Failure rate: Definition from Answers.com

Failure rate is the frequency with which an engineered system or component fails, expressed for example in failures per hour. It is often denoted by the Greek letter λ (lambda) and is important in reliability engineering.

The failure rate of a system usually depends on time, with the rate varying over the life cycle of the system. For example, as an automobile grows older, the failure rate in its fifth year of service may be many times greater than its failure rate during its first year of service. One does not expect to replace an exhaust pipe, overhaul the brakes, or have major transmission problems in a new vehicle.

In practice, the Mean Time Between Failures (MTBF) is often used instead of the failure rate. The MTBF is an important system parameter in systems where failure rate needs to be managed, in particular for safety systems. The MTBF appears frequently in the engineering design requirements, and governs frequency of required system maintenance and inspections. In special processes called renewal processes, where the time to recover from failure can be neglected and the likelihood of failure remains constant with respect to time, the failure rate is simply the multiplicative inverse of the MTBF (1/λ).

A similar ratio used in the transport industries, especially in railways and trucking is 'Mean Distance Between Failure', a variation which attempts to correlate actual loaded distances to similar reliability needs and practices.

Failure rates and their projective manifestations are important factors in insurance, business, and regulation practices as well as fundamental to design of safe systems throughout a national or international economy.

1 Failure rate in the discrete sense
2 Failure rate in the continuous sense
3 Failure rate data
4 See also
5 References
- 5.1 Print
- 5.2 Online
6 External links

Failure rate in the discrete sense

In words appearing in an experiment, the failure rate can be defined as

The total number of failures within an item population, divided by the total time expended by that population, during a particular measurement interval under stated conditions. (MacDiarmid, et al.)

While failure rate $λ(t)$ is often thought of as the probability that a failure occurs in a specified interval, given no failure before time $t$ , it is not actually a probability because it can exceed 1. It can be defined with the aid of the reliability function or survival function $R (t)$ , the probability of no failure before time $t$ , as:

$\lambda = \frac{R(t_1)-R(t_2)}{(t_2-t_1) \cdot R(t_1)} = \frac{R(t)-R(t+\triangle t)}{\triangle t \cdot R(t)} \!$

where $t 1$ (or $t$ ) and $t 2$ are respectively the beginning and ending of a specified interval of time spanning $Δ t$ . Note that this is a conditional probability, hence the $R (t)$ in the denominator.

Failure rate in the continuous sense

Exponential failure density functions

By calculating the failure rate for smaller and smaller intervals of time $\scriptstyle\Delta t$ , the interval becomes infinitely small. This results in the hazard function, which is the instantaneous failure rate at any point in time:

$h(t)=\lim_{\triangle t \to 0} \frac{R(t)-R(t+\triangle t)}{\triangle t \cdot R(t)}.$

Continuous failure rate depends on a failure distribution, $\scriptstyle F(t)$ , which is a cumulative distribution function that describes the probability of failure prior to time t,

$P(\mathbf{T}\le t)=F(t)=1-R(t),\quad t\ge 0. \!$

where $T$ is the failure time. The failure distribution function is the integral of the failure density function, f(x),

$F(t)=\int_{0}^{t} f(x)\, dx. \!$

The hazard function can be defined now as

$h(t)=\frac{f(t)}{R(t)}. \!$

Many probability distributions can be used to model the failure distribution (see List of important probability distributions). A common model is the exponential failure distribution,

$F(t)=\int_{0}^{t} \lambda e^{-\lambda x}\, dx = 1 - e^{-\lambda t}, \!$

which is based on the exponential density function.

$h(t) = \frac{f(t)}{R(t)} = \frac{\lambda e^{-\lambda t}}{e^{-\lambda t}} = \lambda$

For an exponential failure distribution the hazard rate is a constant with respect to time (that is, the distribution is "memoryless"). For other distributions, such as a Weibull distribution or a log-normal distribution, the hazard function may not be constant with respect to time. For some such as the deterministic distribution it is monotonic increasing (analogous to "wearing out"), for others such as the Pareto distribution it is monotonic decreasing (analogous to "burning in"), while for many it is not monotonic.

Failure rate data

Failure rate data can be obtained in several ways. The most common means are:

Historical data about the device or system under consideration.

Many organizations maintain internal databases of failure information on the devices or systems that they produce, which can be used to calculate failure rates for those devices or systems. For new devices or systems, the historical data for similar devices or systems can serve as a useful estimate.

Government and commercial failure rate data.

Handbooks of failure rate data for various components are available from government and commercial sources. MIL-HDBK-217F, Reliability Prediction of Electronic Equipment, is a military standard that provides failure rate data for many military electronic components. Several failure rate data sources are available commercially that focus on commercial components, including some non-electronic components.

Testing.

The most accurate source of data is to test samples of the actual devices or systems in order to generate failure data. This is often prohibitively expensive or impractical, so that the previous data sources are often used instead.

Units

Failure rates can be expressed using any measure of time, but hours is the most common unit in practice. Other units, such as miles, revolutions, etc., can also be used in place of "time" units.

Failure rates are often expressed in engineering notation as failures per million, or 10^-6, especially for individual components, since their failure rates are often very low.

The Failures In Time (FIT) rate of a device is the number of failures that can be expected in one billion (10⁹) device-hours of operation. (E.g. 1000 devices for 1 million hours, or 1 million devices for 1000 hours each, or some other combination.) This term is used particularly by the semiconductor industry.

Additivity

Under certain engineering assumptions (e.g. besides the above assumptions for a constant failure rate, the assumption that the considered system has no relevant redundancies), the failure rate for a complex system is simply the sum of the individual failure rates of its components, as long as the units are consistent, e.g. failures per million hours. This permits testing of individual components or subsystems, whose failure rates are then added to obtain the total system failure rate.

Example

Suppose it is desired to estimate the failure rate of a certain component. A test can be performed to estimate its failure rate. Ten identical components are each tested until they either fail or reach 1000 hours, at which time the test is terminated for that component. (The level of statistical confidence is not considered in this example.) The results are as follows:

**Failure Rate Calculation Example**
Component	Hours	Failure
Component 1	1000	No failure
Component 2	1000	No failure
Component 3	467	Failed
Component 4	1000	No failure
Component 5	630	Failed
Component 6	590	Failed
Component 7	1000	No failure
Component 8	285	Failed
Component 9	648	Failed
Component 10	882	Failed
Totals	7502	6

Estimated failure rate is

$\frac{6\text{ failures}}{7502\text{ hours}} = 0.0007998 \frac\text{failures}\text{hour} = 799.8 \times 10^{-6} \frac\text{failures}\text{hour},$

or 799.8 failures for every million hours of operation.

References

Print

Blanchard, Benjamin S. (1992), Logistics Engineering and Management, Fourth Ed., pp 26-32, Prentice-Hall, Inc., Englewood Cliffs, New Jersey.
Ebeling, Charles E., (1997), An Introduction to Reliability and Maintainability Engineering, pp 23-32, McGraw-Hill Companies, Inc., Boston.
Federal Standard 1037C
Kapur, K.C., and Lamberson, L.R., (1977), Reliability in Engineering Design, pp 8-30, John Wiley & Sons, New York.
Knowles, D.I.,(1995), Should We Move Away From "Acceptable Failure Rate", Communications in Reliability Maintainability and Supportability, Vol. 2, No. 1, P. 23, International RMS Committee, USA
MacDiarmid, Preston; Morris, Seymour; et al., (no date), Reliability Toolkit: Commercial Practices Edition, pp 35-39, Reliability Analysis Center and Rome Laboratory, Rome, New York.
Rausand, M. and Hoyland, A., (2004), System Reliability Theory; Models, Statistical methods, and Applications, John Wuiley & Sons, New York. web site
Turner, T., Hockley, C., and Burdaky, R., (1997), The Customer Needs A Maintenance-Free Operating Period, 1997 Avionics Conference and Exhibition, No. 97-0819, P. 2.2, ERA Technology Ltd., Leatherhead, Surrey, UK

Online

External links

Statistics

Descriptive statistics

Continuous data

Location	Mean (Arithmetic, Geometric, Harmonic) · Median · Mode

Dispersion	Range · Standard deviation · Coefficient of variation · Percentile

Moments	Variance · Semivariance · Skewness · Kurtosis

Categorical data

Frequency · Contingency table

Inferential statistics
and
hypothesis testing

Inference	Confidence interval (Frequentist inference) · Credible interval (Bayesian inference) · Significance · Meta-analysis

Design of experiments	Population · Sampling · Stratified sampling · Replication · Blocking · Sensitivity and specificity

Sample size estimation	Statistical power · Effect size · Standard error

General estimation	Bayesian estimator · Maximum likelihood · Method of moments · Minimum distance · Maximum spacing

Specific tests	Z-test (normal) · Student's t-test · F-test · Chi-square test · Pearson's chi-square test · Wald test · Mann–Whitney U · Wilcoxon signed-rank test

Survival analysis	Survival function · Kaplan–Meier · Logrank test · Failure rate · Proportional hazards models

Correlation
and
Regression analysis

Correlation	Pearson product-moment correlation · Rank correlation (Spearman's rho, Kendall's tau) · Confounding variable

Linear regression	Linear model · General linear model · Generalized linear model · Analysis of variance · Analysis of covariance

Nonlinear regression	Nonparametric · Semiparametric · Logistic

Statistical graphics

Bar chart · Biplot · Box plot · Control chart · Correlogram · Forest plot · Histogram · Q-Q plot · Run chart · Scatter plot · Stemplot

Category · Portal · Outline · Index

This entry is from Wikipedia, the leading user-contributed encyclopedia. It may not have been reviewed by professional editors (see full disclaimer)

Donate to Wikimedia

	bathtub curve (industrial engineering)
	confidence (statistics)
	Failure Mode and Effect Analysis (insurance term)

	Define failure rate in reliability? Read answer...
	What is the failure rate of levora? Read answer...
	What is the failure rate for dieting in the US? Read answer...

	What is the failure rate of tubal ligation?
	What is the failure rate of a new business?
	What is the rate of business failure?

		Sci-Tech Dictionary. McGraw-Hill Dictionary of Scientific and Technical Terms. Copyright © 2003, 1994, 1989, 1984, 1978, 1976, 1974 by McGraw-Hill Companies, Inc. All rights reserved. Read more
		Wikipedia. This article is licensed under the Creative Commons Attribution/Share-Alike License. It uses material from the Wikipedia article "Failure rate". Read more

Failure rate

Contents