More new questions »

Answered

In Charmed

You can buy the book repluca from some store but you could look up where to buy it i got mine at christmas!

Answered

In Mazda RX-8

My first test would be a compression test, it takes special equipment as it is a dynamic not static compression test.

Answered

V codes identify conditions other than a disease or injury and are also used to report significant factors that may influence present or future care.

Answered

V codes are specific ICD-9-CM codes used to identify encounters for reasons other than illness or injury. For an example a v code would be used for billing immunizations.. Thi…s information came from ICD-9-CM 2010 book, the 10th edition. (MORE)

Answered

In Firearms

It is hard to state a value for a Lugar without seeing it. The value will depend on the year of the gun, the condition, and other factors. If it is totally original and ha…s not been rebuilt, the value will be greater. An original pistol in excellent condition could bring $700 - $1000 from the right collector. One that is not totally original can bring $250 - $500, depending on the condition. Some may have lessor values. The only way to get an actual value is to take it to a collector for an appraisal. (MORE)

Answered

V Curve- Excitation vs Armature current V curve is the graph showing the relation of armature current as a function of field current in synchronous machines. The purpose of …the curve is to show the variation in the magnitude of the armature current as the excitation voltage of the machine is varied. Inverted V Curve- Excitation vs Power Factor The synchronous motor "V Curves" shown above illustrate the effect of excitation (field amps) on the armature (stator) amps and on system power factor. There are separate "V" Curves for No-Load and Full-Load and sometimes the motor manufacturer publishes curves for 25%, 50%, and 75% load. Note that the Armature Amperage and Power Factor "V" Curves are actually inverted "V's". Assume it is desired to determine the field excitation which will produce unity power factor operation at full motor load. Project across from the unity power factor (100%) operating point on the Y-Axis to the peak of the inverted Power Factor "V" Curve (blue line). From this intersection, project down (red line) from the full-load unity power factor (100%) operating point to determine the required field current on the X-Axis. In this example the required DC field current is shown to be just over 10 amps. Note at unity power factor operation the armature (stator) full-load amps is at the minimum value. Increasing the field amps above the value required for unity power factor operation will cause the machine to run with a leading power factor, while field weakening caused the motor power factor to become lagging. When the motor runs either leading or lagging, the armature (stator) amps increases above the unity power factor value. (MORE)

Answered

In Technology

we know motor rpm, gearbox ratio, gear spoket no of teeth, conveyor pully spoket no of teeth and conveyor pully O.D. Exm- we have a motor of 1500 rpm, gearbox ratio… 30:1, gear spoket no of teeth 24, conveyor spoket no of teeth 48, and conveyor pully (head pully) od is 200 mm, Solu- motor speed- 1500 rpm gear output - 1500/30 = 50 rpm conveyor pully rpm - 24*50/48 = 25 rpm conveyor pully cercumfrance - 200*3.14 = 628 mm or 0.628 meter conveyor speed - 25*0.628 = 15.700 meter per menuts (MORE)

Answered

That would depend on how the runner was retired at second base. For example, if the runner slipped and fell on his way to second base and the outfielder had the time to throw …him out on a force play, the batter would not get credited with a base hit. If the runner made it to second base safely and then slipped rounding the bag and the outfielder threw to second base and the runner was tagged out, the batter would be credited with a base hit. If a runner is forced out at any base, regardless of where the ball was hit, the batter is not credited with a base hit. (MORE)

Answered

In Tokio Hotel

Yes. Bill and Tom had braces when they were younger, as Tom has said in many interviews. They had the braces for 2-3 months, but had them removed, probably due to their impend…ing fame. This is why Bill once had his signature crooked teeth. (MORE)

Answered

20c + 5 = 5c + 65 Divide through by 5: 4c + 1 = c + 13 Subtract c from both sides: 3c + 1 = 13 Subtract 1 from both sides: 3c = 12 Divide both sides by 3: c = 4 20c + 5 = 5c …+65 20c - 5c= 65 - 5.
15c = 60.
15c/15 = 60/15.
c = 4 (alternative method). (MORE)