Young's modulus: Definition from Answers.com

In solid mechanics, Young's modulus (E) is a measure of the stiffness of an isotropic elastic material. It is also known as the Young modulus, modulus of elasticity, elastic modulus (though Young's modulus is actually one of several elastic moduli such as the bulk modulus and the shear modulus) or tensile modulus. It is defined as the ratio of the uniaxial stress over the uniaxial strain in the range of stress in which Hooke's Law holds.^[1] This can be experimentally determined from the slope of a stress-strain curve created during tensile tests conducted on a sample of the material.

Young's modulus is named after Thomas Young, the 19th century British scientist. However, the concept was developed in 1727 by Leonhard Euler, and the first experiments that used the concept of Young's modulus in its current form were performed by the Italian scientist Giordano Riccati in 1782 — predating Young's work by 25 years.^[2]

1 Units
2 Usage
- 2.1 Linear versus non-linear
- 2.2 Directional materials
3 Calculation
4 Approximate values
5 See also
6 Notes
7 External links

Units

Young's modulus is the ratio of stress, which has units of pressure, to strain, which is dimensionless; therefore Young's modulus itself has units of pressure.

The SI unit of modulus of elasticity (E, or less commonly Y) is the pascal (Pa or N/m²); the practical units are megapascals (MPa or N/mm²) or gigapascals (GPa or kN/mm²). In United States customary units, it is expressed as pounds (force) per square inch (psi).

Usage

The Young's modulus allows the behavior of a bar made of an isotropic elastic material to be calculated under tensile or compressive loads. For instance, it can be used to predict the amount a wire will extend under tension or buckle under compression. Some calculations also require the use of other material properties, such as the shear modulus, density, or Poisson's ratio.

Linear versus non-linear

For many materials, Young's modulus is essentially constant over a range of strains. Such materials are called linear, and are said to obey Hooke's law. Examples of linear materials include steel, carbon fiber, and glass. Rubber and soils (except at very small strains) are non-linear materials.

Directional materials

Young's modulus is not always the same in all orientations of a material. Most metals and ceramics, along with many other materials, are isotropic: Their mechanical properties are the same in all orientations. However, metals and ceramics can be treated with certain impurities, and metals can be mechanically worked to make their grain structures directional. These materials then become anisotropic, and Young's modulus will change depending on which direction the force is applied from. Anisotropy can be seen in many composites as well. For example, carbon fiber has a much higher Young's modulus (is much stiffer) when force is loaded parallel to the fibers (along the grain). Other such materials include wood and reinforced concrete. Engineers can use this directional phenomenon to their advantage in creating structures.

Calculation

Young's modulus, E, can be calculated by dividing the tensile stress by the tensile strain:

$E \equiv \frac{\mbox {tensile stress}}{\mbox {tensile strain}} = \frac{\sigma}{\varepsilon}= \frac{F/A_0}{\Delta L/L_0} = \frac{F L_0} {A_0 \Delta L}$

where

E is the Young's modulus (modulus of elasticity)

F is the force applied to the object;

A₀ is the original cross-sectional area through which the force is applied;

ΔL is the amount by which the length of the object changes;

L₀ is the original length of the object.

Force exerted by stretched or compressed material

The Young's modulus of a material can be used to calculate the force it exerts under a specific strain.

$F = \frac{E A_0 \Delta L} {L_0}$

where F is the force exerted by the material when compressed or stretched by ΔL.

Hooke's law can be derived from this formula, which describes the stiffness of an ideal spring:

$F = \left( \frac{E A_0} {L_0} \right) \Delta L = k x \,$

where

$k = \begin{matrix} \frac {E A_0} {L_0} \end{matrix} \,$

$x = \Delta L. \,$

Elastic potential energy

The elastic potential energy stored is given by the integral of this expression with respect to L:

$U_e = \int {\frac{E A_0 \Delta L} {L_0}}\, dL = \frac {E A_0} {L_0} \int { \Delta L }\, dL = \frac {E A_0 {\Delta L}^2} {2 L_0}$

where U_e is the elastic potential energy.

The elastic potential energy per unit volume is given by:

$\frac{U_e} {A_0 L_0} = \frac {E {\Delta L}^2} {2 L_0^2} = \frac {1} {2} E {\varepsilon}^2$ , where $\varepsilon = \frac {\Delta L} {L_0}$ is the strain in the material.

This formula can also be expressed as the integral of Hooke's law:

$U_e = \int {k x}\, dx = \frac {1} {2} k x^2.$

Relation among elastic constants

For homogeneous isotropic materials simple relations exist between elastic constants (Young's modulus E, shear modulus G, bulk modulus K, and Poisson's ratio ν) that allow calculating them all as long as two are known:

$E = 2G(1+\nu) = 3K(1-2\nu).\,$

Approximate values

Influences of selected glass component additions on Young's modulus of a specific base glass

Young's modulus can vary somewhat due to differences in sample composition and test method. The rate of deformation has the greatest impact on the data collected, especially in polymers. The values here are approximate and only meant for relative comparisons.

