rain gauge

Standard Rain Gauge

Tipping Bucket Rain Gauge Recorder

Close up of a Tipping Bucket Rain Gauge Recorder chart

A rain gauge (also known as an udometer or a pluviometer) is a type of instrument used by meteorologists and hydrologists to gather and measure the amount of liquid precipitation (as opposed to solid precipitation that is measured by a snow gauge) over a set period of time.

Most rain gauges generally measure the precipitation in millimeters. The level of rainfall is sometimes reported as inches or centimeters.

Types of rain gauges include graduated cylinders, weighing gauges, tipping bucket gauges, and simple buried pit collectors. Each type has its advantages and disadvantages for collecting rain data.

Rain gauges have their limitations. Attempting to collect rain data in a hurricane can be nearly impossible and unreliable (even if the equipment survives) due to wind extremes. Also, rain gauges only indicate rainfall in a localized area. One example of this is in Seattle: the official weather station for the city is at Seattle-Tacoma International Airport, the driest part of the city, which means that actual annual rainfall for downtown Seattle is around 254 mm (10 in) greater than official records indicate.^{[citation needed]} For virtually any gauge, drops will stick to the sides or funnel of the collecting device, such that amounts are very slightly underestimated, and those of .01 inches or .02 mm may be recorded as a trace.

Another problem encountered is when the temperature is close to or below freezing. Rain may fall on the funnel and freeze or snow may collect in the gauge and not permit any subsequent rain to pass through.

Rain gauge amounts are read either manually or by AWS (Automatic Weather Station). The frequency of readings will depend on the requirements of the collection agency. Some countries will supplement the paid weather observer with a network of volunteers to obtain precipitation data (and other types of weather) for sparsely populated areas.

In most cases the precipitation is not retained, however some stations do submit rainfall (and snowfall) for testing, which is done to obtain levels of pollutants.

Rain gauges, like most meteorological instruments, should be placed far enough away from structures and trees to ensure that any effects caused are minimised.

History

The first known records of rainfalls were kept by the Ancient Greeks about 500 B.C.^{[citation needed]} This was followed 100 years later by people in India using bowls to record the rainfall. The readings from these were correlated against expected growth, and used as a basis for land taxes.^{[citation needed]} In the Arthashastra, used for example in Magadha, precise standards were set as to grain production. Each of the state storehouses were equipped with a standardised rain gauge to classify land for taxation purposes.^[1]

The earliest rain gauge seems to be credited to a king in Korea called King Sejong who lived from 1397 to 1450. In 1441 A.D., Jang Yeong Sil, a Korean scientist, invented a standardised rain gauge called Cheokugye (측우기) as part of King Sejong's effort to measure rainfall in different regions nationwide. This program allowed for better preparation and planning on part of the farmers, and adjustments of taxes by the government officials.^[2][3][4][5]

Some sources state that the Cheokugye was the worlds first gauge while other sources say that Jang Yeong Sil developed or refined an existing gauge.^{[6][7][8][9][10][11]}

In 1662 AD, Christopher Wren created the first tipping-bucket rain gauge in Britain.^[10]

Standard rain gauge

The standard rain gauge, developed around the start of the 20th century, consists of a funnel attached to a graduated cylinder that fits into a larger container. If the water overflows from the graduated cylinder the outside container will catch it. So when it is measured the cylinder will be measured and then the excess will be put in another cylinder and measured. In most cases the cylinder is marked in mm and in the picture above will measure up to 25 mm (0.98 in) of rainfall. Each horizontal line on the cylinder is 0.2 mm (0.007 in). The larger container collects any rainfall amounts over 25 mm that flows from a small hole near the top of the cylinder. A metal pipe is attached to the container and can be adjusted to ensure the rain gauge is level. This pipe then fits over a metal rod that has been placed in the ground.

