phosphoric acid

 

any one of three chemical compounds made up of phosphorus, oxygen, and hydrogen (see acids and bases). The most common, orthophosphoric acid, H₃PO₄, is usually simply called phosphoric acid. Two molecules of it are formed by adding three molecules of water, H₂O, to one molecule of phosphorus pentoxide (phosphoric anhydride, P₂O₅). It occurs as rhombic crystals or as a viscous liquid; both are deliquescent. The crystals melt at about 42°C. It has specific gravity 1.834 at 18°C, is soluble in alcohol, and is very soluble in water. It is a tribasic acid and forms orthophosphate salts with either one, two, or all three of the hydrogens replaced by some other positive ion. When it is heated to about 225°C, it dehydrates to form pyrophosphoric acid, H₄P₂O₇; at still higher temperatures metaphosphoric acid, HPO₃, is formed. Salts of pyrophosphoric acid are pyrophosphates; salts of metaphosphoric acid are metaphosphates. Phosphoric acid is prepared commercially by heating calcium phosphate rock with sulfuric acid; purer grades may be prepared by treating red phosphorus with nitric acid. It is used in pickling and rust-proofing metals, in acidifying jellies and beverages, and in preparing phosphate salts.

Phosphoric acid
Other names	Orthophosphoric acid
Identifiers
CAS number	7664-38-2
Properties
Molecular formula	H3PO4
Molar mass	98.0
Appearance	white solid or colourless, viscous liquid (>42°C)
Density	1.685 g/ml (liquid)
Melting point	42.35 °C, 107.6°F, 567.27°R
Boiling point	158 °C, 415.4°F, 875.1°R decomp.
Acidity (pKa)	2.12, 7.21, 12.67
Viscosity	85% aqueous solution  ? cP
Hazards
EU classification	Corrosive(C)
R-phrases	R34
S-phrases	(S1/2), S26, S45
Related Compounds
Other anions	Nitric acid Arsenic acid
Other cations	Ammonium phosphate Trisodium phosphate
Related Phosphorus acid	Hypophosphorous acid Phosphorous acid Pyrophosphoric acid Tripolyphosphoric acid Hypophosphoric acid Perphosphoric acid Permonophosphoric acid
Except where noted otherwise, data are given for materials in their standard state (at 25 °C, 100 kPa) Infobox disclaimer and references

Phosphoric acid, also known as orthophosphoric acid or phosphoric(V) acid, is a mineral (inorganic) acid having the chemical formula H₃PO₄. Alternatively, orthophosphoric acid molecules can combine with themselves to form a variety of compounds referred to as phosphoric acids in a more general way. The term "phosphoric acid" can also refer to a chemical or reagent consisting of phosphoric acids, usually mostly orthophosphoric acid.

Orthophosphoric acid chemistry

Pure anhydrous phosphoric acid is a white solid that melts at 42.35 °C to form a colorless, viscous liquid.

Most people and even chemists simply refer to orthophosphoric acid as "phosphoric acid", which is the IUPAC name for this compound. The prefix ortho- usually is used when one wants to distinguish it from other phosphoric acids called polyphosphoric acids. Orthophosphoric acid is a non-toxic, inorganic, rather weak triprotic acid which, when pure, is a solid at room temperature and pressure. The chemical structure of orthophosphoric acid is shown above in the data table. Orthophosphoric acid is a very polar molecule, therefore it is highly soluble in water. The oxidation state of phosphorus (P) in ortho- and other phosphoric acids is +5; the oxidation state of all the oxygens (O) is -2 and all the hydrogens (H) is +1. Triprotic means that an orthophosphoric acid molecule can dissociate up to three times, giving up an H⁺ each time, which typically combines with a water molecule, H₂O, as shown in these reactions:

H₃PO_4(s)   + H₂O_(l) ⇌ H₃O⁺_(aq) + H₂PO₄^–_(aq)       K_a1= 7.5×10⁻³

H₂PO₄^–_(aq)+ H₂O_(l) ⇌ H₃O⁺_(aq) + HPO₄^2–_(aq)       K_a2= 6.2×10⁻⁸

HPO₄^2–_(aq)+ H₂O_(l) ⇌ H₃O⁺_(aq) +  PO₄^3–_(aq)        K_a3= 2.14×10⁻¹³

The anion after the first dissociation, H₂PO₄^–, is the dihydrogen phosphate anion. The anion after the second dissociation, HPO₄^2–, is the hydrogen phosphate anion. The anion after the third dissociation, PO₄^3–, is the phosphate or orthophosphate anion. For each of the dissociation reactions shown above, there is a separate acid dissociation constant, called K_a1, K_a2, and K_a3 given at 25°C. Associated with these three dissociation constants are corresponding pK_a1=2.12 , pK_a2=7.21 , and pK_a3=12.67 values at 25°C. Even though all three hydrogen (H ) atoms are equivalent on an orthophosphoric acid molecule, the successive K_a values differ since it is energetically less favorable to lose another H⁺ if one (or more) has already been lost and the molecule/ion is more negatively charged.