Approximate Young's modulus for various materials^[3]
Material	GPa	lbf/in² (psi)
Rubber (small strain)	0.01-0.1	1,500-15,000
ZnO NWs^{[citation needed]}	21-37	3,045,792-5,366,396
PTFE (Teflon)^{[citation needed]}	0.5	75,000
Low density polyethylene^{[citation needed]}	0.2	30,000
HDPE	0.8
Polypropylene	1.5-2	217,000-290,000
Bacteriophage capsids^{[citation needed]}	1-3	150,000-435,000
Polyethylene terephthalate	2-2.7
Polystyrene	3-3.5	435,000-505,000
Nylon	2-4	290,000-580,000
Diatom frustules (largely silicic acid)^[4]	0.35-2.77	50,000-400,000
Medium-density fibreboard^{[citation needed]}	3.654	530,000
Pine wood (along grain)^{[citation needed]}	8.963	1,300,000
Oak wood (along grain)	11	1,600,000
High-strength concrete (under compression)	30	4,350,000
Magnesium metal (Mg)	45	6,500,000
Aluminium	69	10,000,000
Glass (see chart)	50-90
Mother-of-pearl (nacre, largely calcium carbonate) ^[5]	70	10,000,000
Tooth enamel (largely calcium phosphate)^[6]	83	12,000,000
Brass and bronze	100-125	17,000,000
Titanium (Ti)		16,000,000
Titanium alloys	105-120	15,000,000-17,500,000
Copper (Cu)		17,000,000
Glass fiber reinforced plastic (70/30 by weight fibre/matrix, unidirectional, along grain)^{[citation needed]}	40-45	5,800,000-6,500,000
Carbon fiber reinforced plastic (50/50 fibre/matrix, unidirectional, along grain)^{[citation needed]}	125-150	18,000,000-22,000,000
Wrought iron	190–210
Steel	200	30,000,000
polycrystalline Yttrium iron garnet (YIG)^[7]	193	28,000,000
single-crystal Yttrium iron garnet (YIG)^[8]	200	30,000,000
Beryllium (Be)	287	42,000,000
Tungsten (W)	400-410	58,000,000-59,500,000
Sapphire (Al₂O₃) along C-axis^{[citation needed]}	435	63,000,000
Silicon carbide (SiC)	450	65,000,000
Osmium (Os)	550	79,800,000
Tungsten carbide (WC)	450-650	65,000,000-94,000,000
Single-walled carbon nanotube^[9]	1,000+	145,000,000+
Diamond (C)^[10]	1220	150,000,000-175,000,000

Notes

^ International Union of Pure and Applied Chemistry. "modulus of elasticity (Young's modulus), E". Compendium of Chemical Terminology Internet edition.
^ The Rational Mechanics of Flexible or Elastic Bodies, 1638-1788: Introduction to Leonhardi Euleri Opera Omnia, vol. X and XI, Seriei Secundae. Orell Fussli.
^ http://www.engineeringtoolbox.com/young-modulus-d_417.html
^ Subhash G, Yao S, Bellinger B, Gretz MR. (2005). "Investigation of mechanical properties of diatom frustules using nanoindentation". J Nanosci Nanotechnol.. PMID 15762160.
^ A. P. Jackson,J. F. V. Vincent and R. M. Turner (1988). "The Mechanical Design of Nacre". Proc. R. Soc. Lond. B 234: 415-440. http://rspb.royalsocietypublishing.org/content/234/1277/415.abstract.
^ M. Staines, W. H. Robinson and J. A. A. Hood (1981). "Spherical indentation of tooth enamel". Journal of Materials Science. http://www.springerlink.com/content/w125706571032231/.
^ Chou, H. M.; Case, E. D. (November, 1988), "Characterization of some mechanical properties of polycrystalline yttrium iron garnet (YIG) by non-destructive methods", Journal of Materials Science Letters 7 (11): 1217–1220, doi:10.1007/BF00722341 .
^ http://www.isowave.com/pdf/materials/Yttrium_Iron_Garnet.pdf YIG properties
^ "Electronic and mechanical properties of carbon nanotubes". http://ipn2.epfl.ch/CHBU/papers/ourpapers/Forro_NT99.pdf.
^ Spear and Dismukes (1994). Synthetic Diamond - Emerging CVD Science and Technology. Wiley, NY. ISBN 9780471535898.

