cut-off ratio. It has the following formula:

$\eta_{th}=1-\frac{1}{r^{\gamma-1}}\left ( \frac{\alpha^{\gamma}-1}{\gamma(\alpha-1)} \right )$

Where

η t h

is thermal efficiency

α

is the cut-off ratio $\frac{V_3}{V_2}$ (ratio between the end and start volume for the combustion phase)

r is the compression ratio $\frac{V_1}{V_2}$

γ

is ratio of specific heats (C_p/C_v)^[2]

The cut-off ratio can be expressed in terms of temperature as shown below:

$\frac{T_2}{T_1} ={\left(\frac{V_1}{V_2}\right)^{\gamma-1}} = r^{\gamma-1}$

$\displaystyle {T_2} ={T_1} r^{\gamma-1}$

$\frac{V_3}{V_2} = \frac{T_3}{T_2}$

$\alpha = \left(\frac{T_3}{T_1}\right)\left(\frac{1}{r^{\gamma-1}}\right)$

$T 3$ can be approximated to the flame temperature of the fuel used. The flame temperature can be approximated to the adiabatic flame temperature of the fuel with corresponding air-to-fuel ratio and compression pressure, $P 3$ . $T 1$ can be approximated to the inlet air temperature.

This formula only gives the ideal thermal efficiency. The actual thermal efficiency will be significantly lower due to heat and friction losses. The formula is more complex than the Otto cycle (petrol/gasoline engine) relation that has the following formula;

$\eta_{otto,th}=1-\frac{1}{r^{\gamma-1}}$

The additional complexity for the diesel formula comes around since the heat addition is at constant pressure and the heat rejection is at constant volume. The Otto cycle by comparison has both the heat addition and rejection at constant volume.

Comparing the two formulae it can be seen that for a given compression ratio (r), the ideal Otto cycle will be more efficient. However, a diesel engine will be more efficient overall since it will have the ability to operate at higher compression ratios. If a petrol engine were to have the same compression ratio, then knocking (self-ignition) would occur and this would severely reduce the efficiency, whereas in a diesel engine, the self ignition is the desired behavior. Additionally, both of these cycles are only idealizations, and the actual behavior does not divide as clearly or sharply. And the ideal Otto cycle formula stated above does not include throttling losses, which do not apply to diesel engines.

The Diesel cycle is a combustion process of a reciprocating internal combustion engine. In it, fuel is ignited by heat generated by compressing air in the combustion chamber, into which fuel is injected. This is in contrast to igniting it with a spark plug as in the Otto cycle (four-stroke/petrol) engine. Diesel engines (heat engines using the Diesel cycle) are used in automobiles, power generation, diesel-electric locomotives, and submarines.

General information

Main article: Diesel engine

It should be noted that theoretical simplified approaches are common in engineering due to the complexity of real physical processes, and does not detract the value to realize more optimum solutions.

The diesel engine has the lowest specific fuel consumption of any large internal combustion engine, 0.26 lb/hp.h (0.16 kg/kWh) for very large marine engines. In fact, two-stroke diesels with high pressure forced induction, particularly turbocharging, make up a large percentage of the very largest diesel engines.

In North America, diesel engines are primarily used in large trucks, where the low-stress, high-efficiency cycle leads to much longer engine life and lower operational costs. These advantages also make the diesel engine ideal for use in the heavy-haul railroad environment.

Other internal combustion engines without spark plugs

Many model airplanes use very simple "glow" and "diesel" engines. Glow engines use glow plugs. "Diesel" model airplane engines have variable compression ratios. Both types depend on special fuels (easily obtainable in such limited quantities) for their ignition timing.

Some 19th century or earlier experimental engines used external flames, exposed by valves, for ignition, but this becomes less attractive with increasing compression. (It was the research of Nicolas Léonard Sadi Carnot that established the thermodynamic value of compression.) A historical implication of this is that the diesel engine would eventually have been invented without the aid of electricity.
See the development of the hot bulb engine and indirect injection for historical significance.

References

^ Eastop & McConkey 1993, Applied Thermodynamics for Engineering Technologists, Pearson Education Limited, Fifth Edition, p.137
^ The Diesel Engine

	mixed cycle (mechanical engineering)
	engine cycle (thermodynamics)
	Brayton cycle (thermodynamics)

	What is the timing belt setting for a 2001 dodge 5.9 24 valve 6 cycle diesel? Read answer...
	What is a cycle? Read answer...
	Why diesel engines run with diesel? Read answer...

	What are limitations of diesel cycle?
	Otto cycle and Diesel cycle with p-v diagram?
	What are the differences between otto cycle and diesel cycle?

		Sci-Tech Dictionary. McGraw-Hill Dictionary of Scientific and Technical Terms. Copyright © 2003, 1994, 1989, 1984, 1978, 1976, 1974 by McGraw-Hill Companies, Inc. All rights reserved. Read more
		Sci-Tech Encyclopedia. McGraw-Hill Encyclopedia of Science and Technology. Copyright © 2005 by The McGraw-Hill Companies, Inc. All rights reserved. Read more
		Wikipedia. This article is licensed under the Creative Commons Attribution/Share-Alike License. It uses material from the Wikipedia article "Diesel cycle". Read more

Diesel cycle

Contents

The Idealized Diesel Cycle

Maximum thermal efficiency

General information

Other internal combustion engines without spark plugs

References

See also