Weighing precipitation gauge

A weighing-type precipitation gauge consists of a storage bin, which is weighed to record the mass. Certain models measure the mass using a pen on a rotating drum, or by using a vibrating wire attached to a data logger. The advantages of this type of gauge to tipping buckets is that it does not underestimate intense rain, and it can measure other forms of precipitation, including rain, hail and snow. However, these gauges are more expensive and require more maintenance than tipping bucket gauges.

The weighing-type recording gauge also contains a device to measure the quantity of chemicals contained in the locations atmosphere. This is extremely helpful for scientists studying the effects of greenhouse gases released into the atmosphere and their effects on the levels of the acid rain.

Tipping bucket rain gauge

The interior of a tipping bucket rain gauge

The tipping bucket rain gauge consists of a large copper cylinder set into the ground. At the top of the cylinder is a funnel that collects and channels the precipitation. The precipitation falls onto one of two small buckets or levers which are balanced in same manner as a scale (or child's seesaw). After an amount of precipitation equal to 0.2 mm (0.007 in) falls the lever tips and an electrical signal is sent to the recorder. The recorder consists of a pen mounted on an arm attached to a geared wheel that moves once with each signal sent from the collector. When the wheel turns the pen arm moves either up or down leaving a trace on the graph and at the same time making a loud click. Each jump of the arm is sometimes referred to as a 'click' in reference to the noise. The chart is measured in 10 minute periods (vertical lines) and 0.4 mm (0.015 in) (horizontal lines) and rotates once every 24 hours and is powered by a clockwork motor that must be manually wound.

The tipping bucket rain gauge is not as accurate as the standard rain gauge because the rainfall may stop before the lever has tipped. When the next period of rain begins it may take no more than one or two drops to tip the lever. This would then indicate that 0.2 mm (0.007 in) has fallen when in fact only a minute amount has. The advantage of the tipping bucket rain gauge is that the character of the rain (light, medium or heavy) may be easily obtained. Rainfall character is decided by the total amount of rain that has fallen in a set period (usually 1 hour) and by counting the number of 'clicks' in a 10 minute period the observer can decide the character of the rain.

The exterior of a tipping bucket rain gauge

Modern tipping rain gauges consist of a plastic collector balanced over a pivot. When it tips, it actuates a switch (such as a reed switch) which is then electronically recorded or transmitted to a remote collection station.

Note that tipping gauges can incorporate weighing gauges for the best of both. In these, a strain gauge is fixed to the collection bucket so that the exact rainfall can be read at any moment. Each time the collector tips, the strain gauge (weight sensor) is re-zeroed to null out any drift.

Optical rain gauge

These have a row of collection funnels. In an enclosed space below each is a laser diode and a phototransistor detector. When enough water is collected to make a single drop, it drips from the bottom, falling into the laser beam path. The sensor is set at right angles to the laser so that enough light is scattered to be detected as a sudden flash of light. The flashes from these photodetectors are then read and transmitted or recorded.

See also

Wikimedia Commons has media related to:

Rain gauge

• Snow gauge
• disdrometer
• millimeter

References

1. ^ The Culture and Civilization of Ancient India in Historical Outline; Kosambi, 1982 ISBN 978-0706913996
2. ^ History of Rain Gauge, Mary Bellis
3. ^ History Of Weather Observing Tools WeatherShack Education Center
4. ^ Visit Busan Museum Guide
5. ^ American Meteorological Society press
6. ^ http://bueb125.com.ne.kr/san311.htm
7. ^ p. 97 Baek Seokgi. (1987). Woongjin Wi-in Jeon-gi #11 Jang Yeong-sil. Woongjin Publishing.
8. ^ Education About Asia, Vol. 6, #2, Fall, 2001.
9. ^ Friendly Korea brief on Korean history
10. ^ ^{a b} Weathershack history on rain gauge
11. ^ About.com Inventors

External links

• Report Local Rainfall across the United States here
• Report Local Rainfall Worldwide here

Donate to Wikimedia