Because the triprotic dissociation of orthophosphoric acid, the fact that its conjugate bases (the phosphates mentioned above) cover a wide pH range, and because phosphoric acid/phosphate solutions are generally non-toxic, mixtures of these types of phosphates are often used as buffering agents or to make buffer solutions, where the desired pH depends on the proportions of the phosphates in the mixtures. Similarly, the non-toxic, anion salts of triprotic organic citric acid are also often used to make buffers. Phosphates are found pervasively in biology, especially in the compounds derived from phosphorylated sugars, such as DNA and RNA and adenosine triphosphate (ATP). There is a separate article on phosphate as an anion or its salts.

Upon heating orthophosphoric acid, condensation of the phosphoric units can be induced by driving off the water formed from condensation. When one molecule of water has been removed for each two molecules of phosphoric acid, the result is pyrophosphoric acid (H₄P₂O₇). When an average of one molecule of water per phosphoric unit has been driven off, the resulting substance is a glassy solid having an empirical formula of HPO₃ and is called metaphosphoric acid.^[1] Metaphosphoric acid is a singly anhydrous version of orthophosphoic acid and is sometimes used as a water- or moisture-absorbing reagent. Further dehydrating is very difficult and can only be accomplished by means of an extremely strong desiccant (and not by heating alone). It produces phosphoric anhydride which has an empirical formula P₂O₅, although an actual molecule has a chemical formula of P₄O₁₀. Phosphoric anhydride is a solid which is very strongly moisture-aborbing and is used as a desiccant.

Phosphoric acid as a chemical reagent

Pure 75-85% aqueous solutions (the most common) are clear, colourless, odourless, non-volatile, rather viscous, syrupy liquids, but still pourable. Phosphoric acid is very commonly used as an aqueous solution of 85% phosphoric acid or H₃PO₄. Because it is a concentrated acid, an 85% solution can be corrosive, although not toxic when diluted. Because of the high percentage of phosphoric acid in this reagent, at least some of the orthophosphoric acid is condensed into polyphosphoric acids in a temperature-dependent equilibrium, but for the sake of labeling and simplicity, the 85% represents H₃PO₄ as if it were all orthophosphoric acid. Other percentages are possible too, even above 100%, where the phosphoric acids and water would be in an unspecified equilibrium, but the overall elemental mole content would be considered specified. When aqueous solutions of phosphoric acid and/or phosphate are dilute, they are in or will reach an equilibrium after a while where practically all the phosphoric/phosphate units are in the ortho- form.

Preparation of hydrogen halides

Phosphoric acid reacts with halides to form the corresponding hydrogen halide gas (steamy fumes are observed on warming the reaction mixture). This is a common practice for the laboratory preparation of hydrogen halides.

3NaCl(s) + H₃PO₄(l) → NaH₂PO₄(s) + HCl(g)

3NaBr(s) + H₃PO₄(l) → NaH₂PO₄(s) + HBr(g)

3NaI(s) + H₃PO₄(l) → NaH₂PO₄(s) + HI(g)

Rust removal

Phosphoric acid may be used by direct application to rusted iron, steel tools or surfaces to convert iron(III) oxide (rust) to a water soluble phosphate compound. It is usually available as a greenish liquid, suitable for dipping (acid bath), but is more generally used as a component in a gel, commonly called naval jelly. As a thick gel, it may be applied to sloping, vertical, or even overhead surfaces. Care must be taken to avoid acid burns of the skin and especially the eyes, but the residue is easily diluted with water. When sufficiently diluted it can even be nutritious to plant life, containing the essential nutrients phosphorus and iron. It is sometimes sold under other names, such as "rust remover" or "rust killer". It should not be directly introduced into surface water such as creeks or into drains, however. After treatment, the reddish-brown iron oxide will be converted to a black iron phosphate compound coating that may be scrubbed off. Multiple applications of phosphoric acid may be required to remove all rust. The resultant black compound can provide further corrosion resistance (such protection is somewhat provided by the superficially similar Parkerizing and blued electrochemical conversion coating processes.) After application and removal of rust using phosphoric acid compounds, the metal should be oiled (if to be used bare, as in a tool) or appropriately painted, most durably by using a multiple coat process of primer, intermediate, and finish coats.

Processed food use

Food grade phosphoric acid is used to acidify foods and beverages such as various colas, but not without controversy as to its health effects. It provides a tangy taste, and being a mass-produced chemical, is available cheaply and in large quantities. The low cost and bulk availability is unlike more expensive natural seasonings that give comparable flavors, such as ginger for tangyness, or citric acid for sourness, obtainable from lemons and limes. (However most citric acid in the food industry is not extracted from citrus fruit, but fermented by Aspergillus niger mold from scrap molasses, waste starch hydrolysates and phosphoric acid.) It is labeled as E number E338.

Biological effects on bone calcium

Phosphoric acid, used in many soft drinks (primarily cola), has been linked to lower bone density in epidemiological studies. For example a study^[2] using dual-energy X-ray absorptiometry rather than a questionnaire about breakage, provides reasonable evidence to support the theory that drinking cola results in lower bone density. This study was published in the American Journal of Clinical Nutrition. A total of 1672 women and 1148 men were studied between 1996 and 2001. Dietary information was collected using a food frequency questionnaire that had specific questions about the number of servings of cola and other carbonated beverages and that also made a differentiation between regular, caffeine-free, and diet drinks. The paper finds statistically significant evidence to show that women who consume cola daily have lower bone density. Total phosphorus intake was not significantly higher in daily cola consumers than in nonconsumers; however, the calcium-to-phosphorus ratios were lower. The study also suggests that further research is needed to confirm the findings.

On the other hand, a study funded by Pepsi suggests that low intake of phosphorus leads to lower bone density. The study does not examine the effect of phosphoric acid, which binds with magnesium and calcium in the digestive tract to form salts that are not absorbed, but rather, it studies general phosphorus intake.^[3]

However, a well-controlled clinical study by Heaney and Rafferty using calcium-balance methods found no impact of carbonated soft drinks containing phoshporic acid on calcium excretion.^[4] The study compared the impact of water, milk and various soft drinks (two with caffeine and two without; two with phosphoric acid and two with citric acid) on the calcium balance of 20- to 40-year-old women who customarily consumed ~3 or more cups (680 ml) of a carbonated soft drink per day. They found that, relative to water, only milk and the two caffeine-containing soft drinks increased urinary calcium, and that the calcium loss associated with the caffeinated soft drink consumption was about equal to that previously found for caffeine alone. Phosphoric acid without caffeine had no impact on urine calcium, nor did it augment the urinary calcium loss related to caffeine. Because studies have shown that the effect of caffeine is compensated for by reduced calcium losses later in the day^[5], Heaney and Rafferty concluded that the net effect of carbonated beverages – including those with caffeine and phosphoric acid -- is negligible and that the skeletal effects of carbonated soft drink consumption are likely due primarily to milk displacement.

Other chemicals such as caffeine (also a significant component of popular common cola drinks) were also suspected as possible contributors to low bone density, due to the known effect of caffeine on calciuria. One other study, comprised of 30 women over the course of a week suggests that phosphoric acid in colas has no such effect, and postulates that caffeine has only a temporary effect which is later reversed. The authors of this study conclude that the skeletal effects of carbonated beverage consumption are likely due primarily to milk displacement.^[6] (Another possible confounding factor may be an association between high soft drink consumption and sedentary lifestyle.)

Medical use

Phosphoric acid is used in dentistry and orthodontics as an etching solution, to clean and roughen the surfaces of teeth where dental appliances or fillings will be placed. Phosphoric acid is also an ingredient in over the counter anti-nausea medications which also contain high levels of sugar (glucose and fructose). It should not be used by diabetics without consultation with a doctor. Phosphoric acid is also used as a catalyst in the synthesis of aspirin because it provides a larger number of hydrogen ions with less contamination when compared to hydrochloric acid and sulfuric acid.^[7]

Preparation of phosphoric acid

Phosphoric acid can be prepared by two routes - the Thermal Process and the Wet Process.

Thermal phosphoric acid: This very pure phosphoric acid is obtained by burning elemental phosphorus to produce phosphorus pentoxide and dissolving the product in dilute phosphoric acid. This produces a very pure phosphoric acid, since most impurities present in the rock have been removed when extracting Phosphorus from the rock in a furnace. The end result is food grade, thermal phosphoric acid; however, for critical applications additional processing to remove arsenic compounds may be needed.

Wet phosphoric acid: Wet process phosphoric acid is prepared by adding sulfuric acid to calcium phosphate rock.

The simplified reaction is:

3 H₂SO₄ + Ca₃(PO₄)₂ + 6 H₂O ↔ 2 H₃PO₄ + 3 CaSO₄.2H₂O + 6 H₂O

Wet process acid can be purified by removing fluorine to produce animal grade phosphoric acid or by solvent extraction and arsenic removal to produce food grade phosphoric acid.

Other applications

It is used as the electrolyte in phosphoric-acid fuel cells. It is also used as an external standard for phosphorus-31 nuclear magnetic resonance (NMR).

Phosphoric acid is used as a cleaner by construction trades to remove mineral deposits, cementitious smears, and hard water stains. It is also used as an ingredient in some household cleaners aimed at similar cleaning tasks.

Hot phosphoric acid is used in microfabrication to etch silicon nitride (Si₃N₄). It is highly selective in etching Si₃N₄ instead of SiO₂, silicon dioxide.

Phosphoric acid is used as a flux by hobbyists (such as model railroaders) as an aid to soldering.

Phosphoric acid is also used in hydroponics pH solutions to lower the pH of nutrient solutions. While other types of acids can be used, phosphorus is a nutrient used by plants, especially during flowering, making phosphoric acid particularly desirable. General Hydroponics pH Down liquid solution contains phosphoric acid in addition to citric acid and ammonium bisulfate with buffers to maintain a stable pH in the nutrient reservoir.

Phosphoric acid is used as a pH adjuster in cosmetics and skin care products.[2]

Phosphoric acid is used as a chemical oxidizing agent for activated carbon production^[8].

References

1. ^ phosphoric acid. The Columbia Encyclopedia, Sixth Edition. 2001-05
2. ^ Tucker et al. Am. J Clin. Nut. Oct 2006. Colas, but not other carbonated beverages, are associated with low bone mineral density in older women: The Framingham Osteoporosis Study.
3. ^ Elmståhl S, Gullberg B, Janzon L, et al. Increased incidence of fractures in middle-aged and elderly men with low intakes of phosphorus and zinc. Osteoporos Int 1998;8:333–40.
4. ^ Robert P Heaney and Karen Rafferty, Carbonated beverages and urinary calcium excretion, American Journal of Clinical Nutrition, Vol. 74, No. 3, 343-347, September 2001
5. ^ Barger-Lux MJ, Heaney RP, Stegman MR.[1], Effects of moderate caffeine intake on the calcium economy of premenopausal women. American Journal of Clinical Nutrition, Vol. 52:722–725
6. ^ Robert P Heaney and Karen Rafferty, Carbonated beverages and urinary calcium excretion, American Journal of Clinical Nutrition, Vol. 74, No. 3, 343-347, September 2001
7. ^ Abdullah Rathur
8. ^ C. Toles, S. Rimmera and J. C. Hower (1996). "Production of activated carbons from a Washington lignite using phosphoric acid activation". Carbon 34 (11): 1419-1426. DOI:10.1016/S0008-6223(96)00093-0. 

External links

• International Chemical Safety Card 1008
• National Pollutant Inventory - Phosphoric acid fact sheet
• NIOSH Pocket Guide to Chemical Hazards
• Excel spreadsheet containing phosphoric acid titration curve, distribution diagram and buffer pH calculation
• General Hydroponics Liquid pH Down MSDS fact sheet

Functional groups
Chemical class: Alcohol • Aldehyde • Alkane • Alkene • Alkyne • Amide • Amine • Azo compound • Benzene derivative • Carboxylic acid • Cyanate • Disulfide • Ester • Ether • Haloalkane • Imine • Isocyanide • Isocyanate • Ketone • Nitrile • Nitro compound • Nitroso compound • Peroxide • Phosphoric acid • Pyridine derivative • Sulfone • Sulfonic acid • Sulfoxide • Thioester • Thioether • Thiol

Donate to Wikimedia