External links

General subfields within physics

Acoustics · Agrophysics · Astrophysics · Atmospheric physics · Atomic, molecular, and optical physics · Biophysics · Chemical physics · Condensed matter physics · Dynamics (Fluid dynamics · Thermodynamics) · Econophysics · Electromagnetism (Optics · Electricity · Magnetism) · Geophysics · Mathematical physics · Mechanics (Classical mechanics · Quantum mechanics · Statistical mechanics) · Medical Physics · Metaphysics · Naïve physics · Neurophysics · Nuclear physics · Particle physics · Quantum field theory · Relativity (Special relativity · General relativity) · Soil Physics · Statics (Fluid statics)

v • d • e Elastic moduli for homogeneous isotropic materials

Bulk modulus ( $K$ ) • Young's modulus ( $E$ ) • Lamé's first parameter ( $λ$ ) • Shear modulus ( $G$ ) • Poisson's ratio ( $ν$ ) • P-wave modulus ( $M$ )

Conversion formulas
Homogeneous isotropic linear elastic materials have their elastic properties uniquely determined by any two moduli among these, thus given any two, any other of the elastic moduli can be calculated according to these formulas.
	$(\lambda,\,G)$	$(E,\,G)$	$(K,\,\lambda)$	$(K,\,G)$	$(\lambda,\,\nu)$	$(G,\,\nu)$	$(E,\,\nu)$	$(K,\, \nu)$	$(K,\,E)$	$(M,\,G)$
$K=\,$	$\lambda+ \frac{2G}{3}$	$\frac{EG}{3(3G-E)}$			$\lambda\frac{1+\nu}{3\nu}$	$\frac{2G(1+\nu)}{3(1-2\nu)}$	$\frac{E}{3(1-2\nu)}$			$M - \frac{4G}{3}$
$E=\,$	$G\frac{3\lambda + 2G}{\lambda + G}$		$9K\frac{K-\lambda}{3K-\lambda}$	$\frac{9KG}{3K+G}$	$\frac{\lambda(1+\nu)(1-2\nu)}{\nu}$	$2G(1+\nu)\,$		$3K(1-2\nu)\,$		$G\frac{3M-4G}{M-G}$
$\lambda=\,$		$G\frac{E-2G}{3G-E}$		$K-\frac{2G}{3}$		$\frac{2 G \nu}{1-2\nu}$	$\frac{E\nu}{(1+\nu)(1-2\nu)}$	$\frac{3K\nu}{1+\nu}$	$\frac{3K(3K-E)}{9K-E}$	$M - 2G\,$
$G=\,$			$3\frac{K-\lambda}{2}$		$\lambda\frac{1-2\nu}{2\nu}$		$\frac{E}{2(1+\nu)}$	$3K\frac{1-2\nu}{2(1+\nu)}$	$\frac{3KE}{9K-E}$
$\nu=\,$	$\frac{\lambda}{2(\lambda + G)}$	$\frac{E}{2G}-1$	$\frac{\lambda}{3K-\lambda}$	$\frac{3K-2G}{2(3K+G)}$					$\frac{3K-E}{6K}$	$\frac{M - 2G}{2M - 2G}$
$M=\,$	$\lambda+2G\,$	$G\frac{4G-E}{3G-E}$	$3K-2\lambda\,$	$K+\frac{4G}{3}$	$\lambda \frac{1-\nu}{\nu}$	$G\frac{2-2\nu}{1-2\nu}$	$E\frac{1-\nu}{(1+\nu)(1-2\nu)}$	$3K\frac{1-\nu}{1+\nu}$	$3K\frac{3K+E}{9K-E}$

This entry is from Wikipedia, the leading user-contributed encyclopedia. It may not have been reviewed by professional editors (see full disclaimer)

Donate to Wikimedia

		Sci-Tech Dictionary. McGraw-Hill Dictionary of Scientific and Technical Terms. Copyright © 2003, 1994, 1989, 1984, 1978, 1976, 1974 by McGraw-Hill Companies, Inc. All rights reserved. Read more
		Sci-Tech Encyclopedia. McGraw-Hill Encyclopedia of Science and Technology. Copyright © 2005 by The McGraw-Hill Companies, Inc. All rights reserved. Read more
		Architecture. McGraw-Hill Dictionary of Architecture and Construction. Copyright © 2003 by McGraw-Hill Companies, Inc. All rights reserved. Read more
		Sports Science and Medicine. The Oxford Dictionary of Sports Science & Medicine. Copyright © Michael Kent 1998, 2006, 2007. All rights reserved. Read more
		Columbia Encyclopedia. The Columbia Electronic Encyclopedia, Sixth Edition Copyright © 2003, Columbia University Press. Licensed from Columbia University Press. All rights reserved. www.cc.columbia.edu/cu/cup/ Read more
		Wikipedia. This article is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article "Young's modulus". Read more

	Hooke's law
	modulus of elasticity
	flexural modulus (mechanics)

	What is the difference between young's modulus and dynamic modulus of elasticity? Read answer...
	Why is Young's modulus useful? Read answer...
	Known value of Young's Modulus for steel? Read answer...

	What is the Young's modulus shear modulus and poisons ratio for polycrystalline silicon?
	What is young's modulus shear modulus and poisions ratio for polycrystalline silicon?
	Why do different materials have different young's moduli what is the unit of young's modulus?

Young's modulus

Contents