Ignition system

This article needs additional citations for verification. Please help improve this article by adding reliable references. Unsourced material may be challenged and removed. (September 2007)

This article uses bare URLs. Please help improve this article by turning bare URLs into proper citations containing all of the information on the referenced work's title, date, publisher, publication, and author, so that the article remains verifiable in the future. (There are several templates available that can help to make formatting such citations simple.) This page may also be able to help find problematic links. (May 2009)

An ignition system is a system for igniting a fuel-air mixture. It is best known in the field of internal combustion engines but also has other applications, e.g. in oil-fired and gas-fired boilers. The earliest internal combustion engines used a flame, or a heated tube, for ignition but these were quickly replaced by systems using an electric spark.

Contents 1 History 1.1 Magneto systems 1.2 Switchable systems 1.3 Battery-operated ignition 2 Modern ignition systems 2.1 Mechanically timed ignition 2.2 Electronic ignition 2.3 Digital Electronic Ignitions 3 Engine management 4 Turbine and jet engines 5 See also 6 References

History

Magneto systems

The simplest form of spark ignition is that using a magnet. The engine spins a magnet inside a coil, or, in the earlier designs, a coil inside a fixed magnet, and also operates a contact breaker, interrupting the current and causing the voltage to be increased sufficiently to jump a small gap. The spark plugs are connected directly from the magneto output. Early magnetos had one coil, with the contact breaker (sparking plug) inside the combustion chamber. In about 1902, Bosch introduced a double-coil magneto, with a fixed sparking plug, and the contact breaker outside the cylinder. Magnetos are not used in modern cars, but because they generate their own electricity they are often found on piston aircraft engines and small engines such as those found in mopeds, lawnmowers, snowblowers, chainsaws, etc. where a battery-based electrical system is not present for any combination of necessity, weight, cost, and reliability reasons.

Magnetos were used on the small engine's ancestor, the stationary "hit or miss" engine which was used in the early twentieth century, on older gasoline or distillate farm tractors before battery starting and lighting became common, and on aircraft piston engines. Magnetos were used in these engines because their simplicity and self-contained operation was more reliable, and because magnetos weighed less than having a battery and generator or alternator.

Aircraft engines usually have multiple magnetos to provide redundancy in the event of a failure. Some older automobiles had both a magneto system and a battery actuated system (see below) running simultaneously to ensure proper ignition under all conditions with the limited performance each system provided at the time.This gave the benefits of easy starting (from the battery system) with reliable sparking at speed (from the magneto).

Switchable systems

The output of a magneto depends on the speed of the engine, and therefore starting can be problematic. Some magnetos include an impulse system, which spins the magnet quickly at the proper moment, making easier starting at slow cranking speeds. Some engines, such as aircraft but also the Ford Model T, used a system which relied on non rechargeable dry cells, (similar to a large flashlight battery, and which was not maintained by an electrical system as on modern automobiles) to start the engine or for starting and running at low speed. The operator would manually switch the ignition over to magneto operation for high speed operation.

In order to provide high voltage for the spark from the low voltage batteries, a "tickler" was used, which was essentially a larger version of the once widespread electric buzzer. With this apparatus, the direct current passes through an electromagnetic coil which pulls open a pair of contact points, interrupting the current; the magnetic field collapses, the spring-loaded points close again, the circuit is reestablished, and the cycle repeats rapidly. The rapidly collapsing magnetic field, however, induces a high voltage across the coil which can only relieve itself by arcing across the contact points; while in the case of the buzzer this is a problem as it causes the points to oxidize and/or weld together, in the case of the ignition system this becomes the source of the high voltage to operate the spark plugs.

In this mode of operation, the coil would "buzz" continuously, producing a constant train of sparks. The entire apparatus was known as the Model T spark coil (in contrast to the modern ignition coil which is only the actual coil component of the system), and long after the demise of the Model T as transportation they remained a popular self-contained source of high voltage for electrical home experimenters, appearing in articles in magazines such as Popular Mechanics and projects for school science fairs as late as the early 1960s. In the UK these devices were commonly known as trembler coils and were popular in cars pre-1910, and also in commercial vehicles with large engines until around 1925 to ease starting.

The Model T (built into the flywheel) differed from modern implementations by not providing high voltage directly at the output; the maximum voltage produced was about 30 volts, and therefore also had to be run through the spark coil to provide high enough voltage for ignition, as described above, although the coil would not "buzz" continuously in this case, only going through one cycle per spark. In either case, the high voltage was switched to the appropriate spark plug by the timer mounted on the front of the engine, the equivalent of the modern distributor. The timing of the spark was adjustable by rotating this mechanism through a lever mounted on the steering column.

Battery-operated ignition

With the universal adaptation of electrical starting for automobiles, and the concomitant availability of a large battery to provide a constant source of electricity, magneto systems were abandoned for systems which interrupted current at battery voltage, used an ignition coil (a type of autotransformer) to step the voltage up to the needs of the ignition, and a distributor to route the ensuing pulse to the correct spark plug at the correct time.

The first reliable battery operated ignition was developed by the Dayton Engineering Laboratories Co. (Delco) and introduced in the 1910 Cadillac. This ignition was developed by Charles Kettering and was a wonder in its day. It consisted of a single coil, points (the switch), a capacitor and a distributor set up to allocate the spark from the ignition coil timed to the correct cylinder. The coil was basically an autotransformer set up to step up the low (6 or 12V) voltage supply to the high ignition voltage required to jump a spark plug gap.

The points allow the coil to charge magnetically and then, when they are opened by a cam arrangement, the magnetic field collapses and a large (20KV or greater) voltage is produced. The capacitor is used to absorb the back EMF from the magnetic field in the coil to minimize point contact burning and maximize point life. The Kettering system became the primary ignition system for many years in the automotive industry due to its lower cost, higher reliability and relative simplicity.[1].

Modern ignition systems

Mechanically timed ignition

Most four-stroke engines have used a mechanically timed electrical ignition system. The heart of the system is the distributor. The distributor contains a rotating cam driven by the engine's drive, a set of breaker points, a condenser, a rotor and a distributor cap. External to the distributor is the ignition coil, the spark plugs and wires linking the distributor to the spark plugs and ignition coil.

The system is powered by a lead-acid battery, which is charged by the car's electrical system using a dynamo or alternator. The engine operates contact breaker points, which interrupt the current to an induction coil (known as the ignition coil).

The ignition coil consists of two transformer windings sharing a common magnetic core—the primary and secondary windings. An alternating current in the primary induces alternating magnetic field in the coil's core. Because the ignition coil's secondary has far more windings than the primary, the coil is a step-up transformer which induces a much higher voltage across the secondary windings. For an ignition coil, one end of windings of both the primary and secondary are connected together. This common point is connected to the battery (usually through a current-limiting resistor). The other end of the primary is connected to the points within the distributor. The other end of the secondary is connected, via the distributor cap and rotor, to the spark plugs.

The ignition firing sequence begins with the points (or contact breaker) closed. A steady charge flows from the battery, through the current-limiting resistor, through the coil primary, across the closed breaker points and finally back to the battery. This steady current produces a magnetic field within the coil's core. This magnetic field forms the energy reservoir that will be used to drive the ignition spark.

As the engine turns, so does the cam inside the distributor. The points ride on the cam so that as the engine turns and reaches the top of the engine's compression cycle, a high point in the cam causes the breaker points to open. This breaks the primary winding's circuit and abruptly stops the current through the breaker points. Without the steady current through the points, the magnetic field generated in the coil immediately and rapidly collapses. This change in the magnetic field induces a high voltage in the coil's secondary windings.

At the same time, current exits the coil's primary winding and begins to charge up the capacitor ("condenser") that lies across the now-open breaker points. This capacitor and the coil’s primary windings form an oscillating LC circuit. This LC circuit produces a damped, oscillating current which bounces energy between the capacitor’s electric field and the ignition coil’s magnetic field. The oscillating current in the coil’s primary, which produces an oscillating magnetic field in the coil, extends the high voltage pulse at the output of the secondary windings. This high voltage thus continues beyond the time of the initial field collapse pulse. The oscillation continues until the circuit’s energy is consumed.

The ignition coil's secondary windings are connected to the distributor cap. A turning rotor, located on top of the breaker cam within the distributor cap, sequentially connects the coil's secondary windings to one of the several wires leading to each cylinder's spark plug. The extremely high voltage from the coil's secondary -– often higher than 1000 volts—causes a spark to form across the gap of the spark plug. This, in turn, ignites the compressed air-fuel mixture within the engine. It is the creation of this spark which consumes the energy that was originally stored in the ignition coil’s magnetic field.

High performance engines with eight or more cylinders that operate at high r.p.m. (such as those used in motor racing) demand both a higher rate of spark and a higher spark energy than the simple ignition circuit can provide. This problem is overcome by using either of these adaptations:

• Two complete sets of coils, breakers and condensers can be provided - one set for each half of the engine, which is typically arranged in V-8 or V-12 configuration. Although the two ignition system halves are electrically independent, they typically share a single distributor which in this case contains two breakers driven by the rotating cam, and a rotor with two isolated conducting planes for the two high voltage inputs.
• A single breaker driven by a cam and a return spring is limited in spark rate by the onset of contact bounce or float at high rpm. This limit can be overcome by substituting for the breaker a pair of breakers that are connected electrically in series but spaced on opposite sides of the cam so they are driven out of phase. Each breaker then switches at half the rate of a single breaker and the "dwell" time for current buildup in the coil is maximized since it is shared between the breakers.

The Lamborghini V-12 engine has both these adaptations and therefore uses two ignition coils and a single distributor that contains 4 contact breakers.

A distributor-based system is not greatly different from a magneto system except that more separate elements are involved. There are also advantages to this arrangement. For example, the position of the contact breaker points relative to the engine angle can be changed a small amount dynamically, allowing the ignition timing to be automatically advanced with increasing revolutions per minute (RPM) and/or increased manifold vacuum, giving better efficiency and performance.

However it is necessary to check periodically the maximum opening gap of the breaker(s), using a feeler gauge, since this mechanical adjustment affects the "dwell" time during which the coil charges, and breakers should be re-dressed or replaced when they have become pitted by electric arcing. This system was used almost universally until the late 1970s, when electronic ignition systems started to appear.

Electronic ignition

The disadvantage of the mechanical system is the use of breaker points to interrupt the low voltage high current through the primary winding of the coil; the points are subject to mechanical wear where they ride the cam to open and shut, as well as oxidation and burning at the contact surfaces from the constant sparking. They require regular adjustment to compensate for wear, and the opening of the contact breakers, which is responsible for spark timing, is subject to mechanical variations.

In addition, the spark voltage is also dependent on contact effectiveness, and poor sparking can lead to lower engine efficiency. A mechanical contact breaker system cannot control an average ignition current of more than about 3 A while still giving a reasonable service life, and this may limit the power of the spark and ultimate engine speed.

Electronic ignition (EI) solves these problems. In the initial systems, points were still used but they only handled a low current which was used to control the high primary current through a solid state switching system. Soon, however, even these contact breaker points were replaced by an angular sensor of some kind - either optical, where a vaned rotor breaks a light beam, or more commonly using a Hall effect sensor, which responds to a rotating magnet mounted on the distributor shaft. The sensor output is shaped and processed by suitable circuitry, then used to trigger a switching device such as a thyristor, which switches a large current through the coil.

The rest of the system (distributor and spark plugs) remains as for the mechanical system. The lack of moving parts compared with the mechanical system leads to greater reliability and longer service intervals. For older cars, it is usually possible to retrofit an EI system in place of the mechanical one. In some cases, a modern distributor will fit into the older engine with no other modifications.

Other innovations are currently available on various cars. In some models, rather than one central coil, there are individual coils on each spark plug, sometimes known as direct ignition or coil on plug (COP). This allows the coil a longer time to accumulate a charge between sparks, and therefore a higher energy spark. A variation on this has each coil handle two plugs, on cylinders which are 360 degrees out of phase (and therefore reach TDC at the same time); in the four-cycle engine this means that one plug will be sparking during the end of the exhaust stroke while the other fires at the usual time, a so-called "wasted spark" arrangement which has no drawbacks apart from faster spark plug erosion; the paired cylinders are 1/4 and 2/3. Other systems do away with the distributor as a timing apparatus and use a magnetic crank angle sensor mounted on the crankshaft to trigger the ignition at the proper time.

During the 1980s, EI systems were developed alongside other improvements such as fuel injection systems. After a while it became logical to combine the functions of fuel control and ignition into one electronic system known as an engine control unit.

Digital Electronic Ignitions

At the turn of the century digital electronic ignition modules became available for small engines on such applications as chainsaws, string trimmers, leaf blowers, and lawn mowers. This was made possible by low cost, high speed, and small footprint microcontrollers. Digital electronic ignition modules can be designed as either capacitor discharge ignition (CDI) or inductive discharge ignitions (IDI). Capacitive discharge digital ignitions store charged energy for the spark in a capacitor within the module that can be released to the spark plug at virtually any time throughout the engine cycle via a control signal from the microprocessor. This allows for greater timing flexibility, and engine performance; especially when designed hand-in-hand with the engine carburetor.

Engine management

In an Engine Management System (EMS), electronics control fuel delivery, ignition timing and firing order. Primary sensors on the system are engine angle (crank or Top Dead Center (TDC) position), airflow into the engine and throttle demand position. The circuitry determines which cylinder needs fuel and how much, opens the requisite injector to deliver it, then causes a spark at the right moment to burn it.Early EMS systems used analogue computer circuit designs to accomplish this, but as embedded systems became fast enough to keep up with the changing inputs at high revolutions, digital systems started to appear.

Some designs using EMS retain the original coil, distributor and spark plugs found on cars throughout history. Other systems dispense with the distributor and coil and use special spark plugs which each contain their own coil (direct ignition). This means high voltages are not routed all over the engine, but are instead created at the point at which they are needed. Such designs offer potentially much greater reliability than conventional arrangements.

Modern EMSs usually monitor other engine parameters such as temperature and the amount of uncombined oxygen in the exhaust. This allows them to control the engine to minimise unburnt or partially burnt fuel and other noxious gases, leading to much cleaner and more efficient engines.

Turbine and jet engines

Turbine engines have a capacitor discharge ignition system using one or more igniter plugs, which are only used at startup or in case the combustor(s) flame goes out. Rocket engines have particularly demanding ignitions systems- if prompt ignition does not occur the chamber can fill with excess fuel and oxidiser and significant overpressure can occur (a 'hard start'). Rockets often employ pyrotechnic devices that place flames across the face of the injector plate, or, alternatively, self-ignition chemicals.

See also

Wikibooks has a book on the topic of Reading spark plugs for racing

• Saab Direct Ignition
• Spark-ignition

References

This article includes a list of references, related reading or external links, but its sources remain unclear because it lacks inline citations. Please improve this article by introducing more precise citations where appropriate. (May 2009)

• Spark Timing - Ignition System
• Ignition System Repairs Guide
• model-T ignition

v • d • e Car engine Part of the Automobile series Air/Fuel Air filter · Air fuel ratio meter · Automatic Performance Control · Blowoff valve · Boost · Boost controller · Butterfly valve · Carburetor · Charge cooler · Centrifugal type supercharger · Cold air intake · Engine management system · Engine Control Unit · Forced induction · Front mounted intercooler · Fuel filter · Fuel injection · Fuel pump · Fuel tank · Gasoline direct injection · Indirect injection · Intake · Intercooler · Manifold · Manifold vacuum · Mass flow sensor · Naturally-aspirated engine · Piston · Ram-air intake · Scroll-type supercharger · Short ram air intake · Supercharger · Throttle body · Top mounted intercooler · Turbocharger · Turbocharged Direct Injection · Twin-turbo · Variable Length Intake Manifold · Variable geometry turbocharger · Warm air intake Exhaust Catalytic converter · Emissions control devices · Exhaust pipe · Exhaust system · Glasspack · Muffler · Oxygen sensor Cooling Aircooling · Antifreeze · Ethylene glycol · Radiator (engine cooling) · Thermostat Ignition system Starter · Car battery · Contact breaker · Distributor · Electrical ballast · Ignition coil · Lead-acid battery · Magneto · Spark-ignition · Spark plug Other Balance shaft · Block heater · Crank · Cam · Camshaft · Connecting rod · Combustion chamber · Crank pin · Crankshaft · Crossflow cylinder head · Crossplane · Desmodromic valve · Engine knocking · Compression ratio · Crank sensor · Cylinder · Cylinder bank · Cylinder block · Cylinder head · Cylinder head porting · Dump valve · Engine balance · Oil filter · Firing order · Freeze plug · Gasket · Head gasket · Hypereutectic piston · Hydrolock · Lean burn · Main bearing · Motor oil · Multi-valve · Oil sludge · Overhead camshaft · Overhead valve · PCV valve · Piston · Piston ring · Pneumatic valve gear · Poppet valve · Power band · Redline · Reverse-flow cylinder head · Rocker arm · Seal · Sleeve valve · Starter ring gear · Synthetic oil · Tappet · Timing belt · Timing mark · Top dead centre · Underdrive pulleys · Valve float · Variable valve timing Portal